Toshiba S5ER Series User manual

SERVICE MANUAL
Color Television
FILE NO. 060-200568GR
Published in Singapore, December 2005 GREEN© TOSHIBA SINGAPORE PTE LTD
Color Television
S5ER series
14C3E1
14C3ES1
14C3T1
14C2E1
The above models are classified as green products (*1), as indicated by the underlined serial numbers.
This Service Manual describes replacement parts for green products. When repairing these green product(s), use
the part(s) described in this manual and lead-free solder (*2).
For (*1) and (*2), see the next page.
All manuals and user guides at all-guides.com
all-guides.com

– 2 –
TABLE OF CONTENTS
CHAPTER 1 GENERAL ADJUSTMENTS
SAFETY INSTRUCTIONS ............................................................................................................................................. 3
SET-UP ADJUSTMENT ................................................................................................................................................. 4
SERVICE MODE ........................................................................................................................................................... 6
DESIGN MODE ............................................................................................................................................................. 9
ELECTRICAL ADJUSTMENTS ................................................................................................................................... 10
CIRCUIT CHECK ......................................................................................................................................................... 12
CHAPTER 2 SPECIFIC INFORMATIONS
SETTING & ADJUSTING DATA ................................................................................................................................... 13
NAMES AND FUNCTIONS OF CONTROLS .............................................................................................................. 14
PROGRAMMING CHANNEL MEMORY ...................................................................................................................... 15
PROCEDURES TO SET HOTEL MODE ..................................................................................................................... 17
CHASSIS AND CABINET REPLACEMENT PARTS LIST ........................................................................................... 18
PC BOARDS BOTTOM VIEW...................................................................................................................................... 24
TERMINAL VIEW OF TRANSISTORS ........................................................................................................................ 26
CIRCUIT BLOCK DIAGRAM ....................................................................................................................................... 29
SPECIFICATIONS .................................................................................................................................................... END
APPENDIX:
CIRCUIT DIAGRAM
LEAD-FREE SOLDER
This product is manufactured using lead-free solder as a part of a movement within the consumer products industry at
large to be environmentally responsible. Lead-free solder must be used in the servicing and repair of this product.
WARNING
This product is manufactured using lead free solder.
DO NOT USE LEAD BASED SOLDER TO REPAIR THIS PRODUCT!
The melting temperature of lead-free solder is higher than that of leaded solder by 86°F to 104°F (30°C to 40°C). Use of
a soldering iron designed for lead-based solders to repair product made with lead-free solder may result in damage to
the component and or PCB being soldered. Great care should be made to ensure high-quality soldering when servicing
this product -especially when soldering large components, through-hole pins, and on PCBs - as the level of heat
required to melt lead-free solder is high.
GREEN PRODUCT PROCUREMENT
The EC is actively promoting the WEEE & RoHS Directives that define standards for recycling and reuse of Waste
Electrical and Electronic Equipment and for the Restriction of the use of certain Hazardous Substances. From July 1,
2006, the RoHS Directive will prohibit any marketing of new products containing the restricted substances.
Increasing attention is given to issues related to the global environmental. Toshiba Corporation recognizes
environmental protection as a key management tasks, and is doing its utmost to enhance and improve the quality and
scope of its environmental activities. In line with this, Toshiba proactively promotes Green Procurement, and seeks to
purchase and use products, parts and materials that have low environmental impacts.
Green procurement of parts is not only confined to manufacture. The same green parts used in manufacture must also
be used as replacement parts.
(*1)
(*2)
All manuals and user guides at all-guides.com

GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
– 3 –
2. The only source of X-RAY RADIATION in this TV receiver
is the picture tube. For continued X-RAY RADIATION
protection, the replacement tube must be exactly the same
type tube as specified in the parts list.
3. Some part in this receiver have special safety-related
characteristics for X-RAY RADIATION protection. For
continued safety, parts replacement should be undertaken
only after referring to the PRODUCT SAFETY NOTICE
below.
SAFETY PRECAUTION
WARNING : Service should not be attempted by anyone unfamiliar with the necessary precautions on this receiver. The following
are the necessary precautions to be observed before servicing this chassis.
1. An isolation transformer should be connected in the power line between the receiver and the AC line before any service is
performed on the receiver.
2. Always discharge the picture tube anode to the CRT conductive coating before handling the picture tube. The picture tube
is highly evacuated and if broken, glass fragments will be violently expelled. Use shatter proof goggles and keep picture
tube away from the unprotected body while handling.
3. When replacing a chassis in the cabinet, always be certain that all the protective devices are put back in place, such as;
nonmetallic control knobs, insulating covers, shields, isolation resistor-capacitor network etc.
CHAPTER 1 GENERAL ADJUSTMENTS
SAFETY INSTRUCTIONS
WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY PRECAU-
TION” AND “PRODUCT SAFETY NOTICE” INSTRUCTIONS BELOW.
X-RAY RADIATION PRECAUTION
1. Excessive high voltage can produce potentially hazardous
X-RAY RADIATION. To avoid such hazards, the high
voltage must not be above the specified limit. The nominal
value of the high voltage of this receiver is (A) kV at zero
beam current (minimum brightness) under a (C) V AC
power source. The high voltage must not, under any
circumstances, exceed (B) kV.
Refer to table-1 for high voltage (A), (B) & AC voltage (C).
(See SETTING & ADJUSTING DATA on page 13)
Each time a receiver requires servicing, the high voltage
should be checked following the HIGH VOLTAGE CHECK
procedure in this manual. It is recommended that the
reading of the high voltage be recorded as a part of the
service record. It is important to use an accurate and
reliable high voltage meter.
PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These characteristics are
often passed unnoticed by a visual inspection and the protection afforded by them cannot necessarily be obtained by using
replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety char-
acteristics are identified in this manual and its supplements; electrical components having such features are identified by the
international hazard symbols on the schematic diagram and the parts list.
Before replacing any of these components, read the parts list in this manual carefully. The use of substitute replacement
parts which do not have the same safety characteristics as specified in the parts list may create shock, fire, X-ray radiation
or other hazards.
All manuals and user guides at all-guides.com

GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
– 4 –
SET-UP ADJUSTMENT
RThe following adjustments should be made when a complete realignment is required or a new picture tube is installed.
Perform the adjustments in order as follows :
1. Color Purity
2. Convergence
3. White Balance
Note: The PURITY/CONVERGENCE MAGNET assembly and rubber wedges need mechanical positioning.
Refer to figure 1.
Mounting position of the purity magnet assembly should fit to same position as old one because slightly difference to
the position depend on a kind of tube.
*There are no adjustment of purity and convergence in some picture tube (Unified with purity magnet)
5. Remove the Rubber Wedges.
6. Rotate and spread the tabs of the purity magnet (See fig-
ure 2.) around the neck of the picture tube until the green
belt is in the center of the screen. At the same time, enter
the raster vertically.
7. Slowly move the yoke forward or backward until a uniform
green screen is obtained. Tighten the clamp screw of the
yoke temporarily.
8. Check the purity of the red and blue raster.
GLASS CLOTH
TAPES
DEFLECTION
YOKE
TEMPORARY
MOUNTING
RUBBER WEDGE
ADHESIVE
DEFLECTION
YOKE
PURITY/
CONVERGENCE
MAGNET ASS'Y
29.1mm(28", 29")
25mm(25")
19mm(19", 20", 21")
14mm(13", 14")
Figure 1.
WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY PRECAU-
TION”AND “PRODUCT SAFETY NOTICE”ON PAGE 3 OF THIS MANUAL.
COLOR PURITY ADJUSTMENT
NOTE : Before attempting any purity adjustments, the
receiver should be operated for at least fifteen min-
utes.
1. Demagnetize the picture tube and cabinet using a degauss-
ing coil.
2. Set the brightness and contrast to maximum.
3. Use a green raster from among the built-in test signals.
4. Loosen the clamp screw holding the yoke and slide the
yoke backward or forward to provide vertical green belt
(zone) in the picture screen.
All manuals and user guides at all-guides.com

GENERAL ADJUSTMENTS
SPECIFIC INFORMATIONS
–5 –
Figure 2.
BLU RED
BLU
RED
RED/BLU GRN
RED/BLU
GRN
B
G
R
R
G
B
BGR
RGB
BGR
RGB
R
G
B
B
G
R
4-POLE MAGNETS MOVEMENT
INCLINE THE YOKE UP (OR DOWN)
6-POLE MAGNETS MOVEMENT
Center Convergence by Convergence Magnets
Circumference Convergence by DEF Yoke
INCLINE THE YOKE RIGHT (OR LEFT)
Figure 3. Dot Movement Pattern
4-POLE
MAGNETS
PURITY
MAGNETS
6-POLE
MAGNETS
ADJUST THE ANGLE
(VERTICAL LINES) FIXED
ROTATE TWO TABS
AT THE SAME TIME
(HORIZONTAL LINES)
CONVERGENCE MAGNET ASSEMBLY ADJUSTMENT OF MAGNETS
R CIRCUMFERENCE CONVERGENCE ADJUSTMENT
1. Loosen the clamping screw of deflection yoke slightly to
allow the yoke to tilt.
2. Temporarily put a wedge as shown in figure 1. (Do not
remove cover paper on adhesive part of the wedge.)
3. Tilt front of the deflection yoke up or down to obtain better
convergence in circumference. (See figure 3.) Push the
mounted wedge into the space between picture tube and
the yoke to fix the yoke temporarily.
4. Put other wedge into bottom space and remove the cover
paper to stick.
5. Tilt front of the yoke right or left to obtain better convergence
in circumference. (See figure 3.)
6. Keep the yoke position and put another wedge in either
upper space. Remove cover paper and stick the wedge on
picture tube to fix the yoke.
7. Detach the temporarily mounted wedge and put it in an-
other upper space. Stick it on picture tube to fix the yoke.
8. After fixing three wedges, recheck overall convergence.
Tighten the screw firmly to fix the yoke and check the yoke
is firm.
9. Stick three adhesive tapes on wedges as shown in figure
1.
CONVERGENCE ADJUSTMENTS
NOTE: Before attempting any convergence adjustments, the
receiver should be operated for at least fifteen
minutes.
R CENTER CONVERGENCE ADJUSTMENT
1. Use the cross-dot pattern from among the built-in test
signals.
2. Set the brightness and contrast for well defined pattern.
3. Adjust two tabs of the 4-Pole Magnets to change the angle
between them (See figure 2.) and superimpose red
and blue vertical lines in the center area of the picture
screen.
4. Turn the both tabs at the same time keeping the angle
constant to superimpose red and blue horizontal lines at
the center of the screen.
5. Adjust two tabs of 6-Pole Magnets to superimpose red/
blue line and green one. Adjusting the angle affects the
vertical lines and rotating both magnets affects the
horizontal lines.
6. Repeat adjustments 3, 4, 5 keeping in mind red, green
and blue movement, because 4-Pole Magnets and 6-Pole
Magnets have mutual interaction and make dot movement
complex.
All manuals and user guides at all-guides.com

GENERAL ADJUSTMENTS
– 6 –
SERVICE MODE
1. ENTERING TO SERVICE MODE
1) Press obutton once on
Remote Control.
2. DISPLAYING THE ADJUSTMENT MENU
1) Press MENU button on TV.
3. KEY FUNCTION IN THE SERVICE MODE
The following key entry during display of adjustment menu provides special functions.
A single horizontal line ON/OFF: - / - - button (on Remote) or abutton (on TV)
Test signal selection : abutton (on Remote)
Selection of the adjustment items : Channel s/t(on TV or Remote)
Change of the data value : Volume ;+/– (on TV or Remote)
Adjustment menu mode ON/OFF : MENU button (on TV)
Initialization of the memory (QA02) : CALL + Channel button on TV (s)
Reset the count of operating protect
circuit to “00”: CALL + Channel button on TV (t)
“RCUT” selection : 1 button
“GCUT”selection : 2 button
“BCUT” selection : 3 button
“CNTX” (or “SCNT”) selection : 4 button
“COLC” selection : 5 button
“TNTC” selection : 6 button
“SBY” selection : 7 button
“SRY” selection : 8 button
Self diagnostic display ON/OFF : 9 button
CAUTION : Never try to perform initialization unless you have changed the memory IC.
2) Press obutton again to
keep pressing.
3) While pressing the obutton,
press MENU button on TV set.
Color thickness correction
note: Displayed differently as shown below, depending
on the setting of the receiving color system.
COLP (PAL)
COLC (NTSC)
COLS (SECAM)
S
(Service mode display)
Item
Data
Adjustment mode
Press
Press
Service mode
Item
Data
S
All manuals and user guides at all-guides.com
all-guides.com

GENERAL ADJUSTMENTS
–7 –
4. SELECTING THE ADJUSTING ITEMS
1) Every pressing of CHANNEL sbutton in the service mode changes the adjustment items in the order of table-2.
(tbutton for reverse order)
Refer to table-2 for preset data of adjustment mode.
(See SETTING & ADJUSTING DATA on page 13)
5. ADJUSTING THE DATA
1) Pressing of VOLUME ;+/–button will change the value of data in the range from 00H to FFH. The variable range
depends on the adjusting item.
6. EXIT FROM SERVICE MODE
1) Pressing POWER button to turn off the TV once.
RINITIALIZATION OF MEMORY DATA OF QA02
After replacing QA02, the following initialization is required.
1. Enter the service mode, then select any register item.
2. Press and hold the CALL button on the Remote, then press the CHANNEL sbutton on the TV. The initialization of QA02
has been complated.
3. Check the picture carefully. If necessary, adjust any adjustment item above.
Perform “Auto search Memory”on the owner’s manual.
CAUTION: Never attempt to initialize the data unless QA02 has been replaced.
7. TEST SIGNAL SELECTION
1) Every pressing of abutton on the Remote Control changes the built-in test patterns on screen as described below in
SERVICE MODE.
•Red raster
•Green raster
•Blue raster
•All Black
•All White
•Black & White
•Black cross-bar
•White cross-bar
•Black cross-bar
on green raster
•Black cross-hatch
•White cross-hatch
•Black cross-dot
•White cross-dot
•H signal (white)
•H signal (black)
Signals Picture
* The signals marked with are not usable to display in the Test signal for some model.
Signal off NTSC signals (14 patterns)
PAL signals (14 patterns)
All manuals and user guides at all-guides.com

GENERAL ADJUSTMENTS
–8 –
8. SELF DIAGNOSTIC FUNCTION
1) Press “9”button on Remote Control during display of adjustment menu in the service mode.
The diagnosis will begin to check if interface among IC’s are executed properly.
2) During diagnosis, the following displays are shown.
1Part number of microprocessor (Q100)
2Operation number of protecting circuit ----“00”is normal.
3RF signal center frequency is locked.
23 * * * * * *
POWER : 000
SYNC : OK
<SELF CHECK>
1
2
3
V/C/D R0:01111001
R1:10110000
R2:01000000
R3:10010001
<SELF CHECK>
press “9”button
Read Data
R0
R1
R2
R3
D7 D6 D5 D4 D3 D2 D1 D0
POR
V LOCK
V FREQ
COLOR SYSTEM
B DRIVE DATA
R CUTOFF DATA
IF LOCK AFT WINDOW AFT CENTER H LOCK
G DRIVE DATA
HOUT VOUT RGB OUT
STDM G CUTOFF DATA B CUTOFF DATA
PIF VCO error
det
NOISE DETCIN DC IF LEVEL ADJ TIME SYNC DET
All manuals and user guides at all-guides.com

GENERAL ADJUSTMENTS
–9 –
DESIGN MODE
2) While pressing o(or CALL) button on the
remote controller and press MENU button
on TV.
3) Press MENU button on TV.
ITEM
DATA
S D Press
(Design mode) (Adjustment mode)
Press
1. ENTERING TO DESIGN MODE
1) Select the Service mode.
(See page 6)
When QA02 is initialized, items “OPT”and “OPT1”of DESIGN MODE are set to the data of the representative model of this
chassis family.
Therefore, because ON-SCREEN specification remains in the state of the representative of model. This model is required to
reset the data of items “OPT”and “OPT1”.
2. SELECTING THE ADJUSTING ITEMS
Every pressing of CH tbutton in the design mode changes the adjustment items.
(sbutton for reverse order)
3. ADJUSTING THE DATA
Pressing of ;-/+ button will change the value of data.
All manuals and user guides at all-guides.com

GENERAL ADJUSTMENTS
– 10 –
ELECTRICAL ADJUSTMENTS
FOCUS VR ADJ
SUB-BRIGHTNESS
(BRTC)
Note: Constrict the picture height
until the vertical retrace line
appears adjusting the item
HIT (HEIGHT).
HORIZONTAL POSITION
ADJUSTMENT (HPOS)
VERTICAL POSITION
ADJUSTMENT (VPOS)
VERTICAL AMPLITUDE
ADJUSTMENT (HIT)
1. Enter the service mode, then select any register item.
2. Press the abutton on the remote controller until the black cross-bar pattern appears
on the screen.
3. Adjust the FOCUS control (on T461) for well defined scanning lines on the picture
screen.
1. Set CONTRAST to minimum, and
BRIGHTNESS to center by adjusting user
controls.
2. Set the TV in service mode to get white
cross-bar of inside pattern.
3. Select BRTC (brightness correction), and
press ;–/+ buttons to reduce the value so
that white portion of inside pattern slightly
light.
4. Press ;–/+ buttons to increase the data
value of BRTC, and set it just before the
difference between the belt of vertical retrace
and the border of black portion of inside
pattern is visible.
After that, return vertical height and contrast.
1. Set the TV in service mode, and get
black or white cross-bar signal with a
button on the remote controller.
2. Select either HPOS (Horizontal picture
phase) or VPOS (Vertical picture
phase) with CH s/tbuttons, and
adjust horizontal or vertical picture
position in the center of screen with
;–/+ buttons.
1. Set the TV in service mode, and get
black or white cross-hatch signal with
abutton on the remote controller.
2. Select HIT (Vertical amplitude) with
CH s/tbuttons, and adjust vertical
amplitude with ;–/+ buttons so that
vertical amplitude lacks a little.
3. Adjust vertical amplitude with ;–/+
buttons so that the first bar on cross-
hatch signal touches edge of screen.
Belt of vertical retrace
The first
ITEM ADJUSTMENT PROCEDURE
All manuals and user guides at all-guides.com

GENERAL ADJUSTMENTS
–11 –
WHITE BALANCE
ADJUSTMENT
•CUTOFF ADJUSTMENT
(RCUT)
(GCUT)
(BCUT)
•DRIVE ADJUSTMENT
(GDRV)
(BDRV)
1. Set Contrast to 40, and brightness to +20 by picture control.
2. Set the TV in service mode, and get the inside W/B adjusting signal with abutton.
3. Select RCUT, GCUT and BCUT with CH s/tbuttons, to set individual values to
Initial reference data, and to set GDRV and BDRV to Initial reference data with
;–/+ buttons.
4. Press button on the remote control and rotate Screen VR to get one slight
horizontal line on screen.
Note: Every pressing of button provides Horizontal line picture and Normal
picture alternately.
5. Press button to release horizontal line picture, and select the two other colors
which did not light in the above step with CH s/tbuttons. Then tap ;–/+ buttons
so that three colors slightly light in the same level.
XTo correct white balance in light area,
select GDRV and BDRV with CH s/t
buttons to adjust.
XTo correct white balance in dark area,
perform fine adjustment of RCUT, GCUT
and BCUT.
ITEM ADJUSTMENT PROCEDURE
NOTE: It is released built-in test pattern by changing the adjustment item for some model.
In this case, select the adjustment item with CH s/tbutton first and then select the built-in test pattern with
button.
Light area check
(to show white)
Dark area check
(to show black)
All manuals and user guides at all-guides.com
all-guides.com

GENERAL ADJUSTMENTS
–12 –
CIRCUIT CHECK
HIGH VOLTAGE CHECK
CAUTION: There is no HIGH VOLTAGE ADJUSTMENT on this chassis. Checking should be done following the steps below.
1. Connect an accurate high voltage meter to the second anode of the picture tube.
2. Turn on the receiver. Set the BRIGHTNESS and CONTRAST controls to minimum (zero beam current).
3. High voltage must be measured below (B) kV.
Refer to table-1 for high voltage (B).
(See SETTING & ADJUSTING DATA on page 13)
4. Vary the BRIGHTNESS control to both extremes to be sure the high voltage does not exceed the limit under any conditions.
All manuals and user guides at all-guides.com

SPECIFIC INFORMATIONS
– 13 –
CHAPTER 2 SPECIFIC INFORMATIONS
SETTING & ADJUSTING DATA
SAFETY INSTRUCTIONS
SERVICE MODE
ADJUSTING ITEMS AND DATAS IN THE SERVICE MODE:
Table-1
Table-2
14"
HIGH VOLTAGE AT ZERO BEAM: (A) 24.5 kV
MAX HIGH VOLTAGE: (B) 25.0 kV
AC VOLTAGE (C) 110-240 V
RCUT R CUTOFF (B/W) 20H ←
GCUT G CUTOFF (B/W) 20H ←
BCUT B CUTOFF (B/W) 20H ←
GDRV G DRIVE 40H ←
BDRV B DRIVE 40H ←
BRTC SUB BRIGHT CEN 40H ←
COLC SUB COLOR CEN NTSC 30H ←
TNTC SUB TINT CEN 45H ←
COLP SUB COLOR CEN PAL 09H ←
COLS SUB COLOR CEN SECAM 30H ←
SCNT SUB CONTRAST 08H ←
HPOS 50Hz H-POSITION 0DH 13H
VPOS V-POSITION 04H ←
HIT HEIGHT 1EH 24H
VLIN V-LINEARITY 0AH ←
SBY SECAM R-Y 08H ←
SRY SECAM-B-Y 08H ←
RAGC RF AGC 2AH ←
Item Adjustment Reference data Data
All manuals and user guides at all-guides.com

SPECIFIC INFORMATIONS
– 14 –
Note: The shaded buttons are not available for your TV. If you press the button, “MODE NOT AVAILABLE” will appear on the
screen.
TV Remote Control
aqMain power on/off
bqPower indicator (red)
cRemote sensor
dMENU Turn on menu display
eaInput source selection, press repeatedly to
select A1, A2 or channel position
number cyclically
f–;+ Volume down/up
Menu selection or item adjust
gtcsChannel down/up
Menu item selection
hl/ Headphones jack (3.5mm)/
LStereo headphones jack (3.5mm)
For private listening. The sound from the
speakers will be cut off automatically.
iAUDIO Audio input terminals*
jVIDEO Video input terminal
NAMES AND FUNCTIONS OF CONTROLS
TV Front and Remote control
1fPower on/standby
2oSound Mute, press again or ; –/+ to
restore the sound.
30~9 Number buttons
4aInput source selection, press repeatedly
to select A1, A2 or channel position
number cyclically
5MENU Turn on menu display
6CH s/tChannel up/down
Menu item selection
7CALL On-screen on/off
Turn off the menu
8-/-- Digit selection
9; –/+ Volume down/up
Menu selection or item adjust
!hPicture menu
8Sound menu
*
L/MONO R
(2)
9
8
1
2
3
4
5
6
7
"
!
g
f
e
d
h
i
ja
b
c
For 14C3E1, 14C3ES1, 14C3T1, 14C2E1 models
* The AUDIO R jack is not available
for 14C2E1.
All manuals and user guides at all-guides.com

SPECIFIC INFORMATIONS
–15 –
1Press MENU and then ; -/+ to highlight the “
TUNING”icon.
ON
[ + ]
[ —] [ + ]
[ —] [ + ]
AFT
ASM
SEARCH
TUN I NG
MFT
P001
[ + ]
POSITION
MEMORY
SELECT / MENU
B
2Press CH s/tto select “SEARCH”. Press ; -/+ to
start searching. Pressing “–” searches for channels at
lower frequencies while pressing “+”searches for
channels at higher frequencies. While searching,
pressing the opposite direction button, + and -
respectively, will cancel SEARCH function.
or
SEARCH
STOP
SEARCH
STOP ( + )
V L 1V L 1
Repeat this process until you can get the desired
channel.
3When the desired channel is shown, press CH tto
select “POSITION”. Press the ; -/+ buttons
repeatedly until the position number to be preset is
shown.
ON
[ + ]
[ —] [ + ]
[ —] [ + ]
AFT
ASM
SEARCH
TUN I NG
MFT
P001
[ + ]
POSITION
MEMORY
SELECT / ADJUST
B
4Press CH s/tto select “MEMORY”, then press ; +
to memorize the channel at the current position.
ON
[ + ]
[ —] [ + ]
[ —] [ + ]
AFT
ASM
SEARCH
TUN I NG
MFT
P001
[ + ]
POSITION
MEMORY
SELECT / ADJUST
B
5When you program other channels, repeat steps 2 to
4.
Preset the channels automatically
(ASM function)
Use remote control for this operation. The buttons on the TV
with similar name may also be use.
1Select the starting position for channel to be preset.
Press the Number buttons (-/--, 0~9) or CH s/t.
1
2Set the correct broadcast system for your region. Press
MENU and then ; -/+ to highlight the “SET UP”
icon.
B
Confirm “COLOR”is set to “AUTO”and “SOUND”is
set to proper system. If not, press CH s/tto select
“COLOR”or “SOUND”and press ; -/+ to set each
proper system.
3Press MENU and then ;-/+ to highlight
the “TUNING”icon. Select “ASM”, then press ;
+ to start the search. When the TV screen returns to
the start position, the procedure is complete.
CH
CH
B
To use the SEARCH function
•First, use the ASM (Automatic Search Memory) function
to preset all active channels in your area automatically.
Then, arrange the preset channels with the SEARCH,
SKIP and MFT (Manual Fine Tuning) functions so that
you can tune into only desired channels.
•Use the SEARCH function if desired channels cannot be
preset with the ASM or if you would like to preset channels
to specific position numbers one by one.
PROGRAMMING CHANNEL MEMORY
All manuals and user guides at all-guides.com

SPECIFIC INFORMATIONS
–16 –
Auto fine tuning (AFT)
If the signal frequency is unstable due to environmental
conditions, use auto fine tuning.
1Select the position number where the channel you
want to fine-tune with CH s/tor the digit selection
and number buttons (-/--, 0~9).
Note
When the position is set to “AFT OFF”status, the “R”
mark appears to the left of the position number.
25
When the channel is set to “AFT ON”status,the
position number is displayed without the “R”mark.
2Press MENU then ; -/+ to highlight the “TUNING”
icon.
3Press CH s/tto select “AFT”. Press ; -/+ to select
the “ON”indication.
ON
[ + ]
[ —] [ + ]
[ —] [ + ]
AFT
ASM
SEARCH
TUN I NG
MFT
P004
[ + ]
POSITION
MEMORY
SELECT / ADJUST
B
Notes
•When you operate MFT, AFT is switched “OFF”
automatically. If you switch on AFT after fine tuning with
MFT, MFT may be canceled.
•AFT may be set independently for each position.
To skip a position number
After presetting the channels, you may skip unnecessary
position numbers so that only the channels you want to watch
are selected using CH s/t.
1First, select the position number to be skipped with
CH s/tor digit selection and number buttons (-/--,
0~9).
2Highlight the “SET UP”icon and press CH s/tto
select “SKIP”.
B/G
OFF
AUTO
SOUND
SK I P
SET UP
COLOR
SELECT / ADJUST
B
3Press the ; -/+ to set “SKIP”to “ON”. This completes
the setting for skipping the selected position number.
Notes
•When “SKIP”is set to “ON”for the selected position
number, a “* ”mark appears to the left of the position
number.
12
The position number will then be skipped when you select
the position with the CH s/tbuttons.
•If you want to restore a skipped position number, select it
using the -/-- and 0~9 buttons then switch the “SKIP”setting
to “OFF”.
Manual fine tuning (MFT)
The adjustments below are not necessary under normal
conditions. However, under some reception conditions, fine
tuning may be necessary to improve the picture quality. In
such cases, adjust the manual fine tuning (MFT).
1Select the position number where the channel you
want to fine-tune with CH s/tor digit selection and
number buttons (-/--,0~9).
2Press MENU and then ; -/+ to highlight the “
TUNING”icon.
3Press CH s/tto select “MFT”. Press ; -/+ to start
fine tuning. Press ; -/+ repeatedly until the best
possible picture and sound are obtained.
ON
[ + ]
[ —] [ + ]
[ —] [ + ]
AFT
ASM
SEARCH
TUN I NG
MFT
P004
[ + ]
POSITION
MEMORY
SELECT / ADJUST
B
All manuals and user guides at all-guides.com
all-guides.com

SPECIFIC INFORMATIONS
–17 –
PROCEDURES TO SET HOTEL MODE
1. Set the Channel Programs which you want the Customer to watch.
1) Use ASM (see page 15) or SEARCH (see page 15) to select the programs.
2) Choice the position you want the programs to be stored in TUNING menu.
3) Save the programs by MEMORY operation in TUNING menu (see page 15).
2. Set the Channels which you don’t want the Customer to access
1) Select the channel by pressing the number buttons or CH s/tbuttons.
2) Set the SKIP from OFF to ON (see page 16).
3) Repeat above 1) & 2) for all the channels which need to be blocked.
3. Activate the HOTEL Mode:
1) Select startup channel (TV, A1, A2) first, then enter into design mode (see page 9).
2) Press CH tbutton on the remote controller to show the Design Item “OPT”.
3) Add “0x80”to the data of “OPT”to activate the HOTEL Mode with panel buttons unlocked, or add “0x08”to the data
of “OPT2”to activate the HOTEL Mode with panel buttons locked.
4) AC Power OFF the TV, then next time AC Power ON the TV will in HOTEL Mode with all the customer settings
taking effect.
4. Set the maximum volume:
1) Enter Service Mode (see page 6).
2) Enter Design Mode (see page 9).
3) Use the CH tbutton on the remote controller to show the Design Item “VOLX”.
4) Adjust the “VOLX”data by pressing ;+/- buttons (Default 0x64 is equal to Volume 100 in Decimal).
5. Set the following Items in HOTEL Mode:
1) Picture mode
Press hbutton to select the desired picture quality. “DYNAMIC”, “STANDARD”, “MILD”and “MEMORY”will appear
cyclically.
2) Sound mode
Press 8button to select the desired sound quality. “THEATER”, “NEWS”and “MEMORY”will appear cyclically.
(Every time AC Power ON the TV will call back the above customer setting.)
All manuals and user guides at all-guides.com

– 18 –
SPECIFIC INFORMATIONS
CHASSIS AND CABINET REPLACEMENT PARTS LIST
WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY PRE-
CAUTION” AND “PRODUCT SAFETY NOTICE” ON PAGE 3 OF THIS MANUAL.
CAUTION: The international hazard symbols “ ” in the schematic diagram and the parts list designate components
which have special characteristics important for safety and should be replaced only with types identical to those in the
original circuit or specified in the parts list. The mounting position of replacements is to be identical with originals.
Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE. Do not degrade the safety
of the receiver through improper servicing.
NOTICE:
•The part number must be used when ordering parts, in order to assist in processing, be sure to include the
Model number and Description.
•The PC board assembly with *mark is no longer available after the end of the production.
Model: 14C3E1/14C3ES1/14C3T1/14C2E1
Capacitors .......... CD : Ceramic Disk PF : Plastic Film EL : Electrolytic
Resistors ............ CF : Carbon Film CC : Carbon Composition MF : Metal Film
OMF : Oxide Metal Film VR : Variable Resistor FR : Fusible Resistor
(All CD and PF capacitors are ±5%, 50V and all resistors, ±5%, 1/6W unless otherwise noted.)
Location Parts No. Description
No.
#1: [14C3E1]
#2: [14C3ES1]
#3: [14C3T1]
#4: [14C2E1]
CAPACITORS
C101 76794101 ELECTROLYTIC, 16V 100UF M
C102 76763221 ELECTROLYTIC, 16V 220UF M
C103 #1 76109103 CERAMIC CHIP, 50V B 0.01UF K
#2 76109103 CERAMIC CHIP, 50V B 0.01UF K
#4 76109103 CERAMIC CHIP, 50V B 0.01UF K
C104 #1 76105470 CERAMIC CHIP, 50V CH 47PF J
#2 76105470 CERAMIC CHIP, 50V CH 47PF J
#4 76105470 CERAMIC CHIP, 50V CH 47PF J
C106 76796479 ELECTROLYTIC, 35V 4.7UF M
C108 76795100 ELECTROLYTIC, 25V 10UF M
C111 #3 76105470 CERAMIC CHIP, 50V CH 47PF J
C112 #3 76105470 CERAMIC CHIP, 50V CH 47PF J
C113 76109102 CERAMIC CHIP, 50V B 1000PF K
C114 76109102 CERAMIC CHIP, 50V B 1000PF K
C118 76109102 CERAMIC CHIP, 50V B 1000PF K
C120 76203100 ELECTORLYTIC, 16V 10UF M
C121 76109103 CERAMIC CHIP, 50V B 0.01UF K
C123 76206010 ELECTROLYTIC, 50V 1UF M
C129 76109102 CERAMIC CHIP, 50V B 1000PF K
C130 76797479 ELECTROLYTIC, 50V 4.7UF M
C131 76814103 CERAMIC CHIP, 50V F 0.01UF Z
C132 76100104 CERAMIC CHIP, 25V F 0.1UF Z
C133 76105101 CERAMIC CHIP, 50V CH 100PF J
C135 76109222 CERAMIC CHIP, 50V B 2200PF K
C136 76206228 ELECTROLYTIC, 50V 0.22UF M
C137 76100103 CERAMIC CHIP, 50V F 0.01UF Z
C138 76794470 ELECTROLYTIC, 16V 47UF M
C141 76105101 CERAMIC CHIP, 50V CH 100PF J
C150 #1 76814103 CERAMIC CHIP, 50V F 0.01UF Z
#2 76814103 CERAMIC CHIP, 50V F 0.01UF Z
#4 76814103 CERAMIC CHIP, 50V F 0.01UF Z
C166 76109103 CERAMIC CHIP, 50V B 0.01UF K
C167 76794101 ELECTROLYTIC, 16V 100UF M
C170 76109103 CERAMIC CHIP, 50V B 0.01UF K
C171 #1 76203100 ELECTORLYTIC, 16V 10UF M
#2 76203100 CAPACITOR, ELECTORLYTIC, 16V 10UF M
#4 76203100 ELECTORLYTIC, 16V 10UF M
C172 #1 76203100 ELECTORLYTIC, 16V 10UF M
#2 76203100 ELECTORLYTIC, 16V 10UF M
#4 76203100 ELECTORLYTIC, 16V 10UF M
C173 #1 76203100 ELECTORLYTIC, 16V 10UF M
#2 76203100 ELECTORLYTIC, 16V 10UF M
#4 76203100 ELECTORLYTIC, 16V 10UF M
C174 76105330 CERAMIC CHIP, 50V CH 33PF J
C175 76105330 CERAMIC CHIP, 50V CH 33PF J
C176 76105330 CERAMIC CHIP, 50V CH 33PF J
C179 #3 76109103 CERAMIC CHIP, 50V B 0.01UF K
C180 #3 76109103 CERAMIC CHIP, 50V B 0.01UF K
C189 76206478 ELECTROLYTIC, 50V 0.47UF M
C192 76206478 ELECTROLYTIC, 50V 0.47UF M
C216 76206010 ELECTROLYTIC, 50V 1UF M
C221 76105101 CERAMIC CHIP, 50V CH 100PF J
C222 76105101 CERAMIC CHIP, 50V CH 100PF J
C223 76105101 CERAMIC CHIP, 50V CH 100PF J
C224 76203100 ELECTORLYTIC, 16V 10UF M
C226 76100104 CERAMIC CHIP, 25V F 0.1UF Z
C227 76100104 CERAMIC CHIP, 25V F 0.1UF Z
C234 76109103 CERAMIC CHIP, 50V B 0.01UF K
C235 76109103 CERAMIC CHIP, 50V B 0.01UF K
C305 76617915 ELECTROLYTIC, 50V 1UF K
C306 76794102 ELECTROLYTIC, 16V 1000UF M
C307 76693473 PLASTIC FILM, 100V 0.047UF J
C308 76765101 ELECTROLYTIC, 35V 100UF M
C309 76203100 ELECTORLYTIC, 16V 10UF M
C312 76796102 ELECTROLYTIC, 35V 1000UF M
C313 76082280 PLASTIC FILM, 100V 0.22UF J
C314 76212152 CERAMIC DISC, 50V B 1500PF K
C315 76503049 PLASTIC FILM, 63V 0.47UF J
C317 76214471 CERAMIC DISC, 500V B 470PF K
C320 76765101 ELECTROLYTIC, 35V 100UF M
C410 76693472 PLASTIC FILM, 100V 4700PF J
C417 76214102 CERAMIC DISC, 500V B 1000PF K
C420 76794220 ELECTROLYTIC, 16V 22UF M
C421 76794470 ELECTROLYTIC, 16V 47UF M
C431 76797479 ELECTROLYTIC, 50V 4.7UF M
C432 76203100 ELECTORLYTIC, 16V 10UF M
C433 76100103 CERAMIC CHIP, 50V F 0.01UF Z
C434 76100103 CERAMIC CHIP, 50V F 0.01UF Z
C435 76763471 ELECTROLYTIC, 16V 470UF M
C436 76206478 ELECTROLYTIC, 50V 0.47UF M
C437 76109822 CERAMIC CHIP, 50V B 8200PF K
C438 76100103 CERAMIC CHIP, 50V F 0.01UF Z
C439 76105470 CERAMIC CHIP, 50V CH 47PF J
C440 76503264 PLASTIC FILM, 1250VH 7200PF H
C442 76082994 PLASTIC FILM, 250V 0.3UF J
C445 76693104 PLASTIC FILM, 100V 0.1UF J
C446 76679100 ELECTROLYTIC, 250V 10UF M
C448 76678220 ELECTROLYTIC, 200V 22UF M
C449 76763471 ELECTROLYTIC, 16V 470UF M
C463 76109152 CERAMIC CHIP, 50V B 1500PF K
C484 #1 76591104 PLASTIC FILM, 50V 0.1UF J
#2 76591104 PLASTIC FILM, 50V 0.1UF J
Location Parts No. Description
No.
All manuals and user guides at all-guides.com

– 19 –
SPECIFIC INFORMATIONS
C484 #3 76590104 CERAMIC DISC, 50V 0.1UF J
#4 76591104 PLASTIC FILM, 50V 0.1UF J
C485 #1 76591104 PLASTIC FILM, 50V 0.1UF J
#2 76591104 PLASTIC FILM, 50V 0.1UF J
#3 76590104 CERAMIC DISC, 50V 0.1UF J
#4 76591104 PLASTIC FILM, 50V 0.1UF J
C502 #1 76591103 PLASTIC FILM, 50V 0.01UF J
#2 76591103 PLASTIC FILM, 50V 0.01UF J
#3 76590103 PLASTIC FILM, 50V 0.01UF J
#4 76591103 PLASTIC FILM, 50V 0.01UF J
C517 76203100 ELECTORLYTIC, 16V 10UF M
C523 76203100 ELECTORLYTIC, 16V 10UF M
C526 76109102 CERAMIC CHIP, 50V B 1000PF K
C528 76206478 ELECTROLYTIC, 50V 0.47UF M
C567 76109103 CERAMIC CHIP, 50V B 0.01UF K
C606 76206010 ELECTROLYTIC, 50V 1UF M
C607 76764101 ELECTROLYTIC, 25V 100UF M
C608 76206010 ELECTROLYTIC, 50V 1UF M
C609 76206478 ELECTROLYTIC, 50V 0.47UF M
C610 76667102 ELECTROLYTIC, 25V 1000UF M
C611 76100103 CERAMIC CHIP, 50V F 0.01UF Z
C612 76795100 ELECTROLYTIC, 25V 10UF M
C615 76795471 ELECTROLYTIC, 25V 470UF M
C616 76667471 ELECTROLYTIC, 25V 470UF M
C630 76667471 ELECTROLYTIC, 25V 470UF M
C631 76797229 ELECTROLYTIC, 50V 2.2UF M
C632 76109102 CERAMIC CHIP, 50V B 1000PF K
C635 76797229 ELECTROLYTIC, 50V 2.2UF M
C636 76109102 CERAMIC CHIP, 50V B 1000PF K
C651 76206228 ELECTROLYTIC, 50V 0.22UF M
C653 76100104 CERAMIC CHIP, 25V F 0.1UF Z
C654 76206228 ELECTROLYTIC, 50V 0.22UF M
C655 76100104 CERAMIC CHIP, 25V F 0.1UF Z
C656 76100104 CERAMIC CHIP, 25V F 0.1UF Z
C657 76766220 ELECTROLYTIC, 50V 22UF M
C658 76109472 CERAMIC CHIP, 50V B 4700PF K
C669 76109103 CERAMIC CHIP, 50V B 0.01UF K
C675 76109822 CERAMIC CHIP, 50V B 8200PF K
C678 76109822 CERAMIC CHIP, 50V B 8200PF K
C679 76797479 ELECTROLYTIC, 50V 4.7UF M
C680 76766101 ELECTROLYTIC, 50V 100UF M
C681 76206478 ELECTROLYTIC, 50V 0.47UF M
C682 76206478 ELECTROLYTIC, 50V 0.47UF M
C683 76109472 CERAMIC CHIP, 50V B 4700PF K
C684 76109222 CERAMIC CHIP, 50V B 2200PF K
C686 76100104 CERAMIC CHIP, 25V F 0.1UF Z
C688 76109103 CERAMIC CHIP, 50V B 0.01UF K
C689 76100104 CERAMIC CHIP, 25V F 0.1UF Z
C691 76100104 CERAMIC CHIP, 25V F 0.1UF Z
C692 76100104 CERAMIC CHIP, 25V F 0.1UF Z
C693 76100104 CERAMIC CHIP, 25V F 0.1UF Z
C694 76100104 CERAMIC CHIP, 25V F 0.1UF Z
C695 76100104 CERAMIC CHIP, 25V F 0.1UF Z
C696 76100104 CERAMIC CHIP, 25V F 0.1UF Z
C697 76100104 CERAMIC CHIP, 25V F 0.1UF Z
zC801 76503507 PLASTIC FILM, AC275V 0.22UF K
C810 76125031 BLOCK CAP 400V150M
zC813 76166021 CERA CAP E 250V 102
zC814 76166021 CERA CAP E 250V 102
C840 76590104 CERAMIC DISC, 50V 0.1UF J
C841 76590104 CERAMIC DISC, 50V 0.1UF J
C861 76214471 CERAMIC DISC, 500V B 470PF K
C864 76797221 ELECTROLYTIC, 50V 220UF M
C873 76092341 CERAMIC DISC, 2KV R 470PF K
C874 #1 76591104 PLASTIC FILM, 50V 0.1UF J
#2 76591104 PLASTIC FILM, 50V 0.1UF J
#3 76590104 CERAMIC DISC, 50V 0.1UF J
#4 76591104 PLASTIC FILM, 50V 0.1UF J
C875 76109681 CERAMIC CHIP, 50V B 680PF K
C876 76109102 CERAMIC CHIP, 50V B 1000PF K
C877 76100103 CERAMIC CHIP, 50V F 0.01UF Z
C878 76092341 CERAMIC DISC, 2KV R 470PF K
C879 76797479 ELECTROLYTIC, 50V 4.7UF M
C880 76100103 CERAMIC CHIP, 50V F 0.01UF Z
C884 76640018 ELECTROLYTIC, 160V 220UF
C885 76214471 CERAMIC DISC, 500V B 470PF K
C889 76764222 ELECTROLYTIC, 25V 2200UF M
C893 76092341 CERAMIC DISC, 2KV R 470PF K
zC896 76166006 CERA CAP B 250V471K
zC897 76166010 CERA CAP E 250V222M
C899 76503045 PLASTIC FILM, 63V 0.22UF J
C902 76092347 CERAMIC DISC, 2KV R 1500PF K
C904 76109391 CERAMIC CHIP, 50V B 390PF K
C905 76109331 CERAMIC CHIP, 50V B 330PF K
C907 76109391 CERAMIC CHIP, 50V B 390PF K
C910 76206478 ELECTROLYTIC, 50V 0.47UF M
C912 76763471 ELECTROLYTIC, 16V 470UF M
C913 76203100 ELECTORLYTIC, 16V 10UF M
C971 76794470 ELECTROLYTIC, 16V 47UF M
CA01 76232103 CERAMIC DISC, 50V F 0.01UF Z
CA02 76105101 CERAMIC CHIP, 50V CH 100PF J
CA03 76105220 CERAMIC CHIP, 50V CH 22PF J
CA04 76105220 CERAMIC CHIP, 50V CH 22PF J
CA30 76105221 CERAMIC CHIP, 50V CH 220PF J
CA42 76203100 ELECTORLYTIC, 16V 10UF M
CA45 76109103 CERAMIC CHIP, 50V B 0.01UF K
CB01 76794470 ELECTROLYTIC, 16V 47UF M
CC01 76109103 CERAMIC CHIP, 50V B 0.01UF K
CS02 #1 76794100 ELECTROLYTIC, 16V 10UF M
#2 76203100 ELECTORLYTIC, 16V 10UF M
#3 76203100 ELECTORLYTIC, 16V 10UF M
#4 76203100 ELECTORLYTIC, 16V 10UF M
CS04 76109102 CERAMIC CHIP, 50V B 1000PF K
CS05 76109102 CERAMIC CHIP, 50V B 1000PF K
CS07 76109102 CERAMIC CHIP, 50V B 1000PF K
CS10 #1 76109102 CERAMIC CHIP, 50V B 1000PF K
#2 76109102 CERAMIC CHIP, 50V B 1000PF K
#3 76109102 CERAMIC CHIP, 50V B 1000PF K
CS11 #1 76203100 ELECTORLYTIC, 16V 10UF M
#2 76203100 ELECTORLYTIC, 16V 10UF M
#3 76203100 ELECTORLYTIC, 16V 10UF M
CS13 #1 76109102 CERAMIC CHIP, 50V B 1000PF K
#2 76109102 CERAMIC CHIP, 50V B 1000PF K
#3 76109102 CERAMIC CHIP, 50V B 1000PF K
CS14 #1 76109102 CERAMIC CHIP, 50V B 1000PF K
#2 76109102 CERAMIC CHIP, 50V B 1000PF K
#3 76109102 CERAMIC CHIP, 50V B 1000PF K
CS23 76203100 ELECTORLYTIC, 16V 10UF M
CS25 76203100 ELECTORLYTIC, 16V 10UF M
CV10 76762471 ELECTROLYTIC, 10V 470UF M
CV28 76203100 ELECTORLYTIC, 16V 10UF M
ZC01 #1 23303398 FILTER, CERAMIC TRAP 39.5MHZ XT39.5MA
#2 23303398 FILTER, CERAMIC TRAP 39.5MHZ XT39.5MA
#4 23303398 FILTER, CERAMIC TRAP 39.5MHZ XT39.5MA
ZC02 #1 23303397 FILTER, CERAMIC TRAP 30MHZ XT30.0MA
#2 23303397 FILTER, CERAMIC TRAP 30MHZ XT30.0MA
#4 23303397 FILTER, CERAMIC TRAP 30MHZ XT30.0MA
RESISTORS
G218 76366392 CARBON FILM, 1/6W 3.9K OHM J
G402 23103308 FERRITE CORE, TEM2011AO, 3.5X4.5
G902 76000824 CHIP JUMPER, 2125TYPE
G903 76000824 CHIP JUMPER, 2125TYPE
G941 76000445 CHIP JUMPER, 1608TYPE
G942 76000445 CHIP JUMPER, 1608TYPE
G943 76000445 CHIP JUMPER, 1608TYPE
GD433 76000824 CHIP JUMPER, 2125TYPE
GJ01 76011472 CHIP, 1/20W 4.7K OHM J
GJ02 76011472 CHIP, 1/20W 4.7K OHM J
GJ03 76000445 CHIP JUMPER, 1608TYPE
GJ05 76000445 CHIP JUMPER, 1608TYPE
GJ06 #1 76000445 CHIP JUMPER, 1608TYPE
#2 76000445 CHIP JUMPER, 1608TYPE
#4 76000445 CHIP JUMPER, 1608TYPE
GJ08 #3 76000445 CHIP JUMPER, 1608TYPE
GJ09 #3 76000445 CHIP JUMPER, 1608TYPE
GJ10 #1 76000445 CHIP JUMPER, 1608TYPE
#2 76000445 CHIP JUMPER, 1608TYPE
#4 76000445 CHIP JUMPER, 1608TYPE
GJ100 76000445 CHIP JUMPER, 1608TYPE
GJ11 76000445 CHIP JUMPER, 1608TYPE
GJ12 #1 76000445 CHIP JUMPER, 1608TYPE
#2 76000445 CHIP JUMPER, 1608TYPE
#4 76000445 CHIP JUMPER, 1608TYPE
GJ20 #4 76000445 CHIP JUMPER, 1608TYPE
GJ21 76000445 CHIP JUMPER, 1608TYPE
GJ25 76000445 CHIP JUMPER, 1608TYPE
GJ27 76000445 CHIP JUMPER, 1608TYPE
Location Parts No. Description
No.
Location Parts No. Description
No.
All manuals and user guides at all-guides.com

–20 –
SPECIFIC INFORMATIONS
GJ29 #4 76000445 CHIP JUMPER, 1608TYPE
GJ30 76000445 CHIP JUMPER, 1608TYPE
GL431 76000445 CHIP JUMPER, 1608TYPE
GL525 76000445 CHIP JUMPER, 1608TYPE
GR01 76000445 CHIP JUMPER, 1608TYPE
GR02 76000445 CHIP JUMPER, 1608TYPE
GR03 76000445 CHIP JUMPER, 1608TYPE
GR04 #1 76000445 CHIP JUMPER, 1608TYPE
#2 76000445 CHIP JUMPER, 1608TYPE
#3 76000445 CHIP JUMPER, 1608TYPE
GR05 #1 76000445 CHIP JUMPER, 1608TYPE
#2 76000445 CHIP JUMPER, 1608TYPE
#3 76000445 CHIP JUMPER, 1608TYPE
GR06 #1 76000445 CHIP JUMPER, 1608TYPE
#2 76000445 CHIP JUMPER, 1608TYPE
#3 76000445 CHIP JUMPER, 1608TYPE
GR106 #3 76000445 CHIP JUMPER, 1608TYPE
GR160 76011470 CHIP, 1/20W 47 OHM J
GR303 76182003 METAL ERX1SJS1R0P
GR884 76322688 OXIDE METAL FILM, 1W 0.68 OHM J
JR001 76000445 CHIP JUMPER, 1608TYPE
JR002 76000445 CHIP JUMPER, 1608TYPE
JR003 76000445 CHIP JUMPER, 1608TYPE
JR004 76000445 CHIP JUMPER, 1608TYPE
JR005 #1 76000824 CHIP JUMPER, 2125TYPE
JR006 76000576 CHIP JUMPER, 3216TYPE
JR007 76000576 CHIP JUMPER, 3216TYPE
JR008 #1 76000576 CHIP JUMPER, 3216TYPE
JR010 76000576 CHIP JUMPER, 3216TYPE
R101 76011563 CHIP, 1/20W 56K OHM J
R102 76011123 CHIP, 1/20W 12K OHM J
R103 #3 76011101 CHIP, 1/20W 100 OHM J
R104 #3 76011222 CHIP, 1/20W 2.2K OHM J
R105 #1 76011331 CHIP, 1/20W 330 OHM J
#2 76011331 CHIP, 1/20W 330 OHM J
#3 76011121 CHIP, 1/20W 120 OHM J
#4 76011331 CHIP, 1/20W 330 OHM J
R106 76011332 CHIP, 1/20W 3.3K OHM J
R107 #1 76011330 CHIP, 1/20W 33 OHM J
#2 76011330 CHIP, 1/20W 33 OHM J
#4 76011330 CHIP, 1/20W 33 OHM J
R108 #1 76011272 CHIP, 1/20W 2.7K OHM J
#2 76011272 CHIP, 1/20W 2.7K OHM J
#3 76011122 CHIP, 1/20W 1.2K OHM J
#4 76011272 CHIP, 1/20W 2.7K OHM J
R109 76011682 CHIP, 1/20W 6.8K OHM J
R110 #1 76011102 CHIP, 1/20W 1K OHM J
#2 76011102 CHIP, 1/20W 1K OHM J
#3 76011681 CHIP, 1/20W 680 OHM J
#4 76011102 CHIP, 1/20W 1K OHM J
R111 #1 76011360 CHIP, 1/20W 36 OHM J
#2 76011360 CHIP, 1/20W 36 OHM J
#3 76011330 CHIP, 1/20W 33 OHM J
#4 76011360 CHIP, 1/20W 36 OHM J
R112 #1 76000445 CHIP JUMPER, 1608TYPE
#2 76000445 CHIP JUMPER, 1608TYPE
#3 76011221 CHIP, 1/20W 220 OHM J
#4 76000445 CHIP JUMPER, 1608TYPE
R113 #1 76011222 CHIP, 1/20W 2.2K OHM J
#2 76011222 CHIP, 1/20W 2.2K OHM J
#4 76011222 CHIP, 1/20W 2.2K OHM J
R114 #1 76011472 CHIP, 1/20W 4.7K OHM J
#2 76011472 CHIP, 1/20W 4.7K OHM J
#4 76011472 CHIP, 1/20W 4.7K OHM J
R116 #1 76011682 CHIP, 1/20W 6.8K OHM J
#2 76011682 CHIP, 1/20W 6.8K OHM J
#4 76011682 CHIP, 1/20W 6.8K OHM J
R117 #1 76011222 CHIP, 1/20W 2.2K OHM J
#2 76011222 CHIP, 1/20W 2.2K OHM J
#4 76011222 CHIP, 1/20W 2.2K OHM J
R118 #3 76011821 CHIP, 1/20W 820 OHM J
R120 76011684 CHIP, 1/20W 680K OHM J
R121 76011221 CHIP, 1/20W 220 OHM J
R122 76000445 CHIP JUMPER, 1608TYPE
R124 #1 76011102 CHIP, 1/20W 1K OHM J
#2 76011102 CHIP, 1/20W 1K OHM J
#4 76011102 CHIP, 1/20W 1K OHM J
R125 #3 76011222 CHIP, 1/20W 2.2K OHM J
R126 #3 76011101 CHIP, 1/20W 100 OHM J
R127 #3 76011103 CHIP, 1/20W 10K OHM J
R128 #3 76011103 CHIP, 1/20W 10K OHM J
R129 #3 76011102 CHIP, 1/20W 1K OHM J
R130 76011101 CHIP, 1/20W 100 OHM J
R131 76011221 CHIP, 1/20W 220 OHM J
R132 #1 76011271 CHIP, 1/20W 270 OHM J
#2 76011271 CHIP, 1/20W 270 OHM J
#4 76011271 CHIP, 1/20W 270 OHM J
R133 #1 76011271 CHIP, 1/20W 270 OHM J
#2 76011271 CHIP, 1/20W 270 OHM J
#4 76011271 CHIP, 1/20W 270 OHM J
R134 #1 76011561 CHIP, 1/20W 560 OHM J
#2 76011561 CHIP, 1/20W 560 OHM J
#3 76011221 CHIP, 1/20W 220 OHM J
#4 76011561 CHIP, 1/20W 560 OHM J
R136 76011513 CHIP, 1/20W 51K OHM J
R137 #3 76011221 CHIP, 1/20W 220 OHM J
R138 #3 76011221 CHIP, 1/20W 220 OHM J
R139 76011332 CHIP, 1/20W 3.3K OHM J
R141 76011331 CHIP, 1/20W 330 OHM J
R142 76011102 CHIP, 1/20W 1K OHM J
R143 76011333 CHIP, 1/20W 33K OHM J
R144 76011103 CHIP, 1/20W 10K OHM J
R145 76011303 CHIP, 1/20W 30K OHM J
R146 76011224 CHIP, 1/20W 220K OHM J
R147 76011152 CHIP, 1/20W 1.5K OHM J
R148 76011222 CHIP, 1/20W 2.2K OHM J
R150 76000445 CHIP JUMPER, 1608TYPE
R156 76553153 OXIDE METAL FILM, 1W 15K OHM J
R158 76011122 CHIP, 1/20W 1.2K OHM J
R166 76011103 CHIP, 1/20W 10K OHM J
R167 76011103 CHIP, 1/20W 10K OHM J
R168 76011473 CHIP, 1/20W 47K OHM J
R169 76011102 CHIP, 1/20W 1K OHM J
R171 76011473 CHIP, 1/20W 47K OHM J
R172 76011162 CHIP, 1/20W 1.6K OHM J
R173 76011102 CHIP, 1/20W 1K OHM J
R174 76011473 CHIP, 1/20W 47K OHM J
R175 76011223 CHIP, 1/20W 22K OHM J
R176 76011473 CHIP, 1/20W 47K OHM J
R177 76011223 CHIP, 1/20W 22K OHM J
R178 76011103 CHIP, 1/20W 10K OHM J
R179 76011222 CHIP, 1/20W 2.2K OHM J
R180 76011473 CHIP, 1/20W 47K OHM J
R181 76011223 CHIP, 1/20W 22K OHM J
R182 76011162 CHIP, 1/20W 1.6K OHM J
R190 76011101 CHIP, 1/20W 100 OHM J
R191 76011330 CHIP, 1/20W 33 OHM J
R192 76011330 CHIP, 1/20W 33 OHM J
R217 76011104 CHIP, 1/20W 100K OHM J
R227 76366303 CARBON FILM, 1/6W 30K OHM J
R228 76011271 CHIP, 1/20W 270 OHM J
R229 76011271 CHIP, 1/20W 270 OHM J
R230 76011271 CHIP, 1/20W 270 OHM J
R301 76366163 CARBON FILM, 1/6W 16K OHM J
R305 76182025 METAL R ERX1FJ1R5H
R306 76366563 CARBON FILM, 1/6W 56K OHM J
R307 76366103 CARBON FILM, 1/6W 10K OHM J
R312 76552272 OXIDE METAL FILM, 1/2W 2.7K OHM J
R313 76366513 CARBON FILM, 1/6W 51K OHM J
R316 76011392 CHIP, 1/20W 3.9K OHM J
R317 76011392 CHIP, 1/20W 3.9K OHM J
R333 76531120 FUSIBLE, 1/2W 12 OHM J
R336 76383331 OXIDE METAL FILM, 2W 330 OHM J
R410 76011181 CHIP, 1/20W 180 OHM J
R411 76011561 CHIP, 1/20W 560 OHM J
R416 76019323 OXIDE METAL FILM, 5W 1.8K OHM J
R421 76011391 CHIP, 1/20W 390 OHM J
R430 76366103 CARBON FILM, 1/6W 10K OHM J
R431 76531120 FUSIBLE, 1/2W 12 OHM J
R432 76366202 CARBON FILM, 1/6W 2K OHM J
R433 76011182 CHIP, 1/20W 1.8K OHM J
R434 76552271 OXIDE METAL FILM, 1/2W 270 OHM J
R435 76011822 CHIP, 1/20W 8.2K OHM J
R437 76366682 CARBON FILM, 1/6W 6.8K OHM J
R442 76383331 OXIDE METAL FILM, 2W 330 OHM J
R447 76553472 OXIDE METAL FILM, 1W 4.7K OHM J
R448 76321228 OXIDE METAL FILM, 1/2W 0.22 OHM J
R479 76011101 CHIP, 1/20W 100 OHM J
Location Parts No. Description
No.
Location Parts No. Description
No.
All manuals and user guides at all-guides.com