MINOURA P-600AL CLOSET-CYCLIST 2 User manual

Type-A: plain type bolt
Type-B: with Spring Washer
1
2
3
4
Fig. A
Fig. B
Fig.C
Fig. D
P-600AL "Closet Cyclist 2" instructions manual
Upper Hook
Main Pillar
Lower Hook
Reinforcement Bar
Rear Leg
Right Side Front Leg Height Adjuster
Leg Base Plate
Stainless Band Clip
Thank you for purchasing Minoura "P-600AL Closet Cyclist 2" bicycle
display stand. This stand can hold up to two bikes in a narrow space
vertically in order to save your storage space as much as possible.
Please read this instructions manual to assemble and use the stand correctly
and safely.
Required Tools for Assembling
Bolt Type Variation
Install both side Front Legs to the
Leg Base Plate with supplied M6x35
type-A bolt, Flat washer, Collar and
M6 Nylon nut. (see Fig. A)
The Legs are different for right
side and left side.
Each Reinforcement Bar must be
inward.
M6 Nylon Nut
Collar
Flat Washer
Left Side
Front Leg
Place the Rear Leg on the Leg
Base Plate, and apply the Pillar
Base Plate onto the assembled legs.
Put the M6x40 type-A bolt with
Spring and Flat washer into the
front side hole and tighten them
temporarily. (see Fig. B)
Pillar Base
Plate
M6x40 Bolt
Rear Leg
Put the M6x40 type-A
bolt with Spring and Flat
washer into the backside
hole and tighten rmly.
After that, tighten the front
side bolt rmly too.
(see Fig. C)
M6x40 Bolt
Insert the Main Pillar onto the
Pillar Base Plate.
Apply the Backside Leg on the
back of the Main Pillar, then
tighten with the supplied two
M6x18 type-B bolts temporarily
(not rmly). (see Fig. D) Backside Leg
M6x18 Bolt
Main Pillar
1 x 5mm Hex Wrench
1 x 13mm Open Wrench
M6x35 Bolt
Leg Base Plate
MADE IN JAPAN

5
Fig.E
6
Fig.F
Fig.G
7
Fig.H
M6x70 Bolt
Install the Reinforcement Bars to the Main Pillar with supplied
M6x70 type-A bolt, Plastic washer, M6 at washer and M6
Nylon nut.
Then tighten the M6x18 bolts on the Backside Leg rmly.
(see Fig. E)
Plastic Washer
Reinforcement Bar
Longer Side
Shorter Side
Rectangle Nut
Stainless Band
Assembled
Stainless Band
Plastic Bracket
Once disassemble the Stainless Band Clip.
Wind the Stainless Band around the Main Pillar, insert the tip
between the Rectangle Nut and the box part of the band, and
apply the Plastic Bracket.
Attach the Upper Hook or Lower Hook onto the Plastic Bracket,
then tighten the bolt securely. (see Fig. F & G)
Upper Hook Lower Hook
P-600 is a tall stand, so you must maintain the balance whenever you
use it to prevent from any accident.
Adjust the Height Adjuster on each legs to keep the Main Pillar
vertically, then tighten the Lock Nut rmly with 13mm open wrench.
(see Fig. H)
< Complete Style with Bikes >
For More Information
MINOURA JAPAN HEAD OFFICE
1197-1 Godo, Anpachi, Gifu 503-2305 Japan
Fax [phone] / Email [email protected]
http://www.minoura.jp
MINOURA NORTH AMERICA
(for North American residents only)
1996 East Avenue, Hayward, CA 94541 U.S.A.
Fax [phone] / Email [email protected]