TP-Link Archer VR600v User manual

YOUR NEW MODEM SUPPORTS:
•ADSL / ADSL2 / ADSL2+
•VDSL2
•UFB
•3 x 10/100/1000 LAN ports
•1 x 10/100/1000 WAN/LAN port
•802.11 b/g/n/ac Wi-Fi
•Up to 300Mbps on 2.4 GHz
+ 1300Mbps on 5 GHz
•2 x VOIP phone ports
•1 x USB port
SUPPORT & WARRANTY
3 Years Manufacturer’s Warranty
Website: http://www.tp-link.com/support
Email: [e-mail]
24/7 Helpline: 0800 875 465

GETTING STARTED
This quick start setup guide is to help you get up and running on your new Unlimited
Internet connection.
Before you start please check you have the following items:

INSTALLING YOUR NEW
TP-LINK VR600v WIRELESS ROUTER
Step 1: Open your box and pull out the modem. Make sure you have your username
and password, we sent to you via email handy as you will need this when you reach
step 9.
Step 2: Connect the power adapter to an unused socket on your wall, with the other
end going into the port on your modem labeled ‘Power’.
Step 3: Plug the ethernet cable into the GE1 / LAN1 port on the Fibre box and the
other end to the LAN4/WAN port at the back of the modem
Step 4: Make sure to press the power button, located to the side, and ensure your
Power LED begins to glow.
NOTE:If your modem was sent out by us, it will be preconfigured and you can
just plug it in and it’s ready to go.

LOGGING INTO YOUR ROUTER
Step 5: You need to now connect to your router. This can be done either via an
Ethernet cable or via Wi-Fi.
Ethernet: Take the Ethernet cable and plug one end into the port labelled LAN1 at
the rear of your modem with the other end going into your laptop or desktop
computer’s Ethernet port. Wait for a minute while your computer connects to your
modem.
Wi-Fi: Once your router is turned on it automatically broadcast a Wi-Fi signal.
Connect to the Wi-Fi Network name (SSID) as printed on the bottom of the modem
as well as your TP-Link Wi-Fi card It should be similar to : “TP-Link_xxxx”. The
default Wi-Fi password is also printed at the bottom of the modem and on the wifi
card as well.
Step 6:Once the connection is made, open a web browser (Chrome, Firefox etc.) &
enter http://192.168.1.1 into the address bar as shown below. Once done press
enter, you will immediately be prompted to setup a new password for the first time.
Please enter your desired password and save it somewhere secure. You will require
this password every time you want to log in to your router.

CONFIGURING YOUR ROUTER
Once you have logged into your modem following the “Logging into your Router”
instructions, you can now begin to configure your router.
Step 7: Click on the Advanced tab and go to Operation Mode.
Step 8: Under Operation Mode select “Wireless Router Mode” and click Save.
(The modem will reboot after this then you will need to log in again)

Step 9: Next click Advanced on the bar up to top, then click Network on the left
then click – Internet
Step 10:Under “Internet Connections” click +Add button.
Step 11:Ensure Settings are as below:
VLAN ID: Enabled
VLAN ID: 10
Internet Connection Type: PPPoE
Username: (enter your PPP Username here)
Password: (enter your PPP Password here)

Step 5.7: Click Save
Your modem should now be configured for Fibre

1. CONFIGURING YOUR WIFI NETWORK
NAME & PASSWORD
Once you have successfully logged into the modem, Lets set up your Network Name
(SSID) & Password.
Step 6.1:Click on “Basic” tab up at the top, then click the “Wireless” tab on the left.
You will now be displayed the Wireless Settings page.
Step 6.2: Ensure the checkboxes besides 2.4 GHz or 5GHz Wireless Network are
checked.
Step 6.3: Here you can also change your wireless network name and password to
your desired name and password. Then click “Save”.
Note: If you use a wireless device to change the wireless settings, you will be disconnected after the new
settings are effective. Please write down the new SSID and password for future use.
Step 6.4: Congratulations you have now completed your configuration is complete,
Your Wifi is now secured. You can now connect to your WiFi devices using the
details you have just configured.