TP-Link TD-8811 User manual

COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. is a registered
trademark of TP-LINK Technologies Co., Ltd. Other brands and product names are
trademarks or registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means or used to
make any derivative such as translation, transformation, or adaptation without permission
from TP-LINK Technologies Co., Ltd. Copyright © 2006 TP-LINK Technologies Co., Ltd.
All rights reserved.
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
EC DECLARATION OF CONFORMITY (EUROPE)
In compliance with the EMC Directive 89/336/EEC, Low Voltage Directive 73/23/EEC, this
product meets the requirements of the following standards:
• EN55022
• EN55024
• EN60950
SAFETY NOTICES
Caution: Do not use this product near water, for example, in a wet basement or near a
swimming pool.
Avoid using this product during an electrical storm. There may be a remote risk
of electric shock from lightning.

Package contents.............................................................................................................. 2
Chapter 1: Product Overview............................................................................................ 3
1.1 Product main specification................................................................................... 3
1.2 Supporting protocol.............................................................................................. 3
1.3 Transmit data-rate................................................................................................ 4
1.4 ATM property........................................................................................................ 4
1.5 System support.................................................................................................... 4
1.6 Working environment........................................................................................... 4
1.7 Electric parameter................................................................................................ 4
Chapter 2: Hardware Installation Guide............................................................................ 5
2.1 System requirement............................................................................................. 5
2.2 LED explanation................................................................................................... 5
2.3 Rear-panel........................................................................................................... 5
2.4 Hardware installation procedures（figure2-1）................................................... 6
Chapter 3: System Configuration...................................................................................... 7
3.1 Computer Configuration....................................................................................... 7
3.2 Login.................................................................................................................... 8
3.3 Web Setup......................................................................................................... 10
3.4 Software Dial...................................................................................................... 19
3.5 USB Configuration............................................................................................. 20
Chapter 4: Advantage management setup...................................................................... 23
Chapter 5: FQA............................................................................................................... 24
Appendix A: Default Configuration .................................................................................. 25
Appendix B: Contact Information..................................................................................... 26

TD-8811 External ADSL2+ Router User Guide
Package contents
The following contents should be found in your box:
¾One TD-8811 External ADSL2+ ROUTER
¾One AC power Adapter for TD-8811 ExternalADSL2+ ROUTER
¾One Resource CD for TD-8811 External ADSL2+ ROUTER, including:
•This Guide
•Quick installation Guide Program
•Other Helpful Information
•USB driver
¾Quick installation Guide
¾One RJ45 cable
¾Two RJ11 cable
¾One ADSL splitter
¾One USB cable
Note: If any of the above items are damaged or missing, please contact the retailer from
whom you purchased the TD-8811 External ADSL2+ ROUTER for assistance.
- 2 -

TD-8811 External ADSL2+ Router User Guide
Chapter 1: Product Overview
TP-LINK® TD-8811 External ADSL ROUTER is the latest product designed and
manufactured by TP-LINK Technologies Co., Ltd. With TP-LINK’s excellent circuit design
and high quality production, we guarantee the ADSLROUTER’s high performance, great
stability and easy to use.
TD-8811 uses integrated ADSL2+ transceiver and a 256-MHz MIPS32 CPU, the AFE
supports full-rate ADSL connectivity conforming to the ITU and ANSI specifications;
MIPS32 CPU with MMU and 16-KB I-cache/8-KB D-cache is integrated into the device.
In addition to the basic DMT physical layer functions, the ADSL PHY supports dual latency
ADSL framing (fast and interleaved) and the I.432 ATM Physical Layer.
The TD-8811 is a complete plug-and-play solution. With standard Ethernet interface, it
can be directly connected to any 10M/100M Ethernet devices, support Auto-MDIX.
The TD-8811 not only uses html (web mode through Ethernet port) to configure the
ROUTER but also uses external utility software，too. You can download it from our
website (http://www.tp-link.com).
1.1 Product main specification
¾Adopts the high performance IC which integrates the AFE transceiver and the 256
MHZ MIPS32 CPU, guaranteeing that this product is efficient and steady.
¾High speed and asymmetrical data transmit mode, provides safe and exclusive
bandwidth
¾Supports All ADSL industrial standards
¾Compatible with all mainstream DSLAM (CO)
¾Firmware upgradeable
¾Provides integrated access of internet and route function which face to SOHO user
¾Advanced DMT modulation and demodulation
¾Real-time Configuration and device monitoring
¾Quick response semi-conductive surge protection circuit, provides reliable ESD and
surge-protect function
1.2 Supporting protocol
- G.992.1 (G.dmt) - Annex A/B/C
- G.992.2 (G.lite) - Annex A/B/C
- ANSI T1.413
- G.992.3 (ADSL2) - Annex A/B/C/M and Annex L (RE-DSL) compliant
- G.992.5 (ADSL2+) Annex A/B/C and Annex L (RE-DSL) compliant
- ADSL dual latency (fast path and interleaved path)
- I.432 ATM physical layer compliant
-Supports RFC2364 (PPPoA)
- 3 -

TD-8811 External ADSL2+ Router User Guide
-Supports RFC2516 (PPPoE)
-Supports RFC1483 (EoA)(Bridged *and route)
-Supports RFC1577 (IPoA)
NOTE. “*” Needs the third-party software.
1.3 Transmit data-rate
¾Max download data-rate: 24Mbps
¾Max upload data-rate: 1Mbps
¾Max line length: 6Km
1.4 ATM property
¾AAL0, AAL5, OAM, RM, and raw cell types supported
¾Direct hardware support for 4 Receive VCs, with additional RX VCs and TX VCs
supported in software
¾Full 24-bit Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI)
1.5 System support
¾Support PVC
¾Support NAT、DHCP and so on
¾Support IEEE 802.3、IEEE 802.3u
¾Support 10Base-T/100BASE-TX full-duplex or half duplex Ethernet
¾Support Auto-MDIX
¾Support USB 1.1 device interface
1.6 Working environment
¾Operating temperature: 0 ~40℃℃
¾Storage temperature: -40 ~70℃℃
¾Humidity: 10%~90% (non-condensing)
1.7 Electric parameter
¾Adaptor power Output: 9VAC/0.8A，50Hz or 60 Hz
¾Power consumption: 4W Maximum
- 4 -

TD-8811 External ADSL2+ Router User Guide
Chapter 2: Hardware Installation Guide
The TD-8811 maintains three separate interfaces, one Ethernet ,one USB interface and
one ADSL interface. The Router should not be located where it will be exposed to
moisture or excessive heat. Place the Router in a location where it can be safely
connected to the various devices as well as to a power source.
2.1 System requirement
Confirm your computer has been installed with networking interface card (NIC) before
connecting ADSL2+ ROUTER to your computer, with the operating system supporting
the TCP/IP protocol.
2.2 LED explanation
The front panel of ADSL2+ ROUTER includes one power indicator (RED) and five
function indicators (GREEN), as explained in chart 1-1:
Indicator Description Status Function Details
PWR Power On
Off Power OK Power fail
ADSL ADSL status
Slow flash
Quick flash
On
Self-detecting when power up
Connecting to the telecom network
Connection to telecom network OK
ALARM Mistake On
Off
There is mistake when ADSL transmitting data or
receiving data
ADSL normal
ACT Data On
Off
There is data transmitting or receiving on WAN
port
No data transmitting or receiving on WAN port
USB
USB status On
Off
Flash
Connection to telecom network OK
Connect on USB port abnormal
Data transmitting or receiving
LAN Ethernet
On
Off
Flash
LAN port normal
Connection on LAN port abnormal
Data transmitting or receiving on LAN port
Chart 1-1
2.3 Rear-panel
¾ON/OFF: Turn on/off the ADSL2+ ROUTER’s power.
¾Power (9VAC/0.8A input): please do not use any unknown power adaptor,
- 5 -

TD-8811 External ADSL2+ Router User Guide
otherwise your ADSL2+ ROUTER may be damaged.
¾RESET(reset default): First press the reset button of ROUTER, then turn on the
ROUTER’s power for at least three seconds. It will resume the default
manufacturer’s setup.
¾LAN: Connect with your computer’s NIC.
¾USB: Connect with your computer’s USB interface
¾LINE(WAN): Connect to the MODEM Port of Splitter or Connecting the telephone
line.
2.4 Hardware installation procedures（figure2-1）
The procedure to install the Router can be described in general terms in the
following steps:
First Step: Connecting the MODEM port of Splitter with the LINE port of the TD-8811
ADSL2+ ROUTER by telephone line. While you need to use a telephone, please attach
telephone line into the phone of Splitter.
Second Step: Connect category 5 cable with RJ45 jacks toADSL2+ ROUTER’s LAN
port and your computer’s NIC. Or connect USB cable toADSL2+ ROUTER’s USB port
and your computer’s USB interface
Third Step: Plug one end of the AC Power Adapter into the Power jack on the Ethernet
ADSL2+ ROUTER and the other end to a standard electrical outlet.
Last Step: Check the line connection to see if everything is ready. Power up finally.
Figure2-1
- 6 -

TD-8811 External ADSL2+ Router User Guide
Chapter 3: System Configuration
3.1 Computer Configuration
1. Connect the cable according to Chapter 2, turn on the power.
2. Change the IP address of your PC（Figure 3-1）: Open TCP/IP Properties of the LAN
card in your PC, enter the IP address as 192.168.1.* (* is any value between 2 to
254, Net mask is 255.255.255.0, Gateway is 192.168.1.1, DNS address is the value
provided by ISP).
Figure 3-1
Please note:
Users of Windows 98 can open TCP/IP Properties according to the following: Right-click
(Mouse) Network Neighbor -> Choose Properties -> Double-click TCP/IP PCI Fast
Ethernet Adapter.
- 7 -

TD-8811 External ADSL2+ Router User Guide
The users of Windows 2000/NT/XP can do the following: Right-press Network Neighbor
->Choose Properties->Right-press Local Connection ->Choose Properties->Double-
click Internet Protocol (TCP/IP).
NOTE: The words in fact may be different with this guide.
Remarks: you can check whether your configuration is successful through PING
command. Enter Ping 192.168.1.1
If the screen looks like the following, you have been successful.
Pinging 192.168.1.1 with 32 bytes of data:
Reply from 192.168.1.1: bytes=32 time<10ms TTL-128
…
If the screen looks like the following, the connection has failed. Please try again.
Pinging 192.168.1.1 with 32 bytes of data:
Request timed out.
3.2 Login
Startup Internet Explorer, and enter 192.168.1.1;then enter default user name(admin)、
password(admin), When ADSL2+ connection is OK, you will see the Figure 3-2.
Figure 3-2
- 8 -