Touchboards InVision 37108 User manual

0112774 Page 1 of 4
Assembly Instructions
Assembly Instructions
Before you begin, please make sure all parts and proper quanti-
ties are included. Any parts damaged during shipment must be
reported within 15 days of receipt. To report information regarding
damages or if you have any questions, please call 1-800-235-1262.
To purchase parts or accessories, please contact us at
www.spectrumfurniture.com
1-800-235-1262
Thank you for purchasing Spectrum products!
Camera Mount for InVision
Camera Mount for InVision
™
™
Media Collaboration Table
Media Collaboration Table
#37108
#37108
4mm hex wrench
(included)
7/16” or adjustable wrench
drill with 3/8” drill bit
Tools Required
Tools Required
(1) 025039
4mm hex wrench
(1) 0112503
12”W x 8-1/2”D shelf
The Invision camera mount comes with two different shelf sizes to ac-
commodate multiple camera and video devices. The mount can also be
located in two different positions: above the monitor for group teleconfer-
encing, or below the monitor for face-to-face conferencing.
(4) 059534
1/4-20 x 30mm
JC bolt
(6) 041943
1/4-20 locknut
(1) 0112502
6-1/2”W x 8-1/2”D shelf
(1) 0112504
shelf bracket
Figure 1
A. Choose one shelf (large or small) that fits your specific camera.
B. Attach the bracket to the shelf as shown with (2) 1/4-20 locknuts
and tighten securely. Figure 1.
1. Camera mount assembly
1. Camera mount assembly
large or small
shelf
1/4-20 locknut
(2 req’d)
shelf bracket
(4) 026059
1/4 flat washer

0112774 Page 2 of 4
A. Using two people, carefully lift the monitor off the monitor mount and set aside.
B. Remove the display stand back panel by removing the (6) 1/4-20 x 30mm JC bolts (retain these bolts) and set aside. Figure 2.
C. Locate the two 3/8” holes in the display stand front panel. These holes do not go all the way through the panel so they will need to be drilled out.
Figure 3.
D. Using a drill with a sharp 3/8” drill bit, slowly drill through the display stand panel at the two 3/8” hole locations. Figure 3.
E. Orient the assembled camera mount as shown with the display stand front panel. Using the center slot, align the shelf bracket with the two
centered mounting holes and install (2) 1/4-20 x 30mm JC bolts with (2) 1/4-20 locknuts (not shown) and (2) 1/4 washers (not shown) on the back.
Figure 4.
F. Carefully lift the monitor back onto the monitor mount.
G. Adjust the camera mount to sit below the installed monitor with enough clearance for your camera, then tighten the bolts securely. Figure 5.
H. Install camera onto the shelf.
I. Route cords through the display stand front panel grommets.
J. After all electrical connections are made, re-attach the display stand back panel with the (6) 1/4-20 x 30mm JC bolts and tighten securely.
Installation below monitor
Installation below monitor
Figure 4
display stand
front panel
assembled
camera mount
(2) 1/4-20 x 30mm JC bolts
with (2) 1/4 washers and
(2) 1/4-20 locknuts on back
camera
mount
adjust shelf
below monitor
monitor
Figure 5
While the camera mount can be installed below the monitor with the monitor still installed, Spectrum recom-
mends the monitor be temporary lifted off the monitor mount to simplify installation and prevent monitor damage.
Figure 3
display stand
front panel
(2) 3/8” holes
in panel
drill w/
3/8” drill bit
1/4-20 x 30mm
JC bolt
display stand
back panel Figure 2
monitor
mount

0112774 Page 3 of 4
A. Using two people, carefully lift the monitor off the monitor mount and set aside.
B. Remove the display stand back panel by removing the (6) 1/4-20 x 30mm JC bolts (retain these bolts) and set
aside. Figure 6.
C. Remove the screws attaching the angled filler to the back panel. Figure 7.
D. Flip the angle around and re-attach to the panel with the cutout side facing up as shown. Figure 7.
Installation above monitor
Installation above monitor
Figure 7
angled filler flipped with
cutout side facing up
(for above-monitor
installation)
angled filler with
solid side facing up
(for below-monitor
installation)
display stand
back panel
remove
screws re-attach with
screws
display stand
back panel
Figure 8
E. Locate the four 3/8” holes on top of the display stand front panel.
These holes do not go all the way through the panel so they will need
to be drilled out. Figure 8.
F. Using a drill with a sharp 3/8” drill bit, slowly drill through the display
stand panel at the four 3/8” hole locations. Figure 8.
While the camera mount can be installed above the monitor with the monitor still installed, Spectrum recom-
mends the monitor be temporary lifted off the monitor mount to simplify installation and prevent monitor damage.
1/4-20 x 30mm
JC bolt
display stand
back panel Figure 6
monitor
mount
drill w/
3/8” drill bit
display stand
front panel
(4) 3/8” holes
in panel

0112774 Page 4 of 4
925 FirstAvenue, PO Box 400, Chippewa Falls, WI 54729 Ph: 1-800-235-1262 Fax: [phone]
E-mail: [email protected] web: www.spectrumfurniture.com
Figure 9
1/4-20 x 30mm JC bolts
(4 req’d)
assembled
camera mount
1/4 washers
(4 req’d)
G. Orient the assembled camera mount as shown in Figure 9.
H. Using the outer slots, attach the camera mount to the back side
of the display stand front panel with (4) 1/4-20 x 30mm JC bolts,
(4) 1/4 washers, and (4) 1/4-20 locknuts. Do not tighten fasteners
completely yet.
I. Carefully lift the monitor back onto the monitor mount.
display stand
front panel
monitor mount
Figure 10
adjust shelf just
above monitor
J. Adjust the camera mount to sit just above the installed monitor then
tighten the shelf fasteners securely. Figure 10.
K. Install your camera on the shelf and route cords down behind the
monitor and through the display stand front panel grommets.
L. After all electrical connections are made, re-attach the display stand
back panel with the (6) previously removed 1/4-20 x 30mm JC bolts
and tighten securely. Figure 11.
1/4-20 x 30mm
JC bolt
display stand
back panel
camera mount
Figure 11
monitor
camera
mount
1/4-20 locknuts
(4 req’d)