Traditional Tool Repair MUL-370 User manual

No KEY No PARTDESCRIPTIONQTY.
1ELDNAH10-0731
1LWAPNOISNET20-0732
2NIP30-0733
1LEEHWTEHCTAR40-0734
1RELLOR50-0735
1NIPRELLOR60-0736
1REVEL70-0737
1GNOLLWAP80-0738
1TROHSLWAP90-0739
1REVELRETTUC01-07301
1GNIRPSREVEL11-07311
1EMARF21-07321
1DAPREPPIRG31-07331
1GNISUOHRETTUC41-07341
1RETTUC51-07351
1SSALDNIW61-07361
1GNIRPS71-07371
1TFAHSTOOFREPPIRG81-07381
1RELLORTOOFREPPIRG91-07391
1TFAHSCIRTNECCE02-07302
1REDLOHREPPIRG12-07312
1GNIRPSTOOFREPPIRG22-07322
1)"4/3(GNIRGNINIATERE32-07332
24 370-24WASHER 5х11х17.0
1TOOFREPPIRG52-07352
1REHSAW62-07362
1REVELYRAILIXUA72-07372
1GNIRPSYRAILIXUA82-07382
3GNIRPSLWAP92-07392
1BONK03-07303
1"61/5GNIRPILK13-07313
18x2,1NIPRETTOC23-07323
33 370-33 SET SCREW М6х12 DOG POINT 3
18,11x4RELLORELDEEN43-07343
1"8/5GNIRPILK53-07353
2"61/5x"8/1NIPGNIRPS63-07363
1GNIRAEBENALP73-07373
38 370-38SET SCREW М5х8 HALF DOG POINT 1
39 370-39 COUNTERSUNK HEAD SCREW M5x8 2
40 370-40 SET SCREW М5х16
18REHSAW14-07314
1LLAMSGNIRAEBENALP64-07364
28
46
1
20
38
21
4025
17
16
15
19
29
18
14
37
13
12
10
11
26
9
8
7
27
5
32
4
6
41
23
39
2
22
35
30
3
34
24
MUL-370
31
for PET Strapping
Heavy Duty Tensioner
36
33
3
WWW.TRADITIONALTOOL.COM
For Parts & Service 1-877-862-6699

Fig. 1 –Starting Position
1. Raise Gripper Foot 25 by pressing down on Tension Handle 01. Load bottom strap 101 under Cutter
Housing 14, under Gripper Foot 25 and leave at least 2” of the strap extended out from the front of the
tool for seal placement as shown on Fig. 2.
Fig. 2
2. Load upper strap 100through Cutter Housing 14, through Windlass 16 as shown on Fig. 3.
Fig. 3
WWW.TRADITIONALTOOL.COM
For Parts & Service 1-877-862-6699

3. Apply tension by ratcheting Tension Handle 01 as shown on Fig. 4.
Fig. 4
4. Once satisfactory tension is achieved the strap is ready to be sealed. With the Seal 103 securely in
place use the appropriate Sealer 104 to snap the Seal 103. Place the Jaws 105 of the sealer on the
middle of the Seal 103 and press the Handles 106 until they cannot be squeezed any further. Then
unclenched the Handles 106 and remove the Sealer 104 as shown on Fig. 5
Fig. 5
WWW.TRADITIONALTOOL.COM
For Parts & Service 1-877-862-6699

5. Once the joint is secure the strap is ready to be cut. Push down on the Tension Handle 01 until the
strap is cut and slide the tensioner to the right to release the strap from under the Gripper Foot 25 as
shown on Fig. 6. The operation cycle is now complete.
Fig. 6
WWW.TRADITIONALTOOL.COM
For Parts & Service 1-877-862-6699