TOTALINE Deluxe 1H User manual

Totaline®Deluxe 1H/1C and 3H/2C
Touchscreen Programmable P340 Series Thermostats
® U.S. Registered Trademark.
All rights reserved.
Installation
Guide
570-219
69-2268-03
System Types
• Gas,oil,orelectricheatwithair
conditioning
• Warmair,hotwater,highefficiency
furnaces,heatpumps,steam,gravity
• Heatonly—two-wiresystems,power
toopenandclosezonevalves(Series
20),andnormallyopenzonevalves
• Heatonlywithfan
• Coolonly
• 750mVheatingsystems
This manual covers the following models
• P340-1110:For1Heat/1Coolsystems
• P340-1320:Forupto2Heat/2Coolheat/coolsystemsorupto3Heat/2
CoolHeatPumpSystems
Need Help?
Visitwww.Totaline.com
ThisthermostatcontainsaLithiumbatterywhichmaycontainPerchloratematerial.
PerchlorateMaterial—specialhandlingmayapply,
Seewww.dtsc.ca.gov/hazardouswaste/perchlorate

Installation Guide
69-2268—03 2 570-219
M29130
WALL OPENING
WALL ANCHORS (2)
(PROVIDED WITH
THERMOSTAT)
WALL
DRILLED
HOLES (2)
MOUNTING
SCREWS (2)
WIRE
Wallplate installation
1. Separatewallplatefromthermostat.
2. Mountwallplateasshownbelow.
MERCURY NOTICE
Ifthisproductisreplacingacontrolthatcontainsmercuryinasealedtube,donot
placetheoldcontrolinthetrash.Contactyourlocalwastemanagementauthorityfor
instructionsregardingrecyclingandproperdisposal.
CAUTION: ELECTRICAL HAZARD
Cancauseelectricalshockorequipmentdamage.Disconnectpowerbefore
beginning installation.
Drill3/16”holesfordrywall.
Drill7/32”holesforplaster.
Must be installed by a trained, experienced technician
• Readtheseinstructionscarefully.Failuretofollowtheseinstructions
candamagetheproductorcauseahazardouscondition.
M29131
Grasptopand
bottomofwallplate
andpulltoremove
fromthermostat.

P340 Series
570-219 3 69-2268—03
M29128
–
+–
+
–
+
For24VACprimarypower,connectcommon
sideoftransformerto“C”terminal.
Insertsuppliedbatteriesfor
primaryorbackuppower.
Power options
Pushexcesswirebackintothewallopening.Plug
wallopeningwithnon-flammableinsulation.
Removefactory-installedjumper
onlyfortwo-transformersystems.
Conventional Terminal Letters:
R Heatingpower.Connecttosecondarysideof
heatingsystemtransformer.
Rc Coolingpower.Connecttosecondary
sideofcoolingsystemtransformer.
C Commonwirefromsecondarysideof
coolingtransformer(if2transformers).
W 1ststageheatrelay.
W2 2ndstageheatrelay.
Y 1ststagecompressorcontactor.
Y2 2ndstagecompressorcontactor.
G Fanrelay.
S1 Optionaloutdoororremotesensor.
S2 Optionaloutdoororremotesensor.
Heat Pump Terminal Letters:
R Heatingpower.Connecttosecondary
sideofheatingsystemtransformer.
Rc Coolingpower.Connecttosecondary
sideofcoolingsystemtransformer.
C Commonwirefromsecondarysideof
coolingsystemtransformer.
Y 1ststagecompressorcontactor.
Y2 2ndstagecompressorcontactor.
Aux Auxiliaryheatrelay.
G Fanrelay.
E Emergencyheatrelay.
L Heatpumpreset(poweredcontinuously
whenSystemissettoEmHeat;system
monitorwhensettoHeat,CoolorOff).
O/B Changeovervalveforheatpumps.
S1 Optionaloutdoororremotesensor.
S2 Optionaloutdoororremotesensor.
Terminal Designations Shadedareasbelowapplyonly to P340-1320.
M28654
Wiring
M28653
M28655

Installation Guide
69-2268—03 4 570-219
Wiring guide—conventional systems
Wiring
1H/1C System (1 transformer)
Rc Power[1]
R [R+Rcjoinedbyjumper]
W Heatrelay
Y Compressorcontactor
G Fanrelay
C 24VACcommon[3]
S1 Optionaloutdoor/remotesensor
S2 Optionaloutdoor/remotesensor
Heat Only System
Rc Power[1]
R [R+Rcjoinedbyjumper]
W Heatrelay
C 24VACcommon[3]
S1 Optionaloutdoor/remotesensor
S2 Optionaloutdoor/remotesensor
Heat Only System (Series 20)
Rc [R+Rcjoinedbyjumper]
R Series20valveterminal“R”[1]
W Series20valveterminal“B”
Y Series20valveterminal“W”
C 24VACcommon[3]
S1 Optionaloutdoor/remotesensor
S2 Optionaloutdoor/remotesensor
2H/2C System (1 transformer)
Y2 Coolrelay2
W2 Heatrelay2
Rc Power[1]
R [R+Rcjoinedbyjumper]
W Heatrelay1
Y Coolrelay1
G Fanrelay
C 24VACcommon[3]
S1 Optionaloutdoor/remotesensor
S2 Optionaloutdoor/remotesensor
1H/1C System (2 transformers)
Rc Power(coolingtransformer)[1,2]
R Power(heatingtransformer)[1,2]
W Heatrelay
Y Compressorcontactor
G Fanrelay
C 24VACcommon[3,4]
S1 Optionaloutdoor/remotesensor
S2 Optionaloutdoor/remotesensor
Heat Only System With Fan
Rc Power[1]
R [R+Rcjoinedbyjumper]
W Heatrelay
G Fanrelay
C 24VACcommon[3]
S1 Optionaloutdoor/remotesensor
S2 Optionaloutdoor/remotesensor
Cool Only System
Rc Power[1]
R [R+Rcjoinedbyjumper]
Y Compressorcontactor
G Fanrelay
C 24VACcommon[3]
S1 Optionaloutdoor/remotesensor
S2 Optionaloutdoor/remotesensor
2H/2C System (2 transformers)
Y2 Coolrelay2
W2 Heatrelay2
Rc Power(coolingtransformer)[1,2]
R Power(heatingtransformer)[1,2]
W Heatrelay1
Y Coolrelay1
G Fanrelay
C 24VACcommon[3,4]
S1 Optionaloutdoor/remotesensor
S2 Optionaloutdoor/remotesensor
See[notes]below
 [1] Powersupply.Providedisconnectmeansandoverloadprotectionasrequired.
 [2] Removejumperfor2-transformersystems.
 [3] Optional24VACcommonconnection.
 [4] Commonconnectionmustcomefromcoolingtransformer.
Shadedareasbelowapplyonly to P340-1320.

P340 Series
570-219 5 69-2268—03
1H/1C Heat Pump (no auxiliary heat)
Rc Power[1]
R [R+Rcjoinedbyjumper]
O/B Changeovervalve[5]
Y Compressorrelay
G Fanrelay
C 24VACcommon[3]
S1 Optionaloutdoor/remotesensor
S2 Optionaloutdoor/remotesensor
2H/1C Heat Pump (with auxiliary heat)
L Equipmentmonitor[6,7]
E Emergencyheatrelay[8]
Aux Auxiliaryheatrelay(Heat2)[8]
Rc Power[1]
R [R+Rcjoinedbyjumper]
O/B Changeovervalve[5]
Y Compressorrelay
G Fanrelay
C 24VACcommon[3]
S1 Optionaloutdoor/remotesensor
S2 Optionaloutdoor/remotesensor
2H/2C Heat Pump (no auxiliary heat)
Y2 Compressor2relay
Rc Power[1]
R [R+Rcjoinedbyjumper]
O/B Changeovervalve[5]
Y Compressor1relay
G Fanrelay
C 24VACcommon[3]
S1 Optionaloutdoor/remotesensor
S2 Optionaloutdoor/remotesensor
3H/2C Heat Pump (with auxiliary heat)
Y2 Compressor2relay
L Equipmentmonitor[6,7]
E Emergencyheatrelay[8]
Aux Auxiliaryheatrelay(Heat2)[8]
Rc Power[1]
R[R+Rcjoinedbyjumper]
O/B Changeovervalve[5]
Y Compressor1relay
G Fanrelay
C 24VACcommon[3]
S1 Optionaloutdoor/remotesensor
S2 Optionaloutdoor/remotesensor
Shadedareasbelowapplyonly to P340-1320.
Wiring guide—heat pump systems
Wiring
See[notes]below
 [1] Powersupply.Providedisconnectmeansandoverloadprotectionasrequired.
 [3] Optional24VACcommonconnection.
 [5] O/B set to control as either Oor Bininstallersetup.
 [6] IfLterminalisused,24VACcommon(terminalC)must be connected.
 [7] Heatpumpreset(poweredcontinuouslywhenthermostatissettoEm.Heat;systemmonitor
whensettoHeat,Cool,orOff).
 [8] InstallfieldjumperbetweenAux and Eterminalsifthereisnoemergencyheatrelay.

Installation Guide
69-2268—03 6 570-219
M29126
M29125
M29129
Remove tab.
Alignpinsonbackofthermostatwith
slotsinwallplate,thenpushgently
untilthermostatsnapsintoplace.
Remove tab and mount thermostat
Set date and time
Press st
to set time
Press st
tosetyear
Press st
to set date
Press st
to set month
Installer setup
Press DONE to save changes. Press DONE to save and exit.
1. Press SYSTEM.2. Press and hold
thesetwobuttons
untilthedisplay
changes.
3. Changesettings
asrequired(see
pages7-9).

P340 Series
570-219 7 69-2268—03
M28652
Installer setup
Setting
Press DONE to
exit & save settings.
Press st to
change setting
Shadedareasbelowapplyonly to P340-1320
0120 Year
(rst two digits)
20(2000-2078)
21 (2101-2178)
0130 Year
(second two digits)
06 (2006)
 [Otheroptions:01-99]
0140 Month 6 [Otheroptions:1-12]
0150 Date 15 [Otheroptions:1-31]
0160 Schedule format 4 7-day programming
0 Non-programmable
0170 System type 1 1 heat/1 cool conventional
2 1heat/1coolheatpump(noaux.heat)
3 Heatonly(2-wiresystems)
4 Heatonlywithfan
5 HotwaterSeries20system(powertoopen&closezone
valves/normallyopenzonevalves)
6 Coolonly
7 2heat/1coolheatpump(withaux.heat)
8 2heat/2coolmultistageconventional
9 2heat/1coolmultistageconventional
10 1heat/2coolmultistageconventional
11 2heat/2coolheatpump(noaux.heat)
12 3heat/2coolheatpump(withaux.heat)
0180 Fan control
(heating)
0 Gas/Oil heat (equipment controls heating fan)
1 Electricfurnace(thermostatcontrolsheatingfan)
0190 Changeover valve
(O/B terminal)
0 O/B terminal controls valve in cooling
1 O/Bterminalcontrolsvalveinheating
0200 Auxiliary heat 0 Electric backup heat
1 Fossilfuelbackupheat
0210 External fossil
fuel kit
1 External fossil fuel kit controls backup heat
0 Thermostatcontrolsbackupheat(outdoorsensorrequired)
0220 1st stage com-
pressor cycle rate
3 Recommended for most compressors
 [Otheroptions:1,2,4,5or6CPH]
0230 2nd stage com-
pressor cycle rate
3 Recommended for most compressors
 [Otheroptions:1,2,4,5or6CPH]
Continuedonnextpage
Setup functions Settings & Options (factorydefaultinbold)
Function
Press st to
selectfunction

Installation Guide
69-2268—03 8 570-219
Shadedareasbelowapplyonly to P340-1320.
0240 First stage heat
cycle rate (CPH=
cycles per hour)
5 Gas or oil furnaces of less than 90% efciency
1 Steamorgravitysystems
3 Hotwatersystems&furnacesof90%+efciency
9 Electricfurnaces
 [Otheroptions:2,4,6,7,8,10,11,12CPH]
0250 Second stage heat
cycle rate (CPH)
5 Gas or oil furnaces of less than 90% efciency
1Steamorgravitysystems
3Hotwatersystems&furnacesof90%+efciency
9Electricfurnaces
[Otheroptions:2,4,6,7,8,10,11,12CPH]
0260 Third stage heat
cycle rate (CPH)
9 Electric auxiliary heat or electric furnaces
1Steamorgravitysystems
3Hotwatersystems&furnacesof90%+efciency
5Gasoroilfurnacesoflessthan90%efciency
[Otheroptions:2,4,6,7,8,10,11,12CPH]
0270 Emergency heat
cycle rate (CPH)
9 Electric emergency heat
1Steamorgravitysystems
3Hotwatersystems&furnacesof90%+efciency
5Gasoroilfurnacesoflessthan90%efciency
[Otheroptions:2,4,6,7,8,10,11,12CPH]
0280 Backlight 0 Backlight on for approx. 8 seconds after keypress
1Backlightalwaysonlowintensity,fullbrightafterkey-
press(requires24VACconnection)
0300 Manual/Auto
changeover
0 Manual changeover (Heat/Cool/Off)
1Automaticchangeover(Heat/Cool/Auto/Off)
0310 Auto changeover
deadband
3 Heat/cool temperature 3°F apart (1.5°C) **Seepage11
[Otheroptions:2-9(2°Fto9°F/1°Cto5°C)]
0320 Temperature
display
0 Fahrenheit
1Celsius
0330 Daylight savings 2 Auto-change to daylight savings time(2007andbe-
yond,forareasthatusethenew2007DSTcalendar)
1 Auto-changetodaylightsavingstime(through2006,and
forareasthatdo notusethenew2007DSTcalendar)
0Daylightsavingstimeisturnedoff
0340 Remote sensor 0 No remote sensor
1Outdoorsensor(displayonly)
2Outdoorcontrolsensor(selectheatpumps)**Seepage11
3Indoor sensor
0350 Heat pump
compressor lockout
0 No heat pump compressor lockout ** Seepage11
[Otheroptions:15,20,25,30,35,40,45°F(-9.5°Cto7°C)]
0360 Heat pump
auxiliary lockout
0 No heat pump auxiliary lockout ** Seepage11
[Otheroptions:40,45,50,55,60°F(4.5°Cto15.5°C)]
Installer setup
Continuedonnextpage
Setup functions Settings & Options (factorydefaultinbold)

P340 Series
570-219 9 69-2268—03
0500 Furnace lter
change reminder
0 Off
1 10-dayruntime(about1month)
2 30-dayruntime(about3months)
3 60-dayruntime(about6months)
4 90-dayruntime(about9months)
5 120-dayruntime(about1year)
6 365-dayruntime(about3years)
0510 Humidier pad
change reminder
0 Off
1 90calendardays
2 180calendardays
3 365calendardays
0520 UV lamp change
reminder
0 Off
1 365calendardays
0530 Early Recovery 1 On **Seepage11
0 Off
0540 Program periods 4 4 program periods (Wake, Leave, Return, Sleep)
2 2programperiods(Wake,Sleep)
0580 Compressor
protection
5 5 minute compressor off time **Seepage11
 [Otheroptions:0,2,3or4-minuteofftime]
0600 Heat temperature
range stop
90 Max. heat temperature setting is 90°F (32°C)
 [Otheroptions:40-89°F(4.5°Cto31.5°C)]
0610 Cool temperature
range stop
50 Min. cool temperature setting is 50°F (10°C)
 [Otheroptions:51-99°F(11°Cto37°C)]
0640 Clock format 12 12-hour time (i.e., “3:30 pm”)
24 24-hourtime(i.e.,“15:30”)
0650 Extended fan
timer (heat)
0 Off
90 Fanrunsfor90secondsaftercallforheatends
0660 Extended fan
timer (cool)
0 Off
90 Fanrunsfor90secondsaftercallforcoolingends
0670 Keypad lock 0 Keypad unlocked (fully functional)
1 Partiallylocked(accesstotemperaturesettingsonly)
2 Fullylocked
0680 Heat temperature
control
2 Standard temperature control (recommended)
1 Chooseifroomiswarmerthansettemperature
3 Chooseifroomdoesnotreachsettemperature
0690 Cool temperature
control
2 Standard temperature control (recommended)
1 Chooseifroomiscoolerthansettemperature
3 Chooseifroomdoesnotreachsettemperature
0700 Temperature
display offset
0 Thermostatdisplaysactualroomtemperature
 [Otheroptions:-3,-2,-1,1,2,3°Foffset(-1.5°Cto1.5°C)
0710 RESET 0 No reset
1 Resetinstalleroptions&programscheduletofactory
default(onlydateandtimesettingsareretained)
Installer setup
Setup functions Settings & Options (factorydefaultinbold)

Installation Guide
69-2268—03 10 570-219
M29127
Duringinstallersetup,presst
repeatedlyuntil“Test”appears.
Test
number
System
status
Press st to
select test
Press st to
change status
Press DONE to terminate testing.
Shadedareasbelowapplyonly to P340-1320.
1 Cooling system 0 Compressorandfanturnoff
1 Compressorandfanturnon
2 Secondstagecompressorturnson
2 Fan system 0 Fanturnsoff
1 Fanturnson
3 Heating system 0 Heatandfanturnoff
1 Heatturnson(fanonifFunction0170issetforheatpump,
orifFunction0180issetto“1”)**Seepage6
2 Second stage heat turns on
3 Third stage heat turns on
4 Emergency
heating system
0 Heatandfanturnoff
1 Heatandfanturnon
2 Secondstageheatturnson(Auxiliaryheat)]
System test System status
CAUTION: EQUIPMENT DAMAGE HAZARD. Compressorprotectionisbypassed
duringtesting.Topreventequipmentdamage,avoidcyclingthecompressorquickly.
Installer system test

P340 Series
570-219 11 69-2268—03
Auto Changeover(SetupFunction0300):WhensettoAuto,thethermostatautomaticallyselectsheatingorcooling
dependingontheindoortemperature.Heatandcoolsettingsmustbeatleast2degreesapart.
Remote Sensor(SetupFunction0340):Ifanoptionaloutdoorsensorisinstalled,thethermostat
candisplaytheoutsidetemperature.Ifanoptionalremoteindoorsensorisinstalled,thethermo-
statwilldisplaythetemperatureatthesensorlocation(theinternalsensorinthethermostatisnot
used).
Early Recovery(SetupFunction0530):Allowsthethermostatto“learn”howlongthefurnaceand
airconditionertaketoreachprogrammedtemperaturesettings,sothetemperatureisreachedat
the scheduled time.
Compressor Protection(SetupFunction0580):Forcesthecompressortowaitafewminutes
beforerestarting,topreventdamage.Duringthistime,themessage“Wait”ashesonthedisplay.
Heat Pump Compressor Lockout(withfossil-fuelbackup):Ifthethermostatisinstalledwithanoptionaloutdoor
sensor,youcanselectacompressorlockouttemperature(Function0350).Whentheoutdoortemperatureisbelowthe
lockouttemperature,onlytheauxiliaryheatoperates.Whentheoutdoortemperatureisabovethelockouttemperature,
onlythecompressoroperates.
Heat Pump Auxiliary Lockouts(withelectric heatbackup):Ifthethermostatisinstalledwithanoptionaloutdoor
sensor,youcanselectacompressorlockouttemperature(Function0350)and/oranauxiliaryheatlockouttemperature
(Function0360).Whentheoutdoortemperatureisbelowthecompressorlockouttemperature,onlytheauxiliaryheat
operates.Whentheoutdoortemperatureisabovetheauxiliarylockouttemperature,onlythecompressoroperates.
Iftheoutdoortemperatureisbetweenthecompressorandauxiliarylockouttemperatures,boththecompressorand
auxiliaryheatcanoperate.
Shadedareasbelowapplyonly to P340-1320.
Special functions
Pleasecontactyourdistributortoorderreplacementparts.
Outdoor temperature sensor...............................................Part Number P350-OSEN-R340
Remote indoor temperature sensor...................................Part Number P350-ISEN-R340
Cover plate Assembly*.........................................................PartNumberP350-CP-MULTI
*(Usetocovermarksleftbyoldthermostats.)
Accessories & replacement parts

Installation Guide
® U.S. Registered Trademark.
© 2009
69-2268—03M.S.05-09
Temperature Ranges
• Heat:40°to90°F(4.5°to32°C)
• Cool:50°to99°F(10°to37°C)
Operating Ambient Temperature
• 0°to120°F(-18°to48.9°C)
Shipping Temperature
• -30°to150°F(-34°to66°C)
Operating Relative Humidity
• 5%to90%(non-condensing)
Physical Dimensions
• 4-9/16”Hx6”Wx1-3/8”D
• 116mmHx152mmWx35mmD
Electrical Ratings
Terminal Voltage(50/60Hz) RunningCurrent
WHeating 20-30Vac 0.02-1.0A
(Powerpile) 750mVDC 100mADC
W2Heating 20-30Vac 0.02-0.6A
YCooling 20-30Vac 0.02-1.0A
Y2Cooling 20-30Vac 0.02-0.6A
AuxAuxiliaryheat 20-30Vac 0.02-1.0A
O/BChangeover 20-30Vac 0.02-0.6A
EEmergencyheat 20-30Vac 0.02-1.0A
LHeatpumpreset 20-30Vac 0.02-0.6A
Specifications