TracVision A5 User manual

Replacement Remote Control Instructions
54-0223 Rev. B 1
TracVision®A5 Replacement
Remote Control Instructions
The following pages explain how to quickly start using your
replacement TracVision A5 remote control.
Installing the Remote Control Batteries
To install the remote control’s batteries, follow the steps below.
1. Remove the battery compartment cover, located on
the back of the remote control.
2. Insert two “AAA”-size batteries as shown,
observing the correct polarity.
3. Replace the battery compartment cover.
Programming the Remote Control to Operate
a Second Receiver
(If Applicable)
The replacement remote control is programmed to work with the
receiver that came with your TracVision antenna. If you have a
second receiver installed, and you need to use the replacement
remote control to operate that second receiver (and not the
original receiver), follow the steps below to program the
replacement remote control.
1. Press and hold the SAT button.
2. At the same time, press the MUTE button for two
seconds.
3. Release both buttons. The SAT button should
remain lit. If it doesn’t, repeat Steps 1 and 2.
4. Using the numeric keypad, enter “002”.
5. Press the SAT button to lock in the code.
6. Press the SELECT button twice.
7. The remote control should now be programmed to
operate the second receiver.
CHVOL
PWR
DVD VCR AUX TV SAT
GUIDE
MENU
INFO CLEAR
TURBO FAV
MUTE CH
PREV
DIRECTOR
PROG
SEARCH AUDIO
VIDEO
123
456
789
0
INPUT
REW PLAY FF
REC STOP PAUSE
P
A
G
E
O
N
E
L
I
N
E
G
U
I
D
E
SELECT
If you will be using the replacement remote control to
operate the original receiver, you do NOT need to
program the remote control.

Programming the Remote Control to Operate
Other Vehicle Components
(Optional)
In addition to controlling the satellite receiver, you may be able
to operate your vehicle’s TV, VCR, DVD, or AUX components
using your new TracVision remote control. To program your
remote control, choose either of the following programming
options:
Option 1 - Code Scanning - See the procedure below.
Option 2 - Code Entry - See the TracVision A5
Installation Guide for details.
Code Scanning
1. Keep your remote control aimed at the IR input
(or “eye”) for the component you want to control.
For example, if you want to program the remote
control to operate your TV, keep the remote aimed
at the TV’s IR input (many in-vehicle TVs come
with an IR eye built into the screen).
2. Press and hold the remote control’s component
button (for example, TV).
3. At the same time, press the MUTE button for two
seconds.
4. Release both buttons.
The component button should light and remain lit.
If it doesn’t remain lit, repeat Steps 1 through 4
above.
5. Repeatedly press the upper part of the CHANNEL
(CH) button.
6. Continue pressing the CHANNEL (CH) button to
step through the codes until the component turns
off, indicating that you have found the correct
device code. If you accidentally pass a code that
responds or realize you may not have been aiming
the remote control at the component, repeatedly
press the lower part of the CHANNEL (CH)
button to step backward through the codes.
54-0223 Rev. B
2
TracVision A5
To use the code entry method, you’ll need to know the
correct manufacturer’s device codes for each component
you want to operate. Code scanning may be more time-
consuming, but you don’t need to know the
manufacturer’s control codes.
CH P
A
G
E

7. Press the remote control’s POWER button to verify
that you have found the proper code. The correct
code will turn the component on and off.
8. Press the component button again to lock in the
code (in this example, the TV button).
Replacement Remote Control Instructions
54-0223 Rev. B 3
For complete instructions on how to use the remote
control, refer to the TracVision A5 User’s Guide.