TrailFX JL010RI User manual

www.TrailFX.com
Page 1 of 4 Rev061720
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT.
READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
DO NOT OVER TORQUE. USE STANDARD OPERATING LOAD FOR
TIGHTENING BODY MOUNT NUTS & BOLTS VARIES
60-180 min
[e-mail]
1 866 638 4870
POLISHED STAINLESS STEEL –LIMITED LIFETIME
POWDER COATED BLACK –3 YEARS
Cutting Not
Required
PARTS LIST:
Qty
Part Description
Qty
Part Description
1
Driver/Left Fender Liner
6
6mm Clip Nuts
1
Passenger/Right Fender Liner
1
4mm Hex Wrench
18
6-1.0mm x 20mm Button Head Combo Bolts
PROCEDURE:
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS
CAREFULLY. ASSISTANCE IS RECOMMENDED.
1. Start installation in the Driver/Left wheel well. Locate the tabs along the bottom of the wheel well
above the frame, (Figure 1). NOTE: The factory fender liner is attached to these tabs.
2. Select (3) 6mm Clip Nuts. Slide the Clip Nuts onto the (3) inner mounting tabs, (Figure 1).
3. Select the Driver/Left Rear Fender Liner. Insert the Fender Liner into position up to the back of the
inner body panel. IMPORTANT: If the vehicle has aftermarket fenders previously installed, it may be
necessary to temporarily remove any hardware interfering with the Fender Liners. NOTE: It may be
easier to install the Fender Liner with the vehicle raised up and/or rear tire removed.
4. Attach the bottom of the Fender Liner to the (3) 6mm Clip Nuts with (3) 6mm Button Head Combo
Bolts, (Figure 2). Do not tighten hardware.
REAR FENDER LINERS
Part No. JL010RI
Fits: Current JEEP GLADIATOR
Driver/Left
Fender Liner
Passenger/Right
Fender Liner
Front
Drilling Not
Required

www.TrailFX.com
Page 2 of 4 Rev061720
(Fig 2) Attach the Liner to the inner
body panel. (NOTE: Slide the (3) Clip
Nuts onto the panel first)
5. Attach the Fender Liner to the (6) mounting locations with (6) 6mm Button Head Combo Bolts,
(Figures 3—5). Do not tighten hardware.
6. Align and adjust the Fender Liner. Fully tighten all hardware attaching the Fender Liner and fender.
7. Repeat Steps 1—6for Passenger/Right side Fender Liner installation.
8. Do periodic inspections to the installation to make sure that all hardware is secure and tight.
To protect your investment, Do not use any type of polish or wax that may contain abrasives that could damage the
finish. Mild soap may be used to clean the Fender Liners.
Driver/Left Side Installation Pictured
(Fig 1) Remove the factory clip nuts and
slide (3) 6mm Clip Nuts onto the (3)
mounting holes inside the wheel well
Front
Front
Front
(Fig 3) Fender Liner will attach to the (6)
factory locations (arrows). Attach the
Fender Liner to these mounting points
(3) 6mm Button Head Combo Bolts
(3) 6mm Clip Nuts

www.TrailFX.com
Page 3 of 4 Rev061720
(3) 6mm Button Head
Combo Bolts
(3) 6mm Button Head
Combo Bolts
(Fig 4) Attach the front of the
Fender Liner to the wheel well
(Fig 5) Attach the rear of the
Fender Liner to the wheel well
Front
Front

www.TrailFX.com
Page 4 of 4 Rev061720
FAQ’s
1. Hardware’s are not of correct size.
In GMC / Chevrolet truck model 2006 & up, customer needs to reuse the factory body bolts to install the bracket. If your vehicle is not
GMC / Chevrolet 2006 & up, ensure that holes are not partially covered with any plastic grommet or rust? If it is, remove the plastic
grommet & rust from the thread holes & re-try the installation.
2. Mounting Bracket are not getting Installed properly.
In some cases Illustration images shown in Installation manual may not be the exactly same as per actual vehicle images ,also if Driver /
Passenger side mounting brackets are very identical in the design, suggest referring Parts Identification guide to avoid fitment issue.
3. Products are thumping / rattling after installation.
Ensure that all required mounting brackets / hardware’s are installed & tighten correctly. Suggest using white lithium / regular grease
between the metal to metal contact surfaces.
4. Side Bar is not aligning with vehicle / Step Pads are not aligning with vehicle doors.
Side bar may be interchanged or mounting brackets are not installed at the correct position in the vehicle. Refer Parts identification
guide.
5. Missing / Excess Hardware.
Recheck hardware count as per the part list.
6. Product not installing properly.
Ensure make model year, cab length and bed size of your vehicle is listed in the application. All installation steps are followed correctly.
Check out these other TrailFX Products!! www.TrailFX.com
PRODUCT CARE
Periodically check the product to ensure all fasteners are tight and components are intact.
Regular waxing is recommended to protect the finish of the product.
Use ONLY Non-Abrasive automotive wax. Use of any soap, polish or wax that contains an abrasive is detrimental and can scratch the
finish leading to corrosion.
Aluminum polish may be used to polish small scratches and scuffs for Stainless Steel finish.
Mild soap may be used to clean the product for both Stainless Steel and Black finish.
Keystone Automotive Operations Inc. (KAO) warrants this product to be free of defects in material and workmanship at the time of purchase by the
original retail consumer. KAO disclaims any other warranties, express or implied, including the warranty of fitness for a particular purpose or an
intended use. If the product is found to be defective, KAO may replace or repair the product at our option, when the product is returned prepaid,
with proof of purchase. Alteration to, improper installation, or misuse of this product voids the warranty. KAO’s liability is limited to repair or
replacement of products found to be defective, and specifically excludes liability for any incidental or consequential loss or damage.