TrailFX J042T User manual

www . T r a il F X . c om
Page 1of 4 Rev 053118
.
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT.
READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
PLEASE USE SAFETY GLASSES & ENSURE TO BLOCK VEHICLE
MOVEMENT DURING INSTALLATION PROCESS
60-180 min
[e-mail]
1 866 638 4870
POLISHED STAINLESS STEEL –LIMITED LIFETIME
POWDER COATED BLACK –3 YEARS
Cutting Not
Required
PARTS LIST
Qty
Part Description
Qty
Part Description
1
Jack Mount
INSTRUCTION PROCEDURE
1. To ensure safety in use, please regularly check Jack Mount and all the parts connecting with car body for loose connections;
clean the Jack Mount periodically
Off Road Jack Mount
Part: J042T
Fit: 2007 - Current Jeep Wrangler JK
Drilling Not
Required
Remove the OEM Decorative Cover
Remove the OEM Screws

www . T r a il F X . c om
Page 2of 4 Rev 053118
Connect mounting bracket with the car body and tighten with one outside hexagon bolt, M10 flat washer and one circular tube.
Install the mounting bracket on upper mounting plate and tighten with Cylinder head hex socket bolt and flat washer
Install the block rubber on mounting bracket and upper mounting plate with Round head bolt of a cross and nut, respectively.
Place the jack on mounting bracket and fixed with under mounting plate, handle nut and Non-slip gasket.

www . T r a il F X . c om
Page 3of 4 Rev 053118
Install the Jack on mounting bracket with handle bolt and Non-slip gasket.
Installation Complete

www . T r a il F X . c om
Page 4of 4 Rev 053118
PRODUCT CARE
1. Periodicallycheckthe product toensure allfasteners aretightandcomponents are intact.
2. Regular waxingis recommended to protect thefinish of the product.
3. Use ONLY Non-Abrasive automotive wax. Use of anysoap, polish or wax thatcontains an abrasiveis detrimental and
Can scratch thefinishleadingtocorrosion.
4. Aluminumpolishmaybe used to polish small scratches andscuffs for Stainless Steel finish.
5. Mild soap may be used to cleantheproduct forboth Stainless Steel and Black finish.
Check out these other TrailFx Products!! www.TrailFX.com
FAQ’s
1. Hardware’s are not of correct size.
In GMC / Chevrolet truck model 2006 & up, customer needs to reuse the factory body bolts to install the bracket. If your vehicle is not
GMC / Chevrolet 2006 & up, please ensure that holes are not partially covered with any plastic grommet or rust? If it is, please remove
the plastic grommet & rust from the thread holes & re-try the installation.
2. Mounting Bracket are not getting Installed properly.
In some cases Illustration images shown in Installation manual may not be the exactly same as per actual vehicle images ,also if Driver /
Passenger side mounting brackets are very identical in the design, suggest referring Parts Identification guide to avoid fitment issue.
3. Products are thumping / rattling after installation.
Please ensure that all required mounting brackets / hardware’s are installed & tighten correctly. Suggest using white lithium / regular
grease between the metal to metal contact surfaces.
4. Side Bar is not aligning with vehicle / Step Pads are not aligning with vehicle doors.
Side bar may be interchanged or mounting brackets are not installed at the correct position in the vehicle. Please refer Parts
identification guide.
5. Missing / Excess Hardware.
Recheck hardware count as per the part list.
6. Product not installing properly.
Ensure make model year, cab length and bed size of your vehicle is listed in the application. All installation steps are followed correctly.
Keystone Automotive Operations Inc. (KAO) warrants this product to be free of defects in material and workmanship at the time
of purchase by the original retail consumer. KAO disclaims any other warranties, express or implied, including the warranty of
fitness for a particular purpose or an intended use. If the product is found to be defective, KAO may replace or repair the product
at our option, when the product is returned prepaid, with proof of purchase. Alteration to, improper installation, or misuse of this
product voids the warranty. KAO’s liability is limited to repair or replacement of products found to be defective, and specifically
excludes liability for any incidental or consequential loss or damage.