Toshiba AW-SD150SBA User manual

SERVICE MANUAL
FULLY AUTOMATIC
WASHING MACHINE
AW–6'6%2
AW–S'6%$
FILE NO. %-
PRINTED IN THAILAND, -XQ., 20 S

– 1 –
CONTENTS
1. SPECIFICATIONS .................................................................................................................. 1
2. CAUTIONS FOR SAFETY ..................................................................................................... 2
3. CAUTIONS FOR MICROCOMPUTER OPERATION ............................................................. 4
4. TECHNICAL POINT ............................................................................................................... 5
5. INSTALLATION ....................................................................................................................... 8
6. SCHEMATIC DIAGRAM ......................................................................................................... 9
7. CHECKING PROCEDURES ................................................................................................ 10
8. DISASSEMBLY INSTRUCTIONS......................................................................................... 22
9. CHECK POINTS AFTER REPAIRING ................................................................................. 35
10. EXPLODED VIEWS AND PARTS LIST ................................................................................ 38
1. SPECIFICATIONS
Model
Wash
Spin
Water Level
Water Consumption
Motor Type
Water Pressure
Hot Water
Overall Dimension
Net Weight
Wash
Spin
AW-SD150SBA
50Hz : 70 - 150 rpm
50Hz : 760 rpm
High : 105 L, LOW : L
Regular cycle : 250 L
Capacitor Motor
0.03 ~ 1 Mpa
50 degrees C or less
W: 685 mm x D: 685 mm x H: 1088 mm
50 kg
1.0 kg
Power Source
Plug Type
Wash
Spin
Destination
Specifications are subject to change without notice.
230 - 240 V, 50Hz
33
W
W
Oman
Power Consumption
Revolution
Capacity
AW-SD150SBO
220 V, 50Hz
W
:
UAE
3P

– 2 –
2. CAUTIONS FOR SAFETY
• Please observe the following important notes on safety.
• The notes mean as follows.
Symbol Meaning
Indicates possibility of death or serious injury of a repair technician and a person
nearby through the misconducted work, or of a user by a defect of the product after
the work performed by the technician.
Indicates possibility of injury or physical damages* of a repair technician and a
person nearby through the misconducted work, or of a user by a defect of the
product after the work performed by the technician.
WARNING
CAUTION
∗Means secondary damages of property, furniture, domestic animal and pet.
Graphic symbols
Graphic Symbol Meaning
indicates a caution (including a warning).
Specific instruction is followed by a graphic or characters in or near .
Symbol left warns an electric shock.
indicated prohibition (act must not be conducted).
Specific instruction is followed by a graphic or characters in or near .
Symbol left warns not to disassemble.
indicates a forcing (act must be conducted).
Specific instruction is followed by a graphic or characters in or near .
Symbol left warns to unplug the power cord.
ELECTRIC SHOCK
DO NOT
DISASSEMBLE
UNPLUG
LAdvise the customer to keep children out of the work place.
Children may be injured with a tool or a disassembled part.
L Unplug the power cord for the work unnecessary to power on like disassembling.
Do not hold the plug by a wet hand.
Failing to unplug may cause an electric shock.
LUse the specified repair parts when repairing the product.
Otherwise, a malfunction or a defect may occur. Also, a short circuit, ignition or
other danger to the customer may occur.
WARNING
OUT OF CHILD
UNPLUG POWER
USE
REPAIR PARTS

– 3 –
WARNING
L After the end of working, measure insulation resistance between the charging part
(power cord plug) and the non-charging metallic part (ground) with an insulation
resistance meter (500 V) and check the resistance is 10 MΩor more.
Failing to check the insulation resistance may cause a short circuit, an electric
shock or other diseases to the customer.
LDo not modify the product.
An electric shock or ignition may occur.
LOnly a repair technician can disassemble and repair.
An electric shock, ignition or malfunction may cause injury.
L Use an exclusive 220 VAC/17A socket for the washing machine.
Otherwise, an electric shock or ignition may cause. Sharing the same socket with
other instrument causes heating of a branch socket and result in a fire.
LConnect the grounding wire.
Failing to do so may cause an electric shock when a short circuit occurs.
Consult an electric work shop or a sales shop.
LDo not install in a bath room or a place exposed to wind or rain.
An electric shock or a short circuit may cause a fire.
LDo not pour or immerse the electrical parts.
An electric shock or ignition may occur.
LWipe off the dust adhered to the plug of the power cord.
Dust may cause a fire.
LDo not put inflammable into the washing tub.
Do not put cloths stained with kerosene, gasoline, benzene, thinner, alcohol. etc. It may
causea a fire or explosion.
LDo not touch the laundry before the spin basket stops completely.
The laundry entangles your hand causing an injury even if the basket rotates slowly.
Pay special attention to children.
CHECK INSULATION
RESISTANCE
DO NOT MODIFY
DO NOT
DISASSEMBLE
AND REPAIR
USE EXCLUSIVE
SOCKET
CONNECT
GROUNDING WIRE
DO NOT USE
WET PLACE
DO NOT SPLASH
WATER
REMOVE DUST
DO NOT TOUCH
AVOID INFLAM-
MABLE

– 4 –
CAUTION
LAsk an electric work shop to install the product.
Install the product securely and safely according to the electrical equipment
technical standard and the wiring standard.
Incorrect work causes an electric shock and a fire.
LDo not pull the power cord when unplugging.
Hold the power plug to unplug.
An electric shock or short circuit may cause a fire.
LDo not insert your hand under the washing machine during operation.
There is a rotary part under the machine which may cause an injury.
LBefore starting washing, open the faucet and check that the water supply hose
joint is not loose and no water leaks.
The loose screw or hose joint may cause water leakage resulting in an unexpected damage.
INSTALL
CAREFULLY
DO NOT PULL
DANGER HAND
WATER LEAKAGE
3. CAUTIONS FOR MICROCOMPUTER OPERATION
When changing the cycles or procedures of the operation on the way, the operation will not be changed even if
the START/HOLD button is pushed.
When changing the cycles or the procedures of the operation, please turn off the power switch and set them
again.
When the power switch is not turned on, the operation is not performed even if the clock display appears.
(When the clock display appears on the display panel, it may lead misunderstanding to control the operation.
But the operation is not performed in this condition.)

– 5 –
4. Technical Points
One-Point Information
About operation switching by clutch mechanism
1. About Clutch Mechanism
Switch washing operation and spinning operation by
a sliding clutch mechanism. The sliding clutch is
operated by pulling and pushing back the clutch lever.
1) When washing operation is performed, the teeth
on the top of the clutch fit into the teeth of the
lock gear on the upper part of the product
(on cup assy side). Fig.3
2) When spinning operation is performed, the
teeth on the bottom of the clutch fit into the teeth
of the boss on the lower part of the product
(on rotor side). Fig.2
Cup assy Clutch lever
Rotor
Lock gear Clutch Switching lever
Fig.1 Clutch mechanism
Lock gear
Clutch Rotor
Lock gear
Clutch
Rotor
Fig.2 Clutch condition during spinning operation Fig.3 Clutch condition during washing operation

– 6 –
One-Point Information
2. About Operation Switching
Wash ASpin clutch switching
1Pull the drain valve. (Pull the clutch lever.)
2The pulsator rotates forwards while repeating small forward and reverse rotations.
3Clutch switching is completed when both the wash tub and the pulsator start rotating.
In the case where the clutch is not switched even after the clutch switching is attempted 4 times, fill the
wash tub with water again and fluff the laundry, then perform the same switching operation. If the clutch is
still not switched, the error Ec6 is displayed.
Sometimes, clutch switching operation is performed by filling the wash tub with water at the start of
spinning.
(See Page 2for details of Ec errors.)
Spin AWash clutch switching
1The drain valve returns. (The lever returns.)
2Spin tub makes small forward and reverse rotations.
3The spin tub makes large forward and reverse rotations at a low speed.
4Clutch switching is completed when only the pulsator starts rotating.
In the case where the clutch is not switched even after the clutch switching is attempted 6 times, fill the
wash tub with water and let it stand for 3 minutes, then perform the switching operation again. If the
clutch is still not switched, rotate the wash tub by 180 degrees and perform the same switching operation.
If the clutch is still not switched, the error Ec5 is displayed. (See Page 2for details of Ec errors.)
Note) If the washing operation was originally being performed, the clutch switching is not performed but
the washing operation starts immediately.
3. About operation of wash tub
When the power is
turned off during spin
process
Operation
Just as the current models, the wash tub does not rotate even if it is not turned
clockwise or counterclockwise direction. The wash tub stops at multiple
positions (at one of the 18 points for every 20 degrees)
Just as the current models, the wash tub rotates freely both in clockwise or
counterclockwise direction. When a long time (30 minutes) has elapsed, the
machine is switched to the clutch switching standby status.
After rotating in the reverse direction at the start of spinning, the main spinning
is performed. (This control is adopted from E-series.)
Just as the current models, brake is applied to stop rotation. When the rotation
stops, the clutch lever returns and the machine is switched to the clutch
switching standby status.
Process
Wash process & when
wash process is stopped
When spin process is
suspended.
(When the lid is opened
during spin process)
At the start of spinning
Forward rotation
Reverse rotation Time

–7 –
One-Point Information
About Concentrated Bubble Wash
1. Outline
Put the laundry in the basket and start the machine. The sensor will weigh clothes and begin flowing water.
1
The pulsator begins to revolve 6 seconds after startup under none-water situation, and clothes are
weighed.
2
)ORwing water starts. Put in detergent accorGLQJWRWKHUHIHUHQFHYDOXHWKURXJKHQWU\JDWHRI
"Washing Spinning Tub", followed by softening agent. Close the lid. Display of detergent amount.
■How to put detergent
Referring to the indicated detergent amount, put the
detergent into the detergent dispenser of the wash/spin tub.
Excessive detergent may lead to excessive suds or
insufficient rinsing.
If the water level is set to too low, some detergent may be
left in the dispenser.
In this case, put the detergent inside the wash/spin tub
around its peripheral.
∗There are 2 dispensers.
Choose more convenient one to put in the detergent.
•When changing the dispenser position
Turn on the power, set spin only while the lid is open, and then start the machine.
After “E21”is displayed, rotate the wash/spin tub manually to adjust the dispenser position. Then,
turn off the power.
3
The water level indicator will be lighted when flowing water ends by reaching the preset water level.
• When a chemical fiber, blending fiber or spreadsheet is washed, the water level may be a little bit low.
Adjust the water level by "WATER LEVEL" button.
Stirring starts during flowing water while washing and flowing water are executed simultaneously.
Times of flowing water differ depending onFORWKHVZHLJKWDQGULQVLQJIUH XHQF\
Washinging
Stirring during
flowing water
Stirring during
flowing water
Stirring during
flowing water

–8 –
One-Point Information
2. Operation Cycle
Example : At high water level
High
Water level
Low
Water
supply valve
Motor
Concentrated
Bubble
Cleaning
Indicator
Weight
sensor
Wash Process Drain
Agitation
Water
supply
Light Flash Light Off
Time scale
Washing load Number of levels of water supply and agitation
8.1 kg and above
1.1 ~ 8.0 kg 3 levels
Below 1.0 kg 2 levels
Number of levels of water supply and agitation vary depending on the washing load.
∗When increasing the number of rinsing for the reason that the tub has already been filled with water,
the above number of levels may become less.
∗Agitation varies depending on the washing load
∗If washing time (preset: 15minutes) is changed in the midst of wash process, agitating time in each level
becomes shorter.
4levels

–9 –
One-Point Information
About Linear Water Level
When “Standard”, “Soak”,“Memory”,"Heavy","Delicate" or "Softener" is set, the weight sensor automatically
sets the most suitable water level for the washing load on a linear basis to save water.
Setting is made based on the 4-levelled water level for manual setting. For example, when the detected
washing load is 5.0kg, the most suitable water level of 67.3L is automatically set by proportional calculation
between the first level of 82L for washing load of 7.0kg and the second level of 60L for washing load of
4.0kg. The display indicator for the lower water level, i.e., 60L for this example, turns on.
Manually set water level
1
2 82L 7.0Kg
3 60L 4.0Kg
4 36L 1.0Kg
2
.

4.0 5..
(L)
(KL)
Water level
Washing load
Water level of 36L is very low as the blade of the pulsator is not fully covered with water. However, this water
level is suitable for washing the washing load of 1.0kg or below.
It is not an abnormal level.
AW-SD1567\SH
1.0Kg
105L
Washing load

– 10 –
One-Point Information
Relation between oscillation frequency and water level
The table below shows the relation between oscillation frequency and water level.
Water level Water amount Oscillation frequency
Distance from the top edge of the
Reference water level
outer periphery of the pulsator
–
26.40kHz and above ––
– 26.05kHz – –
36L 25.10kHz 100±30 mm
60L 23.80kHz
82L 23.00kHz
100L 22.05kHz
No water
reset
Low 60L
Pulsator
High 105L
Med 82L
Very little 36L
End of the outer
periphery of the pulsator
<Reference Water Level>
105L 22.00kHz
High 100L
±30 mm

±30 mm
 5HIHUWRWKHILJXUHEHORZ
±15 mm

±15 mm


㩷㩷㪚㫆㫌㫉㫊㪼
㪮㪸㫋㪼㫉
㫃㪼㫍㪼㫃
㪁㪥㫆㫋㪼㪈
㪮㪼㫀㪾㪿㫋㩷㪻㪼㫋㪼㪺㫋㫀㫆㫅 㪮㪸㫋㪼㫉㩷㫊㫌㫇㫇㫃㫐 㪧㫉㪼㪄㪸㪾㫀㫋㪸㫋㫀㫆㫅 㪮㪸㫊㪿 㪩㪸㫍㪼㫃 㪛㫉㪸㫀㫅 㪪㫇㫀㫅 㪪㫋㫆㫇 㪙㫉㪸㫂㪼 㪮㪸㫋㪼㫉㩷㪽㫀㫃㫃㫀㫅㪾 㪪㫇㫀㫅 㪪㫋㫆㫇 㪙㫉㪸㫂㪼 㪮㪸㫋㪼㫉㩷㪽㫀㫃㫃㫀㫅㪾 㪪㫇㫀㫅 㪪㫋㫆㫇 㪙㫉㪸㫂㪼 㪮㪸㫋㪼㫉㩷㫊㫌㫇㫇㫃㫐 㪧㫉㪼㪄㪸㪾㫀㫋㪸㫋㫀㫆㫅 㪩㫀㫅㫊㪼 㪩㪸㫍㪼㫃 㪛㫉㪸㫀㫅 㪪㫇㫀㫅 㪪㫋㫆㫇 㪮㪸㫋㪼㫉㩷㫊㫌㫇㫇㫃㫐 㪧㫉㪼㪄㪸㪾㫀㫋㪸㫋㫀㫆㫅 㪩㫀㫅㫊㪼 㪩㪸㫍㪼㫃 㪛㫉㪸㫀㫅 㪪㫇㫀㫅 㪪㫋㫆㫇 㪙㫌㫑㫑㪼㫉
㪣㫀㫅㪼㪸㫉
㪸㫌㫋㫆㩷㫊㪼㫋㫋㫀㫅㪾
㩿㪊㪍㪣䌾㪈㪇㪌㪣㪀 䋨㪟㫀㪾㪿㩷㫎㪸㫋㪼㫉㩷㫃㪼㫍㪼㫃㩷㪺㫆㫅㪻㫀㫋㫀㫆㫅㩷㪀
㪣㫀㫅㪼㪸㫉
㪮㪸㫊㪿 㪸㫌㫋㫆㩷㫊㪼㫋㫋㫀㫅㪾
㩿㪊㪍㪣䌾㪈㪇㪌㪣㪀
㪣㫀㫅㪼㪸㫉
㪩㫀㫅㫊㪼 㪸㫌㫋㫆㩷㫊㪼㫋㫋㫀㫅㪾
㫆㫅㪼 㩿㪊㪍㪣䌾㪈㪇㪌㪣㪀
㫋㫀㫄㪼 㪁㪥㫆㫋㪼㪉
㪣㫀㫅㪼㪸㫉
㪩㫀㫅㫊㪼 㪸㫌㫋㫆㩷㫊㪼㫋㫋㫀㫅㪾
㫋㫎㫆 㩿㪊㪍㪣䌾㪈㪇㪌㪣㪀
㫋㫀㫄㪼㫊 㪁㪥㫆㫋㪼㪉
㪣㫀㫅㪼㪸㫉
㪩㫀㫅㫊㪼 㪸㫌㫋㫆㩷㫊㪼㫋㫋㫀㫅㪾
㫋㪿㫉㪼㪼 㩿㪊㪍㪣䌾㪈㪇㪌㪣㪀
㫋㫀㫄㪼㫊 㪁㪥㫆㫋㪼㪉
㪣㫀㫅㪼㪸㫉
㪩㫀㫅㫊㪼 㪸㫌㫋㫆㩷㫊㪼㫋㫋㫀㫅㪾
㪽㫆㫌㫉 㩿㪊㪍㪣䌾㪈㪇㪌㪣㪀
㫋㫀㫄㪼㫊 㪁㪥㫆㫋㪼㪉
㪪㫇㫀㫅 㫅㫀㫃
㫊㫋㪸㫋㫀㪺㩷㫉㫀㫅㫊㪼㩷 㩷㫊㫋㪸㫋㫀㪺㩷㫉㫀㫅㫊㪼㩷
㩿㫊㫌㫇㫇㫃㪼㫄㪼㫅㫋㪸㫃㫐㩷 㫆㫍㪼㫉㩷㪽㫃㫆㫎㩷㫉㫀㫅㫊㪼 㫆㫍㪼㫉㩷㪽㫃㫆㫎㩷㫉㫀㫅㫊㪼
㩷㩷㫎㪸㫋㪼㫉㩷㪽㫀㫃㫃㫀㫅㪾㪀
㪝㫆㫉㫎㪸㫉㪻
㫉㫆㫋㪸㫋㫀㫆㫅
㩿㩷㪚㪚㪮㪀
㪩㪼㫍㪼㫉㫊㪼
㫉㫆㫋㪸㫋㫀㫆㫅
㩿㩷㪚㪮㪀
㪥㫆㫋㪼㪈㩷㪑
㪥㫆㫋㪼䋲㩷㪑 㪮㪿㪼㫅㩷㩹㪮㪸㫊㪿㩹㩷㫀㫊㩷㫅㫆㫋㩷㫊㪼㫋㩷㪃㩷㫋㪿㪼㩷㫎㪸㫋㪼㫉㩷㫃㪼㫍㪼㫃㩷㫎㫀㫃㫃㩷㪸㫌㫋㫆㫄㪸㫋㫀㪺㪸㫃㫃㫐㩷㪹㪼㩷㫊㪼㫋㩷㫋㫆㩷㪿㫀㪾㪿㪅
䊶䇭㪠㫅㩷㫋㪿㪼㩷㪺㪸㫊㪼㩷㫎㪿㪼㫉㪼㩷㫋㪿㪼㩷㫇㫆㫎㪼㫉㩷㫀㫊㩷㫋㫌㫉㫅㪼㪻㩷㫆㫅㩷㩿㩷㫋㪿㪼㩷㫇㫆㫎㪼㫉㩷㪹㫌㫋㫋㫆㫅㩷㫀㫊㩷㫇㫉㪼㫊㫊㪼㪻㩷㪀㩷㪹㫌㫋㩷㫅㫆㩷㫆 㫇㪼㫉㪽㫆㫉㫄㪼㪻㪃㩷㫋㪿㪼㩷㫇㫆㫎㪼㫉㩷㫀㫊㩷㫋㫌㫉㫅㪼㪻㩷㫆㪽㪽㩷㫀㫅㩷㪈㪇㩷㫄㫀㫅㫌㫋㪼㫊㪅
㪣㫀㪻㩷㪣㫆㪺㫂
㪦㫌㫋㫆㫌㫋
㪪㫆㪽㫋㪼㫅㪼㫉㩷㫎㪸㫋㪼㫉
㫊㫌㫇㫇㫃㫐㩷㫍㪸㫃㫍㪼
㪤㫆㫋㫆㫉
㪛㫉㪸㫀㫅㩷㫍㪸㫃㫍㪼
㪪㫋㪸㫋㫀㪺㩷㫉㫀㫅㫊㪼㩷㪈 㪪㫋㪸㫋㫀㪺㩷㫉㫀㫅㫊㪼㩷㪉
㪩㫀㫅㫊㪼 㪪㫇㫀㫅
㪮㪸㫋㪼㫉㩷㪽㫃㫆㫎㩷㪻㪼㫋㪼㪺㫋㫀㫆㫅
㪮㪸㫊㪿
㪪㪿㫆㫎㪼㫉㩷㫉㫀㫅㫊㪼㩷㪈 㪪㪿㫆㫎㪼㫉㩷㫉㫀㫅㫊㪼㩷㪉
㪚㫆㫅㪻㪼㫅㫊㪼㪻
㪩㪼㪾㫌㫃㪸㫉
㪤㪼㫄㫆㫉㫐
㪮㪸㫋㪼㫉㩷㫊㫌㫇㫇㫃㫐㩷㫍㪸㫃㫍㪼
㪦㫅㪼㪄㪧㫆㫀㫅㫋㩷㩷㪠㫅㪽㫆㫉㫄㪸㫋㫀㫆㫅
㪮㪸㫊㪿㫀㫅㪾㩷㪧㫉㫆㪺㪼㫊㫊㩷㪚㪿㪸㫉㫋
– 11–
AW-SD150S Type 36L ~ 105L
peration is

㩷㩷㪚㫆㫌㫉㫊㪼
㪮㪸㫋㪼㫉
㫃㪼㫍㪼㫃
㪮㪼㫀㪾㪿㫋㩷㪻㪼㫋㪼㪺㫋㫀㫆㫅 㪮㪸㫋㪼㫉㩷㫊㫌㫇㫇㫃㫐 㪧㫉㪼㪄㪸㪾㫀㫋㪸㫋㫀㫆㫅 㪪㫆㪸㫂 㪩㪸㫍㪼㫃 㪛㫉㪸㫀㫅 㪪㫇㫀㫅 㪪㫋㫆㫇 㪙㫉㪸㫂㪼 㪮㪸㫋㪼㫉㩷㪽㫀㫃㫃㫀㫅㪾 㪪㫇㫀㫅 㪪㫋㫆㫇 㪙㫉㪸㫂㪼 㪮㪸㫋㪼㫉㩷㪽㫀㫃㫃㫀㫅㪾 㪪㫇㫀㫅 㪪㫋㫆㫇 㪙㫉㪸㫂㪼 㪮㪸㫋㪼㫉㩷㫊㫌㫇㫇㫃㫐 㪧㫉㪼㪄㪸㪾㫀㫋㪸㫋㫀㫆㫅 㪩㫀㫅㫊㪼 㪩㪸㫍㪼㫃 㪛㫉㪸㫀㫅 㪪㫇㫀㫅 㪪㫋㫆㫇 㪮㪸㫋㪼㫉㩷㫊㫌㫇㫇㫃㫐 㪧㫉㪼㪄㪸㪾㫀㫋㪸㫋㫀㫆㫅 㪩㫀㫅㫊㪼 㪩㪸㫍㪼㫃 㪛㫉㪸㫀㫅 㪪㫇㫀㫅 㪪㫋㫆㫇 㪙㫌㫑㫑㪼㫉
㪣㫀㫅㪼㪸㫉
㪸㫌㫋㫆㩷㫊㪼㫋㫋㫀㫅㪾
㩿㪊㪍㪣䌾㪈㪇㪌㪣㪀 䋨㪟㫀㪾㪿㩷㫎㪸㫋㪼㫉㩷㫃㪼㫍㪼㫃㩷㪺㫆㫅㪻㫀㫋㫀㫆㫅㩷㪀
㪣㫀㫅㪼㪸㫉 㩿㫆㫍㪼㫉㩷㪽㫃㫆㫎㩷㫉㫀㫅㫊㪼㪀 㩿㫆㫍㪼㫉㩷㪽㫃㫆㫎㩷㫉㫀㫅㫊㪼㪀
㪸㫌㫋㫆㩷㫊㪼㫋㫋㫀㫅㪾
㩿㪊㪍㪣䌾㪈㪇㪌㪣㪀 䋨㪟㫀㪾㪿㩷㫎㪸㫋㪼㫉㩷㫃㪼㫍㪼㫃㩷㪺㫆㫅㪻㫀㫋㫀㫆㫅㩷㪀
㪣㫀㫅㪼㪸㫉 㩿㪍㩷㫄㫀㫅㪀 㩿㪌㩷㫄㫀㫅㪀
㪸㫌㫋㫆㩷㫊㪼㫋㫋㫀㫅㪾
㩿㪊㪍㪣䌾㪈㪇㪌㪣㪀 䋨㪟㫀㪾㪿㩷㫎㪸㫋㪼㫉㩷㫃㪼㫍㪼㫃㩷㪺㫆㫅㪻㫀㫋㫀㫆㫅㩷㪀
㩷㩷㪚㫆㫌㫉㫊㪼
㪮㪸㫋㪼㫉
㫃㪼㫍㪼㫃
㪮㪼㫀㪾㪿㫋㩷㪻㪼㫋㪼㪺㫋㫀㫆㫅 㪮㪸㫋㪼㫉㩷㫊㫌㫇㫇㫃㫐 㪧㫉㪼㪄㪸㪾㫀㫋㪸㫋㫀㫆㫅 㪮㪸㫊㪿 㪩㪸㫍㪼㫃 㪛㫉㪸㫀㫅 㪪㫇㫀㫅 㪪㫋㫆㫇 㪙㫉㪸㫂㪼 㪮㪸㫋㪼㫉㩷㫊㫌㫇㫇㫃㫐 㪧㫉㪼㪄㪸㪾㫀㫋㪸㫋㫀㫆㫅 㪩㫀㫅㫊㪼 㪩㪸㫍㪼㫃 㪛㫉㪸㫀㫅 㪪㫇㫀㫅 㪪㫋㫆㫇 㪮㪸㫋㪼㫉㩷㫊㫌㫇㫇㫃㫐 㪧㫉㪼㪄㪸㪾㫀㫋㪸㫋㫀㫆㫅 㪩㫀㫅㫊㪼 㪩㪸㫍㪼㫃 㪛㫉㪸㫀㫅 㪪㫇㫀㫅 㪪㫋㫆㫇 㪙㫌㫑㫑㪼㫉
㪣㫀㫅㪼㪸㫉
㪸㫌㫋㫆㩷㫊㪼㫋㫋㫀㫅㪾
㩿㪊㪍㪣䌾㪈㪇㪌㪣㪀 䋨㪟㫀㪾㪿㩷㫎㪸㫋㪼㫉㩷㫃㪼㫍㪼㫃㩷㪺㫆㫅㪻㫀㫋㫀㫆㫅㩷㪀
㪣㫀㫅㪼㪸㫉 㩿㪍㩷㫄㫀㫅㪀 㩿㪊㩷㫄㫀㫅㪀
㪸㫌㫋㫆㩷㫊㪼㫋㫋㫀㫅㪾
㩿㪊㪍㪣䌾㪍㪇㪣㪀
㩿㫆㫍㪼㫉㩷㪽㫃㫆㫎㩷㫉㫀㫅㫊㪼㪀 㩿㫆㫍㪼㫉㩷㪽㫃㫆㫎㩷㫉㫀㫅㫊㪼㪀
㪈㪇㪌㪣
㪮㪸㫋㪼㫉㩷㫊㫌㫇㫇㫃㫐 㪮㪸㫊㪿 㪪㫇㫀㫅㩷㩷㩷㫉㪼㫄㪸㫀㫅㫀㫅㪾㩷㫎㪸㫋㪼㫉 㪛㫉㪸㫀㫅 㪪㫇㫀㫅 㪮㪸㫋㪼㫉㩷㫊㫌㫇㫇㫃㫐 㪩㫀㫅㫊㪼 㪪㫇㫀㫅㩷㩷㩷㫉㪼㫄㪸㫀㫅㫀㫅㪾㩷㫎㪸㫋㪼㫉 㪛㫉㪸㫀㫅 㪪㫇㫀㫅 㪙㫌㫑㫑㪼㫉
㪮㪸㫋㪼㫉㩷㫊㫌
㫇㫇
㫃
㫐
㩷㫍㪸㫃㫍㪼
㩿㪟㫀㪾㪿㩷㪂㩷㪊㪇㩷㫊㪼㪺㪀 㩿㪟㫀㪾㪿㩷㪂㩷㪊㪇㩷㫊㪼㪺㪀
㪝㫆㫉㫎㪸㫉㪻 㩿㪍㩷㫄㫀㫅㪀
㫉㫆㫋㪸㫋㫀㫆㫅
㩿㩷㪚㪚㪮㪀
㪩㪼㫍㪼㫉㫊㪼
㫉㫆㫋㪸㫋㫀㫆㫅
㩿㩷㪚㪮㪀
㪛㫉㪸㫀㫅㩷㫍㪸㫃㫍㪼
㪘㫌㫋㫆㩷
㫇
㫆㫎㪼㫉㩷㫆㪽㪽
㪪㫋㪸㫋㫀㪺㩷㫉㫀㫅㫊㪼㩷㪈 㪪㫋㪸㫋㫀㪺㩷㫉㫀㫅㫊㪼㩷㪉
㪩㫀㫅㫊㪼 㪪㫇㫀㫅㪮㪸㫊㪿
㪪㪿㫆㫎㪼㫉㩷㫉㫀㫅㫊㪼㩷㪈 㪪㪿㫆㫎㪼㫉㩷㫉㫀㫅㫊㪼㩷㪉
㪮㪸㫊㪿
㪛㪼㫃㫀㪺㪸㫋㪼
㪪㫇㪼㪼㪻
㪮㪸㫋㪼㫉㩷㪽㫃㫆㫎㩷㪻㪼㫋㪼㪺㫋㫀㫆㫅
㪪㫆㪸㫂
㪟㪼㪸㫍㫐㩷㫎㪸㫊㪿
㪮㪸㫊㪿 㪪㫇㫀㫅
㪪㫋㪸㫋㫀㪺㩷㫉㫀㫅㫊㪼㩷㪈 㪪㫋㪸㫋㫀㪺㩷㫉㫀㫅㫊㪼㩷㪉
㪤㫆㫋㫆㫉
㪪㫆㪸㫂
㪦㫌㫋㫇㫌㫋
㪩㫀㫅㫊㪼
㪙㫃㪸㫅㫂㪼㫋
㪮㪸㫋㪼㫉㩷㪽㫃㫆㫎㩷㪻㪼㫋㪼㪺㫋㫀㫆㫅
㪪㫆㪽㫋㪼㫅㪼㫉
㪦㫅㪼㪄㪧㫆㫀㫅㫋㩷㩷㪠㫅㪽㫆㫉㫄㪸㫋㫀㫆㫅
㪪㫆㪸㫂㩷䊶㩷㪟㪼㪸㫍㫐㩷㫎㪸㫊㪿㩷䊶㩷㪛㪼㫃㫀㪺㪸㫋㪼㩷㩷㪚㫆㫌㫉㫊㪼
㪪㫆㪽㫋㪼㫅㪼㫉㩷䊶㩷㪪㫇㪼㪼㪻㩷䊶㩷㪙㫃㪸㫅㫂㪼㫋㩷㪚㫆㫌㫉㫊㪼
㪫㫌㪹㩷㪚㫃㪼㪸㫅㫀㫅㪾㩷㩷㪚㫆㫌㫉㫊㪼
– 12–

Through setting of the SUPER SPIN DRY for 30 minutes, you can vapor the water contained in clothes, thus shorten
their indoor drying time. In addition, you can basically dry sports wear, chemical fiber or blending fiber by setting
SUPER SPIN DRY for 60 minutes (less than 3 kg).
•The hand touch differs depending on the type, weight of clothes, room temperature and moisture. Clothes will be cold due to air
drying process, so they may produce a hand touch feeling like the wet ones.
When you need to dry clothes or shorten their indoor drying time.
SUPER SPIN DRY
1 time
2 times
3 times
4 times
5 times
6 times
“REGULAR” course for CONDENSED BUBBLE
“REGULAR” course for CONDENSED BUBBLE
“REGULAR” course for CONDENSED BUBBLE
None
None
None
30 minutes
60 minutes
90 minutes
30 minutes
60 minutes
90 minutes
Washing SUPER SPIN DRY
What is the SUPER SPIN DRY?
This is a course which discharge wet air through the high-speed revolving of the washing-spinning tub, thus
vapor the water carried by the clothes.
Stirring High-speed revolving
Repeatedly
: Stir for every 15 minutes to unravel the clothes. Stirring may not be necessary, depending on the weight of the clothes.
LClothes prohibited for the SUPER SPIN DRY
•Since the SUPER SPIN DRY needs a long time for high-speed revolving, and unravel clothes every 15 minutes,
the following articles are not allowed for the process:
• Clothes with unstable color
• Creasing-prone clothes (such as frock, or 100% cotton shirt)
• Deformation-prone clothes
• Water-tight clothes
• Quilt and blanket
LMethod of using SUPER SPIN DRY button
(Ex.) When the “REGULAR” course of the “CONDENSED BUBBLE” is being executed
Press the “SUPER SPIN DRY” to select processing time according to the following sequence or select
SUPER SPIN DRY only. Please press the button for at least 4 times, when you select
SUPER SPIN DRY only.
SUPER SPIN DRY
– 13–

One-Point Information
AboutTub Dry
1. Outline
B y performing"tub dry" operation after w ashing is completed, humidity ins ide the was h/spin tub can be
removed and growth of black mold can be reduced.
2. Process
D ry up the re ma ining wa te r by high- s pe ed rota tion of wa s h/s pin tub for a pprox ima te ly 3 0 minute s .
P e rfor m this ope ra tion a fte r re mov ing a ll the c lothe s in the tub to e mpty the tub.
3. Panel operation
Tub rota tion a t high s pe e d(30 min)
Forward
rota tion
Motor
Reverse
rota tion
(30 min)
1 minute
Operation time is 30 minutes, which cannot be changed.
Tub dry
Buzzer
(CCW)
(CW)
Output
Run "TUB DRY" after was hing is finis hed, to prevent
mildew by removing the mois ture of the tub. P lea s e run
the course once a week.
P lease do not add clothes during the course.
1Power on, and press the
SUPER
SPIN DRY
button 4 times .
2Clos e the lid and press the button.
H igh- s pe ed revolving for a bout 3 0 minute s c a n dr y the
washing-spinning tub through air intaking and revolving
the puls a tor.
Tips
Mildew of Washing-S pinning tank occurs depending on the environment.
Once mildew occurs, it can not be removed by "TUB DRY" process. Therefore, it is recommended to run "TUB DR Y "
and "TUB CLEAN" regularly.
– 14–

One-Point Information
About Weight S ens or and S uitable Detergent
Amount Guide
( Itis described as "Washing load
sens or" in the ins truction manual.)
B e fore the wa te r s upply, rota te the puls a tor for a pproxima te ly 6 s e c onds to de te ct the loa d onto the motor
by the number of rota tion of the motor. T his is performe d to judge the wa s hing loa d to de cide wa ter leve l
a nd dis play the mos t s uita ble de te rge nt a mount to be put.
Deterge nt a mount is dis played by how many s poons of compa ct de te rgent to be us ed whe n us ing the
spoon provided.
( T he c a lc ula tion is ba s e d on the a s s umption tha t 1 s poonful of de te rge nt is for 55L of wa te r. )
Deterge nt amount for "Dry" cours e will be dis played by how many caps of neutral detergent to be put.
( T he c a lc ula tion is ba s e d on the a s s umption tha t 2 c a ps of ne utra l de te rge nt is for 3 0L of wa te r. )
T he wa te r leve l is a utoma tic a lly s e t a c cording to the de te rge nt a mount. H oweve r, the wa ter le ve l may be
a djus te d by the following me thod if the us e r fe els tha t a utoma tic a lly s e t wa te r le ve l is too high or too low.
When adjus ting automatic ally s et water level
T he wa te r leve l is a utoma tic a lly s e t a c cording to the de te rge nt a mount. H oweve r, the wa ter le ve l may be
a djus te d by the following me thod if the us e r fe els tha t a utoma tic a lly s e t wa te r le ve l is too high or too low.
Once a s etting is made, it will be s tored in the memory.
While press ing the press the power . B uzzer beeps . Water level indicator turns on.
(Auto power ON/OFF)
To lowe r the wa te r level
Press to a djus t
To raise the water level
Press to a djus t
Press twice. Press once.
(Decrease approx. 20L.) (Decrease approx.10L.)
Press once. Press twice.
(Increase approx. 10L.)(Increase approx. 20L.)
Turn the P OW E R off. (F inis hed adjus ting)
– 15–

– 16 –
One-Point Information
About Static Rinse Mode
1. “Static rinse” mode
There is a mode to change from “shower rinse” to “static rinse” mode by invisible button operation.
Use this mode for users who have a problem in “white rinsing water” or those who want longer rinsing.
(1) Applicable course
Concentrated standard, standard, soak and memory
(2) Mode setting method
1 of shower rinse becomes 1 of static rinse.
Rinse cycle becomes same as the case where bath water is used until rinse process.
1
Turn on the power.
2
Press button for 3 seconds. The setting completes
in approximately 5 seconds when the buzzer beeps.
Turn off the power.
•To return to shower rinse mode, perform the above
operation again. When the setting to shower rinse
completes, the buzzer beeps.
•Once the setting is made, it will be stored in the memory.
•The setting method for the past models, i.e., turn on the power while pressing “RINSE” + “COURSE”
can also be used.
(3) Rinse cycle
“Shower rinse” becomes “Static rinse” as shown in the table below.
Press the power button, then
Press for 3 seconds.
Display Rinse Cycle
1 rinse Static
1 rinse + overflow
overflow rinse
Static
2 rinse + Shower overflow
overflow rinse
3 rinse Shower Shower Static
3 rinse + Shower Shower overflow
overflow rinse
4 rinse Shower Shower Static
4 rinse + Shower Shower overflow overflow
overflow rinse
Static Rinse Cycle
Static
overflow
Static
overflow
Static
overflow
Static Static
overflow overflow
Static
Static
Static
Static
Static
Static
Static
Static
Static
Static
Static
2 rinse Shower

One-Point Information
Water Flow Power
How to choos e the water flow power
The water flow power during rinsing cannot be changed.
The water flow power can be adjusted only any of
"REGULAR" and "MEMERY" is selected.
Clothes should not be washed by strong water flow power.
with the wa te r flow power pre s et.
When the water level rea ches to a des ignated level, the
water flow power will be indicated. S uch indication will be
repeated in the following order. T his means the operation is
being done under the water flow power preset.
E xample (S tandard water flow power)
Key opera tion Dis play S ituation
Tu rn o n the powe r. S ta nda rd wa te r flow
(Default)
Press the When you need to
button once. wash rather strongly.
Press the When you need to
button twic e. wa s h s trongly.
Press the When you need to
button three times . wa s h s oftly.
Press the When you need to
button four time s . wa s h ra the r s oftly.
HI
LO
HI
LO
HI
LO
HI
LO
HI
LO
HI
LO
HI
LO
HI
LO
HI
LO
Press button to choos e the water flow power according to your needs s uch as what to be
was hed or dirtiness level.
When you need to change the water flow power during operation
Press the button to hold the operation.
T he water flow power will be gradually increased, and then be decreas ed. When you need to wash sensitive
clothes s oftly, hold the operation. Otherwise, s uch clothes may be damaged.
Press the button to choos e the water flow power.
Press the button again.
T he water flow power will be cha nged during the operation when you select more than one levels of water.
1
2
3
When the "MEMORY" mode is set, the operation will start
– 17–

– 18 –
One-Point Information
CHILD PROOF mode
This model is equipped with CHILD PROOF mode. After this mode is set to ON, the lid can be locked so that children should
not fall into washing-spining tub during washing or drying. If you find the accident such as children’s falling into the wash tub,
please take necessary safety action urgently.
If there are small children who require attention, set this mode ON.
WARNING: Pay attention to small children. Do not leave the lid open. Do not leave the washer filled with water. Never allow
children to look into the basket or play around the washer. Do not place the stand or box etc. near the washer.
HOW TO USE CHILD PROOF MODE
Press the button, then the washing machine begins operating, follow the instruction below:
Hold down the button, press the button once again.
•A buzzer will sound and the CHILD PROOF mode indicator will be activated.
Once the CHILD PROOF mode is set, it is stored in memory.
Canceling the CHILD PROOF mode
Hold down the button, press the button once again.
•A buzzer will sound and the CHILD PROOF mode indicator will be canceled.
Once the CHILD PROOF mode can be canceled even during the operation.
LCannot add detergent while child proof mode. The lid lock is activated.
LIf accident occur when strongly pull up lid when lid lock in child proof mode operate. The buzzer will be sound and operation
will stop. Subsequently if that state persists about 5 seconds, it will be detected as an alarm and water will be drained.
CHILD PROOF MODE (if you have small children)
LID LOCK
Instruction: Do not open the lid while lights up. (The lid may be damaged.)
At the end of washing, the lid will be automatically locked.
When you need to cancel the lid lock
LDuring operation
Press the button to hold the operation.
When lights out, the lid can be open.
LWhile the power is off
Turn the power on. When lights out, the lid can be open.
(When the power is turned off or shut down during operation, the lid will be automatically locked.)
ON
OFF

– 1–
: If Lid Lock problem, wash lid assy cannot open.
One-Point Information
About Lid Lock
How to do?
1) Take off top cover cap of both side by lift up of
lid 1 & lid 2 at center position and use small minus
driver for open cap.
(Photo. 1 and Photo. 2)
2) Take off screw and then remove top cover deco
of both side(Right & Left side).
(Photo. 3)
3) Take off panel deco by pushing slide-up by hand.
(Photo. 4)
4) Take off 4 screws on control panel and then lift-up
(Photo. 5)
5) Move control panel assy to left side for lid lock
(Photo. 6)
move out from lid hook.
12
3
4
56
Note 1) Becareful lead wire unit.
Caution : Before take off must beUnplugfor prevent
electric shock.