Towerpro Mag 8 User manual

Towerpro Mag 8 Brushless
Speed Controller Manual
Motor
O pe ration L imit:
12.A: max current 15A , continuous cur rent 12.A for J0 minu tes
25A: max current 30A, continu ou s cur rent 25A for J0 minute s
3
0A : max current 35 A, co nt inu ou s cur rent 30A for J0 m inute s
Voltage Rang e: 6V-1 2V
Nu mber of Ba tte ries : 4-12Ni MH , 2- 3L iPo
B Ee Outp ut: 5V J.5A .2L iPo\4-5mini servo, 3Li p o\ 3 -4min i servo
Prot
ect i ve Functions:
•
Au tomat ically select 2-3LiP o,protc ctivc v olta ges arc 6VI9V re spe ctively;
•
Au tomat ically select N iMH, the p rote ctive volt age for each battery is O.SY.
• S afe start - will not start if the t hro ttle stick is not in the right po sit ion;
• Temperature
pro tection, shu tdo wn if the su rf ace temp era ture reaches 110°C
• lost of control protection , sh utdown after I second without signal.
Perf
orm ance:
• motor limit:
* 2-po le advcr sio n as high as 3000 00 rpm
*12-p ole a dvc rsion 5 00 00r pm
*1 4-p ole a dvc rsion 42 000 rpm
• For 8
KHzp \VM control ,
• Positi on of the full,
thrott le will be ad ju st automati ca lly
• B Ee and MCU use separate power supply for table oper ation.
Sett
ing M ethod:
I . O pen the transmitter, switch throttle stick to the full po wer position (for FU TABA series
transmi tt er, the thro ttle stick sha ll be s wit ched to R EV ).
2. C onn ect the r ece i ve r and m ot or.
3. C
onn ect the power to t he speed controller.
4 . If the
tra n smit ter is in normal c ond ition, it will have the following sound: (if th er e are no more
s ounds after a long low sound at the end of this so und , check the re ve r se setti ng of the
transmi tt er t hro ttle channel ).
*B: indi cat es UPO au toma tic p rote ction
*BB BB : indicates NiMH /Ni CD aut omati c prote ction
* BBB BBB : ind icates brak e selection
5.
If th ere is setting you wa nt in the p roce ss of s ound cycl e, switch the t hro ttle
stick, to the lowest po sition at the first time interval. (For example, select
LlPO au toma tic pro te ctio n: switch the thrott le stick to the lo west po sition when
h
ear ing one B sound)
6.
If the re is an other additional s ettin g, quickly switch the gun to the highest po sit ion to make a
sele
ction .

7. If you hav e finis hed the setti ng you require, wait 2 s econd s and the moto r will s end a
confirmation sound for battery
pro tect ion. It is u sab le after confirming the posi tio n of throttle
stick.
8.
LIFO automa tic p rot ect ion ha s only 2 volta ge prote ction points , i.c 6V and 9V The re is no
n
eed to use a full c apa city b atte ry.
9. NiMH automatic
prote ction is calc ulat ed accor din g to the real number of ba tte ries. Se ts
O.SV for each b atte ry. In order to ensure ac cu rate j udgment of t he battery vol ta ge, ple a se
charge the ba ttery to full capa cit y. If the battery is not at full ca pac ity. The speed cont roller
will estimate the pro
te ction voltage according to 53% of the full capa cit y.
10. the
br a ke is se ein g as d ef ault set
1J. Reset the
br ake op era tion to rel eas e the brake fun ctio n. .
12.
Fa cto ry par am eter reset function: because this series of elec tro nic gove rnor ha s an
overheating and false operation
prote ctive func tio n, if you find that the speed c ont roller is
acce ler ating or changing is direction , or t he thro ttle is diff eren t from t he orig inal cond ition,
you can
reset the factory parameters to obtain the highe st pe rformance.
When starting the m ach ine there is a long B s oun d. It indicates that the elec tro nic govern or is
in LIFO protection mod e. Th e BBB sound indicates t hat it is in NiM HlN iCD a utoma tic
p rot ection m ode .