TrailFX DHS001B User manual

Page 1 of 4
TrailFX Drop Down Step
Part No. DHS001B / DHS002B
Fits: 2015-2019 Chevrolet, GMC / Colorado / Canyon Crew
Cab & Ext Cab
Product image
TO AVOID BEING SCRATCHED, PLEASE PROTECT THE SURFACE OF
THE TAILGATE VENT COVER CAREFULLY.
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT.
PARTS LIST:
Item Qty Part Description Tools Needed
11Step Bar Driver Side 13 MM SOCKET & WRENCH
21Step Bar Passenger Side 14 MM SOCKET & WRENCH
33Mounting Bracket Driver Side 15 MM SOCKET & WRENCH
43Mounting Bracket Passenger Side RATCHET
512 M8 Bolt TORQUE WRENCH
612 M8 Lock Washer
712 M8 Flat Washer
812 M10 Flange Bolt
912 M10 Flange Nut
10 12 M8 Nut Clip
ALIGN THE STEP BARS AS DESIRED AND TIGHTEN ALL M10 FASTEN-
ERS TO 30 ft. - lbs., AND THE M8 FASTENERS TO 15 ft.-lbs.
READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
60 min Drilling Not
Required
Cutting Not Re-
quired
Mounting Kit Images
ITEM 4
ITEM 3

Page 2 of 4
5. Grab Driver Side Bar and install loosely to mount
brackets with (6) M10 Flange bolts and (6) Serrated
Flange Nuts. See Figure 3.
6. Repeat for passenger side.
7. Align and adjust the step bars as needed and fully
tighten all hardware.
8. See Figure 4 for reference.
1. Remove plastic plugs from rocker panel.
INSTALLATION PROCEDURE
FIGURE
89
Figure 1
Remove Plastic Plugs
10
5
6
7
2. Start at the front driver side of vehicle and grab (2) M8
Nut clips (2) M8 hex head bolts, (2) M8 flat washer, and
(2) M8 lock washer to driver mount bracket to rocker
panel. Assemble loosely. See Figure 1 and 2.
3. Repeat for center and rear locations.
4. Repeat for passenger side.

Page 3 of 4
COMPLETE INSTALLATION
FIGURE 9
DRIVER SIDE SHOWN FRONT
Item 3 Item 3 Item 3

Page 4 of 4
Keystone Automotive Operations Inc. (KAO) warrants this product to be free of defects in material and workmanship at the time of pur-
chase by the original retail consumer. KAO disclaims any other warranties, express or implied, including the warranty of fitness for a
particular purpose or an intended use. If the product is found to be defective, KAO may replace or repair the product at our option,
when the product is returned prepaid, with proof of purchase. Alteration to, improper installation, or misuse of this product voids the
warranty. KAO’s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for any
incidental or consequential loss or damage.
Check out these other TrailFX Products!!
PRODUCT CARE
1.
FAQ’s
1. Mounting bracket are not getting Installed properly.
In some cases Illustration images shown in Installation manual may not be the exactly same as per actual vehicle images ,also if Driver / Passenger side
mounting brackets are very identical in the design, suggest referring Parts Identification guide to avoid fitment issue.
2. Products are thumping / rattling after installation.
Please ensure that all required mounting brackets / hardware’s are installed & tighten correctly. Suggest using white lithium / regular grease between the
metal to metal contact surfaces.
3. Missing / Excess Hardware.
Recheck hardware count as per the part list.
4. Product not installing properly.
Ensure make model year, cab length and bed size of your vehicle is listed in the application. All installation steps are followed correctly.
Learn more about running boards on our website.