TPL VISION SCOA55 User manual

INTRODUCTION
INTRODUCTIONINTRODUCTION
INTRODUCTION
This note contains all the instructions and precautions for a safe set up and an optimal use of the product.
Warning: we are not responsible if an of these items below would not be respected and in this case, the TPL Vision’s
warrant shall not appl an more to this product.
USER’S GUIDE
SCOA55 (High Power)
Rev A cop right TPL Vision ©
Rev A cop right TPL Vision ©Rev A cop right TPL Vision ©
Rev A cop right TPL Vision © 1/2
1/21/2
1/2
SET UP PROCEDURE
SET UP PROCEDURESET UP PROCEDURE
SET UP PROCEDURE
Lighting shall not be settled while the pro-
duct is powered on.
For the screws selection (not included) res-
pect the following indications :
Recommended torque: 0.5 to 1.5 Nm (Using
LOCTITE 243 (not supplied) is recommended)
PACKAGING /
PACKAGING / PACKAGING /
PACKAGING / SHIPPING
SHIPPING SHIPPING
SHIPPING /
/ /
/ RECEPTION
RECEPTIONRECEPTION
RECEPTION
The product is packaged in our factor using appropriate boxes and packages. The are made to avoid an damages b
means of regular transportation.
However a damaged parcel should be reported to the carrier upon receipt and stated officiall at its reception (as a
"reserve"). Then, please report b writing to TPL VISION as soon as possible. (at least within 24 hours after the package
reception). An package damaged during transportation will not be taken back or replaced if it has not been reported
on the travel voucher and to TPL VISION on time.
When ou open the bag containing the product, an cutting blade should be avoided so as not to damage the product.
All accessories included in the package must be used if necessar (do not use other products or equivalent to replace
the accessories supplied).
SAFETY AND OPERATING INFORMATION
SAFETY AND OPERATING INFORMATIONSAFETY AND OPERATING INFORMATION
SAFETY AND OPERATING INFORMATION
Class III light
IP class of the product: see the product presentation
Operating temperature 0°C à 40°C
Power suppl 24VDC+/- 10%, if this is not respected, ou ma damage the product and/or the user ma be
electrocuted
Observe the power suppl voltages and terminal plug in
Do not modif the product even partiall
Do not clean while operating
Do not cover with a heat insulation or do not lock in a sealed area
Do not stare into the beam and follow the instructions below:
• If possible set up a filter to block the product’s light radiation between the lighting product and the surrounding
worker
• When the implementation of a filter is not possible, provide glasses or an adequate protection mask to workers in
order to block the light radiation
• Forbid or limit as possible direct access to the light source (exposure in the axis of radiation)
• Point out a securit area to prevent workers from getting too close to the light; please follow the NZOR (Nominal
Zone of Optical Risk) recomandations given b TPL Vision (upon demand)
In an case, ensure that workers around the product are properl protected toward exposure

ELECTRICAL WIRING
ELECTRICAL WIRINGELECTRICAL WIRING
ELECTRICAL WIRING
1– Turn off overall s stem 24 VDC power suppl
2– Make all connections (power off) regarding
diagram(s) below:
CLEANING (PRODUCT
CLEANING (PRODUCT CLEANING (PRODUCT
CLEANING (PRODUCT TURNED
TURNEDTURNED
TURNED OFF):
OFF):OFF):
OFF):
Use a soft, dr cloth.
Do not use solvents or chemicals.
Do not use abrasive cleaning products.
Rev A cop right TPL Vision ©
Rev A cop right TPL Vision ©Rev A cop right TPL Vision ©
Rev A cop right TPL Vision © 2/2
2/22/2
2/2
Wiring Diagram when using
a STRTPL1000 drive
Please see the STRTPL drive user guide
Wiring Diagram when using
another power drive
To know the proper
power drive caract he-
ristics, please see the
S OAX sale documen-
tation.
WARNING
WARNINGWARNING
WARNING
The SCOAX is ver high power light (12 high power LED inside).
His design do not accept a continuous mode
not accept a continuous mode not accept a continuous mode
not accept a continuous mode running—please see the sale documentation
for proper utilisation, or ask directl to TPL Vision technical department.
His design don’t include control current drive—don’t connect the SCOAX directl to the
24V—absolutl use the proper drive advised b TPL Vision