Trane Mitsubishi Electric TPEFYP006MA143A User manual

ii
HWE1832A GB
Safety Precautions
Read before installation and performing electrical work
Symbol explanations
Thoroughly read the following safety precautions prior to installation.
Observe these safety precautions for your safety.
This equipment may have adverse effects on the equipment on the same power supply system.
Contact the local power authority before connecting to the system.
WARNING
This symbol indicates that failure to follow the instructions exactly as stated poses the risk of serious injury or death.
CAUTION
This symbol indicates that failure to follow the instructions exactly as stated poses the risk of serious injury or dam-
age to the unit.
Indicates an action that must be avoided.
Indicates important instructions.
Indicates a parts that requires grounding.
Indicates that caution must be taken with rotating parts. (This symbol is on the main unit label.) <Color: Yellow>
Indicates that the parts that are marked with this symbol pose a risk of electric shock. (This symbol is on the main
unit label.) <Color: Yellow>
WARNING
Carefully read the labels affixed to the main unit.
WARNING
Do not use refrigerant other than the type indicated in the
manuals provided with the unit and on the nameplate.
Doing so may cause the unit or pipes to burst, or result in
explosion or fire during use, during repair, or at the time of
disposal of the unit.
It may also be in violation of applicable laws.
Mitsubishi Electric Trane HVAC US LLC cannot be held re-
sponsible for malfunctions or accidents resulting from the
use of the wrong type of refrigerant.
Ask your dealer or a qualified technician to install the unit.
Improper installation by the user may result in water leak-
age, electric shock, or fire.
Properly install the unit on a surface that can withstand its
weight.
Unit installed on an unstable surface may fall and cause in-
jury.
Only use specified cables. Securely connect each cable so
that the terminals do not carry the weight of the cable.
Improperly connected cables may produce heat and start a
fire.
Take appropriate safety measures against wind gusts and
earthquakes to prevent the unit from toppling over.
Improper installation may cause the unit to topple over and
cause injury or damage to the unit.
Only use accessories (i.e., air cleaners, humidifiers, electric
heaters) recommended by Mitsubishi Electric Trane HVAC
US LLC.
Do not make any modifications or alterations to the unit.
Consult your dealer for repair.
Improper repair may result in water leakage, electric shock,
or fire.
Do not touch the heat exchanger fins with bare hands.
The fins are sharp and pose a risk of cuts.
In the event of a refrigerant leak, thoroughly ventilate the
room.
If gaseous refrigerant leaks out and comes in contact with
an open flame, toxic gases will be generated.
Properly install the unit according to the instructions in the
Installation Manual.
Improper installation may result in water leakage, electric
shock, or fire.

ii
HWE1832A GB
Have all electrical work performed by an authorized electri-
cian according to the local regulations and the instructions
in this manual. Use a dedicated circuit.
Insufficient power supply capacity or improper installation
of the unit may result in malfunctions of the unit, electric
shock, or fire.
Keep electrical parts away from water.
Wet electrical parts pose a risk of electric shock, smoke, or
fire.
Securely attach the control box cover.
If the cover is not installed properly, dust or water may infil-
trate and pose a risk of electric shock, smoke, or fire.
Only use the type of refrigerant that is indicated on the unit
when installing or relocating the unit.
Infiltration of any other types of refrigerant or air into the unit
may adversely affect the refrigerant cycle and may cause
the pipes to burst or explode.
When installing the unit in a small space, take appropriate
precautions to prevent leaked refrigerant from reaching the
limiting concentration.
Leaked refrigerant gas will displace oxygen and may cause
oxygen starvation. Consult your dealer before installing the
unit.
Consult your dealer or a qualified technician when moving
or reinstalling the unit.
Improper installation may result in water leakage, electric
shock, or fire.
After completing the service work, check for a refrigerant
leak.
If leaked refrigerant is exposed to a heat source, such as a
fan heater, stove, or electric grill, toxic gases will be gener-
ated.
Do not try to defeat the safety features of the unit.
Forced operation of the pressure switch or the temperature
switch by defeating the safety features for these devices, or
the use of accessories other than the ones that are recom-
mended by Mitsubishi Electric Trane HVAC US LLC may
result in smoke, fire, or explosion.
Consult your dealer for proper disposal method.
Do not use a leak detection additive.

iiiiii
HWE1832A GB
Precautions for handling units for use with R410A
CAUTION
Do not use the existing refrigerant piping.
A large amount of chlorine that may be contained in the re-
sidual refrigerant and refrigerator oil in the existing piping
may cause the refrigerator oil in the new unit to deteriorate.
Use refrigerant piping materials made of phosphorus deox-
idized copper. Keep the inner and outer surfaces of the
pipes clean and free of such contaminants as sulfur, oxides,
dust, dirt, shaving particles, oil, and moisture.
Contaminants in the refrigerant piping may cause the refrig-
erator oil to deteriorate.
Store the piping materials indoors, and keep both ends of
the pipes sealed until immediately before brazing. (Keep el-
bows and other joints wrapped in plastic.)
Infiltration of dust, dirt, or water into the refrigerant system
may cause the refrigerator oil to deteriorate or cause the
compressor to malfunction.
Use a small amount of ester oil, ether oil, or alkyl benzene
to coat flares and flanges.
Infiltration of a large amount of mineral oil may cause the re-
frigerator oil to deteriorate.
Charge the system with refrigerant in the liquid phase.
If gaseous refrigerant is drawn out of the cylinder first, the
composition of the remaining refrigerant in the cylinder will
change and become unsuitable for use.
Only use R410A.
The use of other types of refrigerant that contain chloride
may cause the refrigerator oil to deteriorate.
Use a vacuum pump with a check valve.
If a vacuum pump that is not equipped with a check valve is
used, the vacuum pump oil may flow into the refrigerant cy-
cle and cause the refrigerator oil to deteriorate.
Prepare tools for exclusive use with R 410A. Do not use the
following tools if they have been used with the conventional
refrigerant: gauge manifold, charging hose, gas leak detec-
tor, check valve, refrigerant charge base, vacuum gauge,
and refrigerant recovery equipment.
If the refrigerant or the refrigerator oil that may be left on these
tools are mixed in with R410A, it may cause the refrigerator oil
in the new system to deteriorate.
Infiltration of water may cause the refrigerator oil to deteriorate.
Leak detectors for conventional refrigerants will not detect an
R410A leak because R410A is free of chlorine.
Do not use a charging cylinder.
If a charging cylinder is used, the composition of the refrigerant
in the cylinder will change and become unsuitable for use.
Exercise special care when handling tools for use with R410A.
Infiltration of dust, dirt, or water into the refrigerant system
may cause the refrigerator oil to deteriorate.

iv
HWE1832A GB

CONTENTS
HWE1832A GB
I Features
[1] Features.................................................................................................................................... 1
II Components and Functions
[1] Components and Functions...................................................................................................... 2
III Specifications
[1] Specifications............................................................................................................................ 5
1.Specifications.......................................................................................................................... 5
2.Electrical component specifications........................................................................................ 8
IV Outlines and Dimensions
[1] Outlines and Dimensions.......................................................................................................... 9
V Wiring Diagram
[1] Wiring Diagram ....................................................................................................................... 11
VI Refrigerant System Diagram
[1] Refrigerant system diagram.................................................................................................... 12
VII Microprocessor Control
[1] Microprocessor Control........................................................................................................... 13
1.Cool operation ...................................................................................................................... 13
2.Drying operation ................................................................................................................... 14
3.Fan operation........................................................................................................................ 15
4.Heat operation ...................................................................................................................... 16
5.Auto operation [Automatic cool / heat change over operation]............................................. 17
6.When unit is stopped control mode ...................................................................................... 18
7.Heater control ....................................................................................................................... 18
VIII Troubleshooting
[1] Troubleshooting ...................................................................................................................... 22
1.Check methods..................................................................................................................... 22
2.DC fan motor (fan motor/indoor control board)..................................................................... 26
3.Address switch setting .......................................................................................................... 27
4.Voltage test points on the control board ............................................................................... 28
5.Dipswitch setting (Factory setting)........................................................................................ 29
IX Disassembly Procedure
[1] Disassembly Procedure.......................................................................................................... 32
1.Control box ........................................................................................................................... 32
2.Thermistor (Intake air) .......................................................................................................... 33
3.Drainpan ............................................................................................................................... 34
4.Thermistor (Gas pipe) (Liquid pipe) ...................................................................................... 35
5.Fan and fan motor ................................................................................................................ 36
6.Heat exchanger .................................................................................................................... 37

HWE1832A GB

[ I Features ]
- 1 -
HWE1832A GB
I Features
[1] Features
Model Cooling capacity/Heating capacity
BTU/h kW
TPEFYP006MA143A 6000/6700 1.8/2.0
TPEFYP008MA143A 8000/9000 2.3/2.6
TPEFYP012MA143A 12000/13500 3.5/4.0
TPEFYP015MA143A 15000/17000 4.4/5.0
TPEFYP018MA143A 18000/20000 5.3/5.9
TPEFYP024MA143A 24000/27000 7.0/7.9
TPEFYP027MA143A 27000/30000 7.9/8.8
TPEFYP030MA143A 30000/34000 8.8/10.0
TPEFYP036MA143A 36000/40000 10.6/11.7
TPEFYP048MA143A 48000/54000 14.1/15.8
TPEFYP054MA143A 54000/60000 15.8/17.6

[ II Components and Functions ]
- 2 -
HWE1832A GB
II Components and Functions
[1] Components and Functions
1. Indoor (Main) Unit
(1) In case of rear inlet (2) In case of bottom inlet
Air inlet
Air outlet
Air outlet
Air inlet

[ II Components and Functions ]
- 3 -
HWE1832A GB
2. Remote Controller
[TAR-40MAAU]
Once the operation mode is selected, the unit will remain in the selected mode until changed.
(1) Remote Controller Interface
Main display Main menu
⑦⑧⑨⑩ ⑦⑧⑨⑩
Menu screen
⑦⑧⑨⑩
Function buttons
⑥
①
②
③
④
⑤
⑦⑧⑨⑩
Function guide
①[ON/OFF] button
Press to turn ON/OFF the indoor unit.
②[SELECT/HOLD] button
Press to save the setting.
When the Main menu is displayed, pressing this button will enable/disable the
HOLD function.
③[RETURN] button
Press to return to the previous screen.
④[MENU] button
Press to bring up the Main menu.
⑤Backlit LCD
Operation settings will appear.
When the backlight is off, pressing any button turns the backlight on and it will
stay lit for a certain period of time depending on the screen.
When the backlight is off, pressing any button turns the backlight on
and does not perform its function. (except for the [ON/OFF] button)
⑥ON/OFF lamp
This lamp lights up in green while the unit is in operation. It blinks while the
remote controller is starting up or when there is an error.
The functions of the function buttons change depending on the screen.
Refer to the button function guide that appears at the bottom of the LCD for
the functions they serve on a given screen.
When the system is centrally controlled, the button function guide that
corresponds to the locked button will not appear.
⑦Function button [F1]
Main display: Press to change the operation mode.
Menu screen: The button function varies with the screen.
⑧Function button [F2]
Main display: Press to decrease temperature.
Main menu: Press to move the cursor left.
Menu screen: The button function varies with the screen.
⑨Function button [F3]
Main display: Press to increase temperature.
Main menu: Press to move the cursor right.
Menu screen: The button function varies with the screen.
⑩Function button [F4]
Main display: Press to change the fan speed.
Menu screen: The button function varies with the screen.