Traditional Tool Repair DSA-116 Instruction Manual

DSA-116 & DSA-218 MANUAL SEALERS
DSA-116 (Part No. 306180) !
!!
!DSA-218 (Part No. 306190)
TOOL SPECIFICATIONS
MODEL
(Part No.)
STRAP
TYPE WIDTH THICKNESS SEALS
DSA-116
(306180)
High Tensile
3/4" .025 to .031 637, 482-12
DSA-218
(306190) 1 1/4" .025 to .035 1032, 1032PBH, 1037
GENERAL SAFETY CONSIDERATIONS
1. EYE INJURY HAZARD.
Failure to wear safety glasses with side shields
can result in severe eye injury or blindness.
Always wear safety glasses with side shields
which conform to ANSI Standard Z87.1.
2. STRAP BREAKAGE HAZARD.
Improper operation of the tool or sharp corners
on the load can result in strap breakage during
tensioning, which could result in the following:
P
PP
PA sudden loss of balance causing you to fall.
P
PP
PBoth tool and strap flying violently towards
your face.
Failure to place the strap properly around the
load or on an unstable or shifted load could
result in a sudden loss of strap tension during
tensioning. This could result in a sudden loss of
balance causing you to fall.
Read the tools operating instructions. If the load
corners are sharp use edge protectors. Place the
strap correctly around a properly positioned load.
Positioning yourself in-line with the strap, during
tensioning and sealing, can result in severe
personal injury from flying strap or tool.
When tensioning or sealing, position yourself to one
side of the strap and keep all bystanders away.
3. FALL HAZARD.
Maintaining improper footing and/or balance
when operating the tool can cause you to fall. Do
not use the tool when you are in an awkward
position.
4. CUT HAZARD.
Handling strap or sharp parts could result in cut
hands or fingers. Wear protective gloves.
5. TRAINING.
This tool must not be used by persons not
properly trained in their use. Be certain that you
receive proper training from your employer. If
you have any questions contact your Acme
Representative.
6. TOOL CARE.
Take good care of the tool. Inspect and clean it
daily, lubricate it weekly and adjust when
necessary. Replace any worn or broken parts.
7. WORK AREA.
Keep work areas uncluttered and well lighted.
OPERATION,PARTS
AND SAFETY MANUAL
WWW.TRADITIONALTOOL.COM
For Parts & Service 1-877-862-6699

OPERATING INSTRUCTIONS
1. Fully open the sealer handles and center the open jaws on the seal. See Figure 1.
2. Bring the sealer handles together completely together to assure a proper notch. See Figure 2.
3. Remove the sealer. Place the sealer on the opposite end of the seal and bring the handles completely together.
Remove the sealer.
NOTE: If the gauge of the strap being used will not allow it to be bent, cut the strap supply as close to the seal
as possible using an approved strap cutter.
4. To avoid contact with the sharp end of the strap, retract the strap end back into the strap dispenser.
PARTS LIST
DSA116 DSA218
KEY QTY. PART# PART# DESCRIPTION
1 3 003911 003911 Flexloc nut, thin, 5/16-24 When ordering parts, please show tool
2 2 004033 003971 Side plate model, part number and name.
3 4 004037 003974 Jaw pin
4 4 004039 003977 Jaw All recommended spare parts are
5 2 004038 003976 Notcher pin underlined and should be stocked.
6 2 004041 003991 Notcher
7 1 306183 306193 Upper handle assembly Standard hardware parts may be obtained
8 4 004036 003973 Link pin from local hardware suppliers.
9 1 003907 003907 Rear link
10 1 003906 003906 Front link
11 3 004034 - HHCS, 5/16-24 x 1 7/16
3 - 003972 HHCS, 5/16-24 x 1 5/8
12 2 082630 082630 Grip
13 1 306184 306194 Lower handle arm assembly
14 1 003132 003132 Caution plate
15 1 584-1172 584-1162 Nameplate
For Parts Support Call 1-877-862-6699
MAINTENANCE
Inspect tool daily for worn or broken parts and
replace if necessary. Clean and apply light machine
oil to all moving parts - weekly.
WWW.TRADITIONALTOOL.COM
For Parts & Service 1-877-862-6699