TRAK RACER MS-SML-FM User manual

1
Published 2023‑09‑06
Floor Single Monitor
Stand with VESA Mount
(800mm Crossbar)
Assembly Guide
MS-SML-FM
IMPORTANT: As there are different versions of each rig depending on your
region, please ensure that you are using the correct instruction set. The
part number below should match the part number labeled on your box

2
3 Symbol Legend
4 Part list
5 Assembly Notes
9 MS-SML-FM Assembly Instructions
TABLE OF CONTENTS

3
Two people needed
Tighten hardware
Leave hardware loose for adjustment
Make Adjustment
Break tab off Corner bracket CB1
Safety glasses needed
Attention / Priority
Reserve for following step
Mirrored Components (Same on both sides)
IMPORTANT: As there are different versions of each rig depending on your
region, please ensure that you are using the correct instruction set. The
part number below should match the part number labeled on your box
IMPORTANT: Due to the nature of cut aluminium prole, some metal
shavings may still be present after our extensive QA cleaning process. We
recommend that boxes and packaging is opened on a hard oor.
NOTE: Some screws and washers are pre-installed. These will be part of
the parts list and will need to be loosened and reattached according to
the instructions.

4
If you have any issues, please contact us at [e-mail]
*NOTE: Extra hardware may be included as spare parts
IMPORTANT: As there are different versions of each rig depending on your
region, please ensure that you are using the correct instruction set. The
part number below should match the part number labeled on your box
MS-SML-FM PARTS LIST
Part # Description QTY Check
BOX #: TR80-FMMS5-BLK
PS-600-R Prole strip, 600mm Red 2
PS-1200-R Prole strip, 1200mm Red 2
BC-40 Bracket, Corner with Cap, 40x40 4
BA-80-BLK Bracket, Anodized corner, 40x80, Black 4
BA-40-BLK Bracket, Anodized corner, 40x40, Black 4
EC-80 End Cap, 40x80 6
BP-80-V Bracket (Plate), 80, Vertical 2
NS-M8 T-Nut (Spring), M8 44
AL-80-1200 Aluminum Prole, 40x80x1200mm 2
AL-80-600 Aluminum Aluminum Prole, 40x80x600mm 2
AL-80-105 Aluminum Prole, 40x80x105mm 2
SH-M8-16 Screw (Hex), M8x16 24
SH-M8-20 Screw (Hex), M8x20 20
WF-M8 Washer (Flat), M8 20
WL-M8 Washer (Lock), M8 20
OPTIONAL
FR-01 Feet, Rubber 4
NS-M6 T-Nut (Spring), M6 4
SH-M6-20 Screw (Hex), M6x20 4
BOX #: TR80-TMSML3-BLK
BA-80-BLK Bracket, Anodized corner, 40x80, Black 2
EC-80 End Cap, 40x80 2
NF-M8 Nut (Flange), M8 8
NS-M8 T-Nut (Spring), M8 11
AL-80-800 Aluminum Aluminum Profile, 40x80x800mm 1
SF-M8-16 Screw (Flat), M8x16 8
SH-M8-16 Screw (Hex), M8x16 8
SH-M8-20 Screw (Hex), M8x20 3
VM-02 VESA new 1
WF-M8 Washer (Flat), M8 3
WL-M8 Washer (Lock), M8 3

5
1
NOTE
FRONTSIDE
INSIDE
TOP SIDE
BACK SIDE
OUTSIDE
a
a
a
x
x
x
INSTALLATAION ORDER FOR SCREWS & WASHERS HOW TO MEASURE SCREWS
①SCREW ②LOCK WASHER
(IF APPLICABLE)
③WASHER
FLAT SCREW
HEX SCREW
BUTTON SCREW

6
NOTE
The handle screws (SL-M8-20 & SL-M8-25) are
ratcheted to allow for tightening and loosening
when space for rotation is limited. Simply pull the
handle out and turn handle into position and
push handle back in to engage thread.

7
NOTE
tooltip
tooltip
tooltip
tooltip
If T-Nuts are skipped, and
the ends are no longer
accessible, they can be
inserted by “rocking” them
in from the outer face as
shown.
Use the provided allen key
to push the T-Nut into
position and place the hole
to slide into position.
It is strongly advised that
spring T-Nuts are inserted by
sliding from the ends of
profiles. Please take careful
note of each step of all T-nuts
as some are to be installed in
anticipation of future steps.
NS-M8 & NS-M6

8
NOTE BC-40

tooltip
370mm
tooltip
9
tooltip
tooltip
b
1
2
M6x16mm
SH-M6-16 x4
a b
Insert 4pcs of NS-M8 into
OUTSIDE of each of
AL-80-600 (for STEP 2b)
a
BP-80-V x2
Insert 1pcs of NS-M8 into
FRONT & BACK SIDE of each
of AL-80-1200 (for STEP 3)
NOTE: Rubber feet and hardware are optional.
AL-80-600 x2 NS-M8 x8
AL-80-1200 x2 WL-M8 x12 WF-M8 x12 NS-M8 x8 SH-M8-20 x12
M8x20mm
NS-M6 x4 FR-01 x4

tooltip
tooltip
tooltip
10
3
BA-40-BLK x4
4
ba
WL-M8 x8 WF-M8 x8 NS-M8 x12 SH-M8-20 x8
M8x20mm
BC-40 x4
AL-80-105 x2 NS-M8 x8
M8x16mm
SH-M8-16 x8

tooltip
11
tooltip
600mm
60mm
60mm
AL-80-800 x1 NS-M8 x8
M8x16mm
SH-M8-16 x8
6
BA-80-BLK x2
5
Ensure corner brackets
are facing inward
NS-M8 x4
M8x16mm
SH-M8-16 x4

tooltip
12
7
VM-02 x1
8NOTE: Optional for larger monitors.
NS-M8 x8 SH-M8-20 x3
M8x20mm
WL-M8 x3 WF-M8 x3
M8x16mm
SF-M8-16 x8 NF-M8 x8 VM-02-A x2 VM-02-B x2
If monitor mounting points are
150mm or 200mm apart, add
VESA extensions (VM-02-E)

13
tooltip
tooltip
9
10
NOTE: If installing Arms for triple monitors, skip this step
until assembly of all other components is complete.
NOTE: Tape measure and scissors not supplied
BC-40 x4
EC-80 x8
PS-1200-R x2 PS-600-R x2

14
IMPORTANT: If your monitor screws are under 8mm
(M8), you will need to use washers (not supplied)
11
tooltip

15
Share your build online and tag us to be featured!
@trakracer @trakracer @trak_racer
FINISHED