TownSteel ED3727 User manual

INSTALLATION INSTRUCTIONS FOR HEAVY DUTY
NARROW STILE SURFACE VERTICAL ROD EXIT DEVICE
Lift Arm
OUT
RIGHT HAND
REVERSE BEVEL
LEFT HAND
REVERSE BEVEL
Plastic Guide
Surface of Door For
Exit Device Applied Must Be
Flushed.
A. THE DOOR MUST BE HANGING CORRECTLY.
B. SIZE OF EXIT DEVICE, FUNCTION AND DESIGN....
B.1. 36" DOORS, CAN BE CUT TO FIT DOORS DOWN TO 30" WIDE.
B.2. 48" DOORS, CAN BE CUT TO FIT DOORS DOWN TO 36" WIDE.
B.3. HANDING OF DEVICE.
BEFORE INSTALLING DEVICE, PLEASE CHECK:
(Only available
on fire rated)
(Only available
on fire rated)
TO CHANGE HANDING OF DEVICE
( FOR EXAMPLE: FROM LHR to RHR )
PRESS LIFT ARM "C" AND ENSURE THE DIRECTION.
The screw "A" is at the below hole position as figure shown UNSCREW "A" AND TAKE OFF "B".
TURN "B" 180° AND PUT IT BACK AS FIGURE SHOWN
THEN, FASTEN "A" AT ABOVE SCREW HOLE.
OPERATE LIFT ARM "C" TO ENSURE THE
PROCESSING DIRECTION IS REVERSED.
C. TO CHANGE HANDING OF DEVICE. (SEE FIG AT BELOW)
C.1. USE PIN, 2- 14" LONG, TO KNOCK OUT LIFT LEVER PIN.
C.2. REMOVE LIFT LEVER AND REASSEMBLE OTHER END.
( LHR )
( RHR )
PARTS LIST
DESCRIPTION
ITEM QTY
CHASSIS ASSY1 1
1PUSH BAR
21
MOUNTING RAIL3 1
HEAD COVER41
SLIDING COVER51
BRACKET6 1
END CAP7 1
TOP ROD10 1
TOP LATCH
11 1
TOP STRIKE12 1
BOTTOM ROD
13
1
BOTTOM STRIKE15 1
SM4*8 FLAT HEAD SCREWS
A10
C 2
D4
10#*1-1/4" FLAT HEAD TEK SCREWS
E8 SEX BOLT
B8
LATCH COVER8 2
ROD GUIDE9 2
1
BOTTOM LATCH
14
10#*3/4" FLAT HEAD SCREWS
10#*5/8" ROUND HEAD SCREWS
F10#*1-1/4" ROUND HEAD TEK SCREWS 12
1
2
3
4
5
ALLEN WRENCH5-1 1
5-1
(NOT FOR FIRE RATED)
7
6
8
8
10 9
11
12
C
D
FB
Plastic Guide
13
15
B
C
F
D
14
A
A
B
E
F
B
F
B
E
E
E
E
E
(Only available
on fire rated)
9
F
(Only available
on fire rated) E
F
E
B
A
E
(Only available
on fire rated)
B
B
(Only available
on fire rated)
" "
" "
" "
" "
" "
" "
" "
" "
" "
" "
(Not available
on fire rated)
2020-B

4. ATTACH TOP AND BOTTOM CHASSIS
A. MOUNT TOP STRIKE PER LOCATION
IN 2ND STEP.
B. SCREW TOP ROD INTO MAIN SLIDE.
C. SLIDE GUIDE AND COVER ON TO TOP
ROD CHASSIS BY INSERTING ADJ PIN.
THRU RETRACTOR AND MIDDLE HOLE
IN ROD. (SEE FIG AT RIGHT)
ADJ TOP CHASSIS MOUNTING HOLES LINE
UP WITH LOCATION MARKED IN 2ND. STEP.
D. MOUNT BOTTOM CHASSIS SAME WAY AS TOP
CHASSIS (SEE FIG AT RIGHT)
E. AS TO BOTTOM STRIKE APPLICATION VARIATIONS.
PLEASE REFER FIG BELOW FOR THE CORRECT
MARRIAGE.
F. FASTEN GUIDE.
IF SHORTER ROD REQUIRED, CUT TO
LENGTH AND DRILL 1/8"∅HOLE THRU.
CHECK THE DEVICE IS OPERATING NORMALLY,
AND FASTEN COVERS WITH SCREWS AS BELOW.
TOP LACTH COVER
BOTTOM LACTH COVER
TOP
DOOR STRIKE
THRESHOLD SURFACE
STRIKE MORTISE STRIKE
5. APPLY RAIL ASSEMBLE
A. CHECK THE SIZE OF DEVICE, IF CUTTING IS REQUIRED.
B. DETERTMINE CUT OFF LENGTH "X" BY SUBTRACTING 1-3/4"
FROM "Y". MARK CUT OFF POINT ON MOUNTING RAIL.
ATTACH MOUNTING PLATE TO
DOOR WITH (2) FLAT HEAD TEK
SCREWS OR SEX BOLT .
C. DREPRESS ARM INTO RAIL OPENING AND SLIDE RAIL ONTO
CHASSIS. LEVEL RAIL AND FASSTEN CHASSIS AND MOUNTING PLATE.
LEVEL
RAIL Assy MOUNTING PLATE SCREWS
VERTICAL
CHASSIS
FOR DOOR W/STILE CUT OFF
MUST LEAVE 1/2" MIN
OVERLAP WITH RAIL
1-3/4" MIN.
X
Y
CUT OFF AND DEBURR
DON'T CUT CLOSER THAN 5-3/8"
FROM PUSH BAR END CAP
6. APPLY COVERS
ATTACH COVER TO CHASSIS
WITH (4) M4X8 TRUSS HEAD
MACHINE SCREW.
ATTACH END CAP TO MOUNTING
PLATE WITH (2) M4X8 COVER SCREWS.
<WITH (2) M4X8 Screw>
<WITH (2) M4X8 Screw>
Top Latch Assy
Latch Cover
Rod Guide
Top Rod
Bottom Latch Assy
Bottom Rod
Lift Arm
Rod Guide
Latch Cover
Plastic Guide
Plastic Guide
FINISHED FLOOR
VERTICAL CHASSIS
TOP AND BOTTOM CHASSIS
C
L
HORIZONTAL CHASSIS
41" OR VARIABLE FROM
FINISHED FLOOR
C
L
BACKSET
1. MARK VERTICAL AND HORIZONTAL
REFERENCE LINES ON DOOR.
DETERMINE BACKSET TO LOCATE VERICAL REFERENCE LINE.
A. IF LOCK STILE IS 4-1/2" WIDE OR WIDER BACKSET IS 1-15/16".
B. IF LOCK STILE IS LESS THAN 4-1/2" WIDE, BACKSET
IS HALF OF THE EXPOSED WIDTH OF LOCK STILE.
2. DOOR PREPARATION
TAPE TEMPLATE ON INSIDE OF
DOOR ALONG REFERENCE LINE.
SPOT AND DRILL HOLE.
STOP THICKNESS
DOOR STOP
TOP CHASSIS TEMPLATE
TAPE
HORZIONTAL REFERENCE
LINE
VERITICAL REFERENCE LINE
CYLINDER
CYL RING
LINER INSTALLTION
SCREW
(#10-24*1")
5/8" 7/8"
~
TAILPIECE PROJECTION
3. INSTALL CYLINDER
A. INSERT THE CYLINDER THROUGH CYL RING HOLE ON
THE DOOR.
B. KEEP THE TAILPIECE HORIZONTALLY.
C. MOUNT LINER ON INSIDE OF DOOR .
D. TAILPIECE PROJECTION OVER INSIDE OF DOOR IS SUGGESTED
IN THE RANGE "5/8 7/8 ". IF NECESSARY, USE A PLIER TO
BEND AND CUT TO DESIRED LENGTH.
~
FLAT HEAD
TEK SCREWS
SEX BOLT
(ROUND HEAD SCREWS)
(Only available
on fire rated)
2020-B