Toto TLE03502U1i2 User manual

STEP 1
1. Pull the battery tab out from
daughter card enclosure.
NOTE:
Red LED light will blink to indicate
that the device is functioning.
Controller Mounting Accesories Faucet Manual
0GU3076
Manual
(Refers to this document)
1-5/8” (40mm)
EcoPower Faucet Controller
Daughter Card Installation Manual
0GU3092 Rev. A
Daughter Card Connection (white)
Daughter card
enclosure NOTE:
“CLICK” sound.
WARNING:
HANDLE WITH CARE.
COMPONENTS MAY STAY LOOSE
AFTER INSTALL. THIS IS NORMAL.
DO NOT DROP.
- TLE03502U1i2
- TLE03502U3i2
- TLE03501U2i2
- TLE03503U1i2
Daughter Card
STEP 2
Connect Controller and
Daughter Card:
Connect the wire harness
connection.
Listen for the “click”
indicating a secure
connection.
STEP 3
Assemble the cover and controller body.
Slide the hook of the enclosure
sideways into the side opening
of the controller cover unit.
STEP 5
Test Run:
Follow the instructions in the original faucet
installation manual.
STEP 6
Commit daughter card:
Follow GP’s instructions.
Please contact TOTO at 888-295-8134, or Georgia-Pacic at 800-890-0896
or [email protected] for any questions regarding installation or
maintenance.
STEP 4
Fasten the cover to the controller body:
Replace controller cover and carefully
guide the screw into the controller
assembly.
SLIDES
INTO
NOTE:
Make sure wire
harness is secured.
Do not pinch.
Do not kink.
NOTE:
Make sure wire harness stays secured.
Do not pinch. Do not kink.
NOTE: Install the controller and spout rst. Proceed with the instructions below after completing the installation procedures on Page#12 of the Installation and Owners Manual 0GU3076.
TOP
NOTE:
Correct orientation.
Please read and adhere to these notes. Failure to do so could result in
personal injury, risk of re or smoke and/or property damage.
- Install the product according to installation instructions.
- Install the product in the correct vertical orientation.
- Do not use or operate the product with it’s covers removed.
KEEP THIS DOCUMENT FOR REFERENCE AND MAKE AVAILABLE FOR MAINTENANCE PERSONNEL.
LED Light
Battery Tab
The IoT daughter card installation requires
minimum 13/16” (20mm) clearance on the
left side of the controller. Please refer to
the diagram, as shown.
The daughter card extends 1-5/8” (40mm)
below the controller. Make sure the
bottom of the daughter card doesn't hit
any obstacles.
INCLUDED PARTS
WARNINGS
INSTALLATION PROCEDURE
BEFORE INSTALLATION
Min 13/16”
(20mm)

EcoPower Faucet Controller
Daughter Card Installation Manual
FCC:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
Changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
FCC Interference Statement Part 15.105 (b)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To comply with FCC and Industry Canada RF exposure limits for general population / uncontrolled exposure, the antenna(s) used for this
transmitter must be installed to provide a separation distance of at least 43mm from all persons and must not be operating in conjunction with
any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures..
Industry Canada:
This Device complies with Industry Canada License-exempt RSS standard(s). Operation is subject to the following two conditions: 1) this device
may not cause interference, and 2) this device must accept any interference, including interference that may cause undesired operation of the
device.
Cet appareil est conforme avec Industrie Canada, exempts de licence standard RSS (s). Son fonctionnement est soumis aux deux conditions
suivantes: 1) ce dispositif ne peut pas causer d'interferences. et 2) ce dispositif doit accepter toute interference, y compris les interferences qui
peuvent causer un mauvais fonctionnement de ('appareil.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved
for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen
that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
Daughter Card
Enclosure
AA batteries
X 4
Replacing the batteries:
1- Loosen screw and remove controller cover.
2- Disconnect daughter card connection wire.
3- Open the daughter card enclosure by loosening captive screw.
4- Remove the four (4) AA batteries and replace with four (4) new AA alkaline batteries.
5- Carefully close the daughter card enclosure. Tighten captive screw. Do not overtighten.
6- Reattach as per installation instructions on reverse.
- TLE03502U1i2
- TLE03502U3i2
- TLE03501U2i2
- TLE03503U1i2
Follow these instructions carefully. Failure to do so could result in personal injury, risk of re, smoke and/or property damage.
- Handle the product with care when performing maintenance.
- DO NOT pull, twist or damage the wires or connectors. Risk of product malfunction.
- NEVER splash water on the components. This is an electrical device. DO NOT get the components wet. Risk of product malfunction.
- Install the product in the correct vertical orientation
Follow these instructions carefully. Failure to do so could cause incorrect data reporting.
- Each daughter card has been electronically paired to a specic controller. DO NOT MIX UNPAIRED SIMILAR
COMPONENTS EVEN IF THEY APPEAR TO BE IDENTICAL.
- When providing maintenance, please keep track of paired components.
- Make sure paired daughter card reconnects to it’s exact corresponding paired controller.
- Failure to reconnect corresponding paired components will result in product malfunction.
MAINTENANCE WARNINGS
MAINTENANCE INSTRUCTIONS
REGULATORY STATEMENTS