TOTALINE P374-1500 User manual

DIGITAL THERMOSTAT
MODEL P374-1500
Installation
Instructions
Replacement Components Division Carrier Corporation 7/99
TOTALINE
MULTI-STAGE PROGRAMMABLE
HEAT
PUMP
DUAL
FUEL
3 HEAT - 2 COOL
67
70
HEAT
COOL
AUTO
o
o
Am
6:03
68
Su

Table Of Contents
PREPARATION
REMOVE OLD THERMOSTAT
INSTALL BACKPLATE & WIRE
WIRING DIAGRAMS
CALIBRATION
TEST OPERATION
TROUBLESHOOTING
Page 1
Model No. P374-1500
CAUTION Follow Installation Instructions carefully.
DISCONNECT POWER TO THE HEATER -
AIR CONDITIONER BEFORE REMOVING
THE OLD THERMOSTAT AND INSTALLING
THE NEW THERMOSTAT. WARNING
2
3
4
5
8
10
9
Replacement Components Division - Carrier Corporation
This device complies with Part 15 of the FCC rules.
Operation is subject to the following 2 conditions:
(1) This device may not cause harmful interference,
and (2) This device must accept any interference
received, including interference that may cause
undesired operation.

Proper installation of the thermostat will be
accomplished by following these step
by step instructions. If you are unsure
about any of these steps, call a qualified
technician for assistance.
Assemble tools as shown below.
Flat Blade
Screwdriver
Wire cutter
& Stripper
Drill with 3/16
inch Drill Bit
(when not using
j-box)
Make sure your Heater/Air Conditioner
is working properly before beginning
installation of the thermostat.
Carefully unpack the thermostat.
Save the screws, wall anchors, and
instructions.
STEP #1
PREPARATION
Page 2
67
70
HEAT
COOL
AUTO
o
o
Am
6:03
68
Su
67
70
HEAT
COOL
AUTO
o
o
Am
6:03
68
Su
67
70
HEAT
COOL
AUTO
o
o
Am
6:03
68
Su
67
70
HEAT
COOL
AUTO
o
o
Am
6:03
68
Su

Turn off the power to the Heating/Air
Conditioning system at the main fuse
panel. Most residential systems have
a separate breaker for disconnecting
power to the furnace.
Remove the cover of the old thermostat.
If it does not come off easily check for
screws.
Loosen the screws holding the thermostat
base or subbase to the wall, and lift away.
Disconnect the wires from the old
thermostat. Tape the ends of the wires
as you disconnect them, and mark them
with the letter of the terminal for easy
reconnection to the new thermostat.
STEP #2
REMOVE OLD THERMOSTAT
Page 3
Keep the old thermostat for reference
purposes, until your new thermostat is
functioning properly.
67
70
HEAT
COOL
AUTO
o
o
Am
6:03
68
Su
67
70
HEAT
COOL
AUTO
o
o
Am
6:03
68
Su
67
70
HEAT
COOL
AUTO
o
o
Am
6:03
68
Su
67
70
HEAT
COOL
AUTO
o
o
Am
6:03
68
Su
67
70
HEAT
COOL
AUTO
o
o
Am
6:03
68
Su

STEP #3
INSTALL BACKPLATE & WIRE
Page 4
If the terminal designations on your old
thermostat do not match those on the
new thermostat, refer to the chart below,
or the wiring diagrams that follow.
Remove the backplate connector from the
rear of the thermostat. Attach it to the wall.
Install wires as directed below. When
finished, snap thermostat on to backplate.
Wire from the
old thermostat
terminal marked Function
Install on the
new thermostat
connector marked
G or F Fan G
Y1, Y or C Compressor Y1
W1,O,B
PowerRh, R, M, Vr, A R
C
O/B
C
Common
Rev. Valve
Y2 Y2
W2
W
W2
W3
2nd Stage Comp.
2nd Stage Heat
3rd Stage Heat
RS+5 RS+5
Remote Sensor +5vdc
RS RS
Remote Sensor Signal
RS G RS G
Remote Sensor Ground
67
70
HEAT
COOL
AUTO
o
o
Am
6:03
68
Su
67
70
HEAT
COOL
AUTO
o
o
Am
6:03
68
Su

Sample Wiring Diagrams
Page 5
R
C
G
Y1
Y2
W1
W2
W3
O
E
L
R
RS1
RS GND
RS+5
C
G
Y1
Y2 W1
W2W3
O
24 vac common
24 vac return
fan relay
1st Stage compressor
Reversing valve
2nd stage heat circuit (often electric)
3nd stage heat circuit
7 Wire, 1 Stage Cooling, 3 Stage Heat, Heat Pump
Most residential split and package heat pumps
with auxiliary heat
Thermostat
Remote Sensor
Wireless or
Hard wired
RED
BLACK
WHITE

Sample Wiring Diagrams
Page 6
Dual Fuel
R
C
G
Y1
Y2
W1
W2
O
E
L
R
RS1
RS GND
RS+5
C
G
Y1
Y2 W1
W2W3
W
Furnace
O
24 vac common
24 vac return
fan relay
1st Stage compressor
Reversing valve
2nd stage heat circuit (often electric)
7 Wire, 1 Stage Cooling, 2 Stage Heat, Heat Pump with 2nd fuel source Furnace
Most residential split and package heat pumps
with auxiliary heat
Thermostat
Remote Sensor
Wireless or
Hard wired
RED
BLACK
WHITE

Sample Wiring Diagrams
Page 7
R
C
G
Y1
Y2
W1
W2
O
E
L
RC
G
Y1
Y2 W1
W2
O
24 vac common
24 vac return
fan relay
1st Stage compressor
reversing valve
No auxiliary heat, residential Heat Pumps ,
split systems & package units
5 Wire, 1 Stage Cooling, 1 Stage Heat - Heat Pump*
Thermostat
R
C
G
Y1
Y2
W1
W2
O
E
L
RC
G
Y1
Y2 W1
W2
O
24 vac common
24 vac return
fan relay
1st Stage compressor
2nd Stagecompressor
1st stage heat circuit
2nd stage heat circuit
7 Wire, 2 Stage Cooling, 2 Stage Heat, Heat Pump
Most residential split and package heat pumps
with auxiliary heat
Thermostat

Sample Wiring Diagram
Calibration
Page 8
Every thermostat is calibrated before it leaves the factory.
Under normal circumstances there will never be a need to
recalibrate the thermostat again.
To accommodate special needs, the thermostat may be recalibrated
following these steps:
1. While holding the mode button in, press the down button for
2 seconds. After all the icons in the display appear, release
the buttons.
2. Press the mode button.
3. Press the up or down buttons until the flashing number
equals the current room temperature.
4. Press the mode button to return to normal operation.

STEP #4
TEST OPERATION
Page 9
Press the MODE button repeatedly until
the HEAT icon appears on the display.
Press the up/down buttons until the set
temperature is 10 degrees above room
temperature. The furnace should turn on.
Press the MODE button repeatedly until
the COOL icon appears on the display.
Press the up/down buttons until the set
temperature is 10 degrees below room
temperature. The air conditioner should
turn on. NOTE: Most equipment has a
time delay of 5 minutes between cool
cycles. This feature is defeatable on the
thermostat. Consult the Owner's Manual
under Setup, cycles per hour.
Turn the power on to the Heating/Air
Conditioning system.
67
70
HEAT
COOL
AUTO
o
o
Am
6:03
68
Su
67
70
HEAT
COOL
AUTO
o
o
Am
6:03
68
Su
67
70
HEAT
COOL
AUTO
o
o
Am
6:03
68
Su

TROUBLESHOOTING
Page 10
SYMPTOM: The HVAC equipment does not
attempt to turn on.
CAUSE: The compressor timer lockout may
prevent the air conditioner from
turning on, for a period of time.
REMEDY: Consult the Owner's Manual in
the Setup section to defeat the
cycles per hour and compressor
timeguard.
SYMPTOM: The display is blank.
CAUSE: Lack of proper power.
REMEDY: Make sure power is turned on to
the furnace and 24vac between R& W.
If Cis used, 24vac between R& C.
67
70
HEAT
COOL
AUTO
o
o
Am
6:03
68
Su
67
70
HEAT
COOL
AUTO
o
o
Am
6:03
68
Su
P/N 88-119
4Z95
C
c
F
FOR HOME OR OFFICE USE
Tested to Comply
with FCC Standards
Dual Fuel P374-1500