Trane 4WCC4036E1000B User manual

SSAAFFEETTYY WWAARRNNIINNGG
Only qualified personnel should install and service the equipment The installation, starting up, and servicing of heating, ventilating, and air-conditioning
equipment can be hazardous and requires specific knowledge and training Improperly installed, adjusted or altered equipment by an unqualified person
could result in death or serious injury When working on the equipment, observe all precautions in the literature and on the tags, stickers, and labels that
are attached to the equipment
May 2023 1188--BBBB4411DD11--11CC--EENN
Single Packaged Heat Pump
13.4 SEER2 Convertible, 2 – 5 on
4WCC4024E1000A
4WCC4030E1000A
4WCC4036E1000B
4WCC4042E1000A
4WCC4048E1000A
4WCC4060E1000A
NNoottee:: “Graphics in this document are for representation
only. Actual model may differ in appearance.”
NNoottee:: “Unit specific Service Facts available online.”
Installation and Operations Manual

©2023 18-BB41D1-1C-EN
SAFE Y SEC ION
IImmppoorrttaanntt — This document contains a wiring
diagram, a parts list, and service information This is
customer property and is to remain with this unit
Please return to service information pack upon
completion of work
WWAARRNNIINNGG
HHAAZZAARRDDOOUUSS VVOOLLTTAAGGEE!!
FFaaiilluurree ttoo ffoollllooww tthhiiss WWaarrnniinngg ccoouulldd rreessuulltt iinn
pprrooppeerrttyy ddaammaaggee,, sseevveerree ppeerrssoonnaall iinnjjuurryy,, oorr
ddeeaatthh
DDiissccoonnnneecctt aallll eelleeccttrriicc ppoowweerr,, iinncclluuddiinngg rreemmoottee
ddiissccoonnnneeccttss bbeeffoorree sseerrvviicciinngg FFoollllooww pprrooppeerr
lloocckkoouutt//ttaaggoouutt pprroocceedduurreess ttoo eennssuurree tthhee ppoowweerr
ccaannnnoott bbee iinnaaddvveerrtteennttllyy eenneerrggiizzeedd
WWAARRNNIINNGG
SSAAFFEETTYY AANNDD EELLEECCTTRRIICCAALL HHAAZZAARRDD!!
FFaaiilluurree ttoo ffoollllooww tthhiiss WWaarrnniinngg ccoouulldd rreessuulltt iinn
pprrooppeerrttyy ddaammaaggee,, sseevveerree ppeerrssoonnaall iinnjjuurryy,, oorr
ddeeaatthh
TThheessee sseerrvviicciinngg iinnssttrruuccttiioonnss aarree ffoorr uussee bbyy
qquuaalliiffiieedd ppeerrssoonnnneell oonnllyy TToo rreedduuccee tthhee rriisskk ooff
eelleeccttrriiccaall sshhoocckk,, ddoo nnoott ppeerrffoorrmm aannyy sseerrvviicciinngg
ootthheerr tthhaann tthhaatt ccoonnttaaiinneedd iinn tthheessee ooppeerraattiinngg
iinnssttrruuccttiioonnss uunnlleessss yyoouu aarree qquuaalliiffiieedd ttoo ddoo ssoo
CCAAUUTTIIOONN
GGRROOUUNNDDIINNGG RREEQQUUIIRREEDD!!
FFaaiilluurree ttoo iinnssppeecctt oorr uussee pprrooppeerr sseerrvviiccee ttoooollss mmaayy
rreessuulltt iinn eeqquuiippmmeenntt ddaammaaggee oorr ppeerrssoonnaall iinnjjuurryy
RReeccoonnnneecctt aallll ggrroouunnddiinngg ddeevviicceess AAllll ppaarrttss ooff tthhiiss
pprroodduucctt tthhaatt aarree ccaappaabbllee ooff ccoonndduuccttiinngg eelleeccttrriiccaall
ccuurrrreenntt aarree ggrroouunnddeedd IIff ggrroouunnddiinngg wwiirreess,, ssccrreewwss,,
ssttrraappss,, cclliippss,, nnuuttss,, oorr wwaasshheerrss uusseedd ttoo ccoommpplleettee aa
ppaatthh ttoo ggrroouunndd aarree rreemmoovveedd ffoorr sseerrvviiccee,, tthheeyy mmuusstt
bbee rreettuurrnneedd ttoo tthheeiirr oorriiggiinnaall ppoossiittiioonn aanndd pprrooppeerrllyy
ffaasstteenneedd
WWAARRNNIINNGG
UUNNIITT CCOONNTTAAIINNSS RR--441100AA
RREEFFRRIIGGEERRAANNTT!!
FFaaiilluurree ttoo uussee pprrooppeerr sseerrvviiccee ttoooollss mmaayy rreessuulltt iinn
eeqquuiippmmeenntt ddaammaaggee oorr ppeerrssoonnaall iinnjjuurryy
RR--441100AA ooppeerraattiinngg pprreessssuurree eexxcceeeeddss tthhee lliimmiitt ooff RR--
2222 PPrrooppeerr sseerrvviiccee eeqquuiippmmeenntt iiss rreeqquuiirreedd SSeerrvviiccee
uussiinngg oonnllyy RR--441100AA RReeffrriiggeerraanntt aanndd aapppprroovveedd PPOOEE
ccoommpprreessssoorr ooiill
WWAARRNNIINNGG
SSAAFFEETTYY HHAAZZAARRDD!!
OOppeerraattiinngg tthhee uunniitt wwiitthhoouutt tthhee aacccceessss ppaanneellss
pprrooppeerrllyy iinnssttaalllleedd mmaayy rreessuulltt iinn sseevveerree ppeerrssoonnaall
iinnjjuurryy oorr ddeeaatthh
DDoo nnoott ooppeerraattee tthhee uunniitt wwiitthhoouutt tthhee eevvaappoorraattoorr ffaann
aacccceessss ppaanneell oorr eevvaappoorraattoorr ccooiill aacccceessss ppaanneell iinn
ppllaaccee
WWAARRNNIINNGG
WWAARRNNIINNGG!!
TThhiiss pprroodduucctt ccaann eexxppoossee yyoouu ttoo cchheemmiiccaallss
iinncclluuddiinngg lleeaadd,, wwhhiicchh aarree kknnoowwnn ttoo tthhee SSttaattee ooff
CCaalliiffoorrnniiaa ttoo ccaauussee ccaanncceerr aanndd bbiirrtthh ddeeffeeccttss oorr
ootthheerr rreepprroodduuccttiivvee hhaarrmm FFoorr mmoorree iinnffoorrmmaattiioonn ggoo
ttoo wwwwww PP6655WWaarrnniinnggss ccaa ggoovv
IImmppoorrttaanntt:: Wear appropriate loves, arm sleeve
protectors and eye protection when
servicin or maintainin this equipment.
IImmppoorrttaanntt:: Air filters and media wheels or plates shall
meet the test requirements in UL 900.

18-BB41D1-1C-EN 3
Introduction, Unit Inspection and
Specification 4
Introduction 4
Inspect Shipment 4
Product Specification 5
Charging in Cooling above 55°F OD
Ambient 6
Determine Unit Clearances 7
Review Location and Recommendation
Information 9
Unit Installation 10
Ground Level Installation 10
Rooftop Installation — Curb
Mounting 10
Lifting and Rigging 11
Rooftop Installation — Frame
Mounting 12
Rooftop Installation — No Curb/
Frame 12
Ductwork Installation 15
Attaching Downflow Ductwork to
Roof Curb 15
Attaching Downflow Ductwork to Roof
Frame 15
Attaching Horizontal Ductwork to
Unit 15
Condensate Drain Piping 15
Air Filter Installation 15
Electrical Wiring 16
Unit Startup 18
Pre-Start Quick Checklist 18
Starting the Unit in Cooling Mode 18
Starting the Unit in Heating Mode 18
Sequence of Operation 19
Final Installation Checklist 20
Maintenance 20
Owner Maintenance 20
Service Maintenance 20
Defrost Control 21
Pressure Curves 24
Indoor Fan Performance 30
Refrigerant Circuit 32
Troubleshooting Chart 33
able of Contents
Important Product Information 36

418-BB41D1-1C-EN
Introduction, Unit Inspection and Specification
Introduction
Read this manual carefully before attempting to install,
operate, or perform maintenance on this unit
Installation and maintenance should be performed by
qualified service technicians only This unit is listed by
Underwriters Laboratory
Packaged units are designed for outdoor mounting
with a vertical condenser discharge They can be
located either at ground level or on a roof in
accordance with local codes Each unit contains an
operating charge of refrigerant as shipped
Extreme mounting kits are available for slab
(BAYEXMK003A), utility curb (BAYEXMK002B) and
perimeter curb (BAYEXMK001A) mountings
Inspect Shipment
1 Check for damage after the unit is unloaded Report
promptly to the carrier any damage found to the
unit Do not drop the unit
IImmppoorrttaanntt:: To prevent dama e to the sides and top of
the unit when hoistin , use “spreader
bars” see, “Rooftop Installation — No Curb/
Frame,” p. 12.
2 Check the unit’s nameplate to determine if the unit
is correct for the intended application The power
supply must be adequate for both the unit and all
accessories
3 Check to be sure the refrigerant charge has been
retained during shipment Remove the Compressor
access panel to access the 1/4" flare pressure taps
4 If this unit is being installed on a curb, verify that
the correct curb is provided with the unit
• 4WCC4024–036 use model BAYCURB050A,
• 4WCC4042–060 use model BAYCURB051A
5 If the unit is being hoisted, accessory kit
BAYLIFT002A is recommended It includes a kit of
four (4) lifting lugs and instructions
NNootteess::
• If practical, install any internal accessories
to the unit at the shop.
• The packa ed units have been evaluated
in accordance with the Code of Federal
Re ulations, Chapter XX, Part 3280 or the
equivalent. “SUITABLE FOR MOBILE
HOME USE.”

18-BB41D1-1C-EN 5
Product Specification
MODEL 4WCC4024 4WCC4030 4WCC4036 4WCC4042 4WCC4048 4WCC4060
RATED Volts/PH/Hz 208–230/1/60
Performance Cooling BTUH(a) 23800 29800 35200 43000 47000 57000
Indoor Airflow (CFM) 770 985 1105 1355 1590 1835
Power Input (KW) 2.09 2.55 3.03 3.54 4.10 4.85
EER2/SEER2 (BTU/Watt-Hr.)(b) 11.0 / 13.4
Sound Power Rating [dB(A)](c) 66.4 70.0 69.4 71.5 72.5 77.3
PERFORMANCE HEATING 208–230/1/60
(High Temp.) BTUH 23200 28600 34400 39000 45000 55000
Power Input (KW) 1.95 2.31 2.93 3.43 3.94 4.71
(Low Temp.) BTUH 14700 17200 22000 23400 26200 35400
Power Input (KW) 1.78 2.16 2.76 3.15 3.61 4.34
HSPF2 (BTUH/Watt-Hr) 7.0
POWER CONN. — V/Ph/Hz 208–230/1/60
Min. Brch. Cir. Ampacity(d) LOCATED ON UNIT NAMEPLATE
Fuse Size — Max. (amps) LOCATED ON UNIT NAMEPLATE
Fuse Size — Recmd. (amps) LOCATED ON UNIT NAMEPLATE
COMPRESSOR SCROLL
VOLTS/PH/HZ 208–230/1/60
R.L. Amps — L.R. Amps LOCATED ON UNIT NAMEPLATE
OUTDOOR COIL — TYPE SPINE FIN
Rows/F.P.I 2 / 24
Face Area (sq. ft.) 13.32 13.32 15.49 20.54 20.54 22.90
Tube Size (in.) 3/8
Refrigerant Control EXPANSION VALVE
INDOOR COIL — TYPE PLATE FIN
Rows/F.P.I 3 / 15 3/15 4/15 4/15 3/15 3/15 4/15
Face Area (sq. ft.) 3.5 5.0
Tube Size (in.) 3/8
Refrigeration Control EXPANSION VALVE
Drain Conn. Size (in.) 3/4" FEMALE NPT
OUTDOOR FAN — TYPE SWEPT
DIA. (IN.) 23.4 28.3
DRIVE/NO. SPEEDS DIRECT / 1
CFM @ 0.0 in. w.g.(e) 2550 3270 3250 4400 4400 5500
Motor — HP/R.P.M 1/12 /850 1/6/842 1/5/855 1/4/798 1/4 /825 1/3/825
Volts/Ph/Hz 208–230/1/60
F.L. Amps/L.R Amps LOCATED ON UNIT NAMEPLATE
INDOOR FAN — TYPE Constant Torque ECM
Dia. x Width (in.) 10.62 x 10.68 10.62 x 10.62 11.87 x 10.68
Drive/No. Speeds DIRECT / 4
CFM @ 0.0 in. w.g.(f) SEE FAN PERFORMANCE TABLE
Motor — HP / R.P.M. 1/2/1050 1/2/1050 1/2/1050 3/4/1050 3/4/1050 1/1050
Volts/Ph/Hz 208–230/1/60
F.L. Amps LOCATED ON UNIT NAMEPLATE
FILTER / FURNISHED NO
Type Recommended THROWAWAY
Recmd. Face Area (sq. ft)(g) 2.7 4 5.3
REFRIGERANT R-410A
Charge (lbs.) LOCATED ON UNIT NAMEPLATE
Subcooling 16° 14° 11° 9° 8° 6°
(a) Rated in accordance with AHRI Standard 210/240.
(b) Rated in accordance with D.O.E. test procedure.
(c) Sound Power values are not adjusted for AHRI 270–95 tonal corrections.
(d) Calculated in accordance with currently prevailing Nat’l Electrical Code.
(e) Standard Air — Dry Coil — Outdoor.
(f) Standard Air — Dry Coil — Indoor
(g) Filters must be installed in return air stream. Square footages listed are based on 300 f.p.m. face velocity. If permanent filters are used size per
manufacturer’s recommendation with a clean resistance of 0.05” W.C.
IInnttrroodduuccttiioonn,, UUnniitt IInnssppeeccttiioonn aanndd SSppeecciiffiiccaattiioonn

618-BB41D1-1C-EN
Charging in Cooling above
55°F OD Ambient
If servicing the equipment requires system evacuation,
then re-charge the system to the weight specified on
the nameplate Verify the system subcooling using the
Subcooling Charging Table and, if necessary, adjust
the charge using the procedure below
1 For best results — the indoor temperature should
be kept between 70°F to 80°F Add system heat if
needed
2 Whenever charge is removed or added, the system
must be operated for a minimum of 20 minutes to
stabilize before accurate measurements can be
made
3 Measure Liquid Line Temperature and Refrigerant
Pressure at service valved in the compressor
compartment
4 Locate your liquid line temperature in the left
column of the table, and the intersecting liquid line
pressure under the subcool value column, Add
refrigerant to raise the pressure to match the table,
or remove refrigerant to lower the pressure Again,
wait 20 minutes for the system conditions to
stabilize before adjusting charge again
NNoottee:: System char e shall never be more than 110% or
less than 90% of nameplate char e. If specified
subcoolin cannot be achieved within those
char e bounds, contact your Field Service
Representative.
5 When system is correctly charged, you can refer to
System Pressure Curves to verify typical
performance
CCHHAARRGGIINNGG BBEELLOOWW 5555°°FF
Evacuate system and weigh in nameplate charge or
use factory charge Correct subcooling may be verified
when the temperature is above 55°F
R-410A REFRIGERANT CHARGING CHART
Refer to Service Facts or Installer’s Guide for charging method
LIQUID
TEMP
(°F)
DESIGN SUBCOOLING (°F)
6 8 9 10 11 12 13 14 16
LIQUID GAGE PRESSURE (PSI)
55 174 179 182 185 188 191 195 198 205
60 189 195 198 201 204 208 211 215 222
65 205 211 215 218 222 225 229 232 240
70 222 229 232 236 240 243 247 251 259
75 240 247 251 255 259 263 267 271 279
80 259 267 271 275 279 283 287 291 301
85 279 287 291 296 300 304 309 313 323
90 301 309 313 318 322 327 331 336 347
95 323 331 336 341 346 351 355 360 371
100 347 355 360 365 370 376 381 386 398
105 371 381 386 391 396 402 407 413 425
110 398 407 413 418 424 429 435 441 454
115 425 435 441 446 452 458 464 470 484
120 454 464 470 476 482 488 495 501 516
125 484 495 501 507 514 520 527 533 549
From Dwg. D154557P01
CChhaarrggiinngg BBeellooww 5555°FF OODD AAmmbbiieenntt iinn HHeeaattiinngg OOnnllyy
1 The Subcool Charging Method in cooling is NOT
recommended below 55°F outdoor ambient
2 The only recommended method of charging at
outdoor ambients below 55°F, is to weigh in the
charge in the heating mode
3 Use Nameplate charge
4 Check liquid line temperature and pressure (at the
OD valves) to obtain a minimum of the subcooling
shown in the subcooling table
5 Add charge if the minimum subcooling as shown in
the table is not obtained with the nameplate charge
6 It is important to return in the spring or summer to
accurately charge the system in the cooling mode
at outdoor ambients above 55°F
IInnttrroodduuccttiioonn,, UUnniitt IInnssppeeccttiioonn aanndd SSppeecciiffiiccaattiioonn

18-BB41D1-1C-EN 7
Determine Unit Clearances
Figure 1. Space on Sides Requirements
CC
DD
BB
FF
EE
W/ ECONOMIZER W/ ECONOMIZER
BACK SIDE 305 [12] 762 [30] 305 [12] 762 [30]
LEFT SIDE 762 [30] 914 [36] 914 [36] 1067 [42]
RIGHT SIDE 610 [24] - 610 [24] -
FRONT SIDE 1067 [42] - 762 [30] -
BOTTOM
BACK SIDE
LEFT SIDE
RIGHT SIDE
FRONT SIDE
TOP
A
BB
CC
DD -Depth
EE -Width
FF 497.8 [19-5/8] 576.00 [22-11/16]
CENTER OF GRAVITY - TABLE NEXT PAGE
CENTER OF GRAVITY - TABLE NEXT PAGE
1049.02 [41-5/16] 1125.22 [44-5/16]
1240.28 [48-27/32] 1487.17 [58-9/16]
305 [12] 305 [12]
914 [36] 914 [36]
DIMENSIONS mm [Inches]
HEIGHT OF UNIT - TABLE NEXT PAGE
25 [1] 25 [1]
152 [6] 152 [6]
152 [6] 152 [6]
2 - 3 TON Units 3.5 - 5 TON Units
RECOMMENDED SERVICE CLEARANCE mm [Inches]
CLEARANCE TO COMBUSTIBLE MATERIAL mm [Inches]
0 0

818-BB41D1-1C-EN
Figure 2. Bottom and Back Duct Openings
B
C
D
E
F
E
G
H
M
L
J
J
I
K
N
Height mm[in]
A -Height B C D E F G H I J K L M N
4WCC4024 898.53 [35.38]
4WCC4030
4WCC4036
4WCC4042
4WCC4048
4WCC4060 1050.93 [41.38]
177.55
[6.99]
296.62
[11.68]
304.80
[12]
75.41
[2.93]
75.41
[2.93]
406.40
[16]
167.89
[6.61]
173.46
[16]949.33 [37.38]
1000.13 [39.38] 457.20
[18]
75.41
[2.97]
75.41
[2.97]
PHYSICAL DIMENSIONS mm[In]
79.50
[3.13]
449.02
[17.68]
176.07
[6.93]
322.84
[12.71]
372.82
[14.68]
1155.45
[45.49]
1402.34
[55.21]
381.00
[15]
244.09
[9.61]
318.75
[12.55]
381.00
[15]
304.80
[6.8]
79.50
[3.13]
398.22
[15.68]
176.07
[6.93]
W1 W2 W3 W4 BB CC
4WCC4024 52.9 [117] 33.3 [73] 24.1 [53] 38.3 [84] 182.3 [402] 148.6 [328] 430 [16.9] 565.3 [22.3]
4WCC4030 55.3 [122] 50.3 [110] 16.6 [37] 39.2 [86] 195.0 [430] 161.3 [355] 413.5 [16.3] 581 [22.9]
4WCC4036 59.6 [131] 37.3 [82] 26.6 [59] 41.7 [92] 199 [439] 165.3 [364] 430 [16.9] 535 [21.1]
4WCC4042 64.4 [142] 47.6 [105] 39.5 [87] 49.9 [110] 248.6 [547.9] 201.4 [444] 449.6 [17.7] 641.8 [25.3]
4WCC4048 68.9 [152] 40.8 [90] 30.8 [68] 52.2 [115] 240 [529] 192.8 [425] 414.0 [16.3] 414.0 [16.3]
4WCC4060 79.4 [175] 47.2 [104] 35.8 [79] 59.9 [132] 269.5 [594] 222.3 [490] 414.0 [16.3] 414.0 [16.3]
Corner Weights KG/LBS SHIPPING WEIGHT
KG/LBS UNIT WEIGHT KG/LBS
Center Of Gravity mm[inch]
DDeetteerrmmiinnee UUnniitt CClleeaarraanncceess

18-BB41D1-1C-EN 9
Review Location and Recommendation Information
HHoorriizzoonnttaall AAiirrffllooww UUnniittss
1 Location of the unit must allow service clearance
around it to ensure adequate serviceability,
maximum capacity, and peak operating efficiency
2 These units are designed for outdoor installation
They may be installed directly on a slab, wood
flooring, or on Class A, B, or C roof covering
material The discharge air from the condenser fans
must be unrestricted for a minimum of 3 feet above
the unit
3 Check the handling facilities to ensure the safety of
personnel and the unit(s)
4 The unit must be mounted level for proper drainage
of water through the drain holes in the base pan
5 The unit should not be exposed to direct roof water
runoff
6 Flexible duct connectors must be of a flame
retardant material All duct work outside of the
structure must be insulated and weatherproofed in
accordance with local codes
7 Holes through exterior walls or roof must be sealed
in accordance with local codes
8 All fabricated outdoor ducts should be as short as
possible
CClleeaarraanncceess
1 The recommended clearances for single-unit
installations are illustrated in “Determine Unit
Clearances,” p 7
2 Any reduction of the unit clearances indicated in
these figures may result in condenser coil
starvation or the recirculation of warm condenser
air Actual clearances, which appear to be
inadequate should be reviewed with a local
engineer
3 See the unit’s nameplate for the absolute minimum
clearance between the unit and any combustible
surfaces
DDoowwnn AAiirrffllooww UUnniittss
1 Location of the unit must allow service clearance
around it to ensure adequate serviceability,
maximum capacity, and peak operating efficiency
2 Refer to the Installation section for instruction on
converting the supply and return airflow covers to
down airflow
3 The field assembled Roof Mounting Curb
(BAYCURB050A or BAYCURB051A) or a field
fabricated curb should be in place before the unit is
hoisted to the roof top
The Roof Mounting Curb (frame) must be installed
on a flat, level section of the roof (maximum of 1/4"
per foot pitch) and provide a level mounting surface
for the unit Also, be sure to provide sufficient
height above the roof to prevent water from
entering the unit
4 Be sure the mounting curb spans structural
members (trusses) of the roof, thereby providing
sufficient support for the weight of the unit, the
curb, the duct(s), and any factory or field installed
accessories
5 The unit must be mounted level for proper drainage
of water through the drain holes in the base pan
6 Be sure the hole in the structure for the ducts is
large enough to accommodate the fabricated ducts
and the insulation surrounding them Flexible duct
connectors must be of a flame retardant material
All duct work outside of the structure must be
insulated and weatherproofed in accordance with
local codes
7 Holes through exterior walls or roof must be sealed
in accordance with local codes
8 These units are design certified for outdoor
installation They may be installed directly on a
slab, wood flooring, or on Class A, B, or C roof
covering material The discharge air from the
condenser fans must be unrestricted for a minimum
of 3 feet above the unit
9 Check the handling facilities to ensure the safety of
personnel and the unit(s)
CClleeaarraanncceess
1 The recommended clearances for single-unit
installations are illustrated in “Determine Unit
Clearances,” p 7
2 Any reduction of the unit clearances indicated in
these figures may result in condenser coil
starvation or the recirculation of warm condenser
air Actual clearances, which appear to be
inadequate should be reviewed with a local
engineer
3 See the unit’s nameplate for the absolute minimum
clearance between the unit and any combustible
surfaces

10 18-BB41D1-1C-EN
Unit Installation
NNoottee:: The factory ships this unit for horizontal
installation.
Ground Level Installation
TToo IInnssttaallll tthhee uunniitt aatt ggrroouunndd lleevveell::
1 Place the unit on a pad the size of the unit or larger
The unit must be mounted level for proper drainage
of water through the holes in the base pan To
attach the unit securely to the slab, use extreme
mounting kit, BAYEXMK003A Usage of the
extreme mounting kit accessories is a
recommendation, not a requirement
The pad must not come in contact with the
structure Be sure the outdoor portion of the supply
and return air ducts are as short as possible As
indicated in Table 1, p 12, vibration support is a
recommendation, not a requirement
2 Location of the unit must allow service clearance
around it Clearance of the unit must be given
careful consideration See “Determine Unit
Clearances,” p 7
NNoottee:: Any reduction of the unit clearances indicated
in these illustrations may result in condenser
coil starvation or the recirculation of warm
condenser air. Actual clearances, which
appear to be inadequate should be reviewed
with a local en ineer.
IImmppoorrttaanntt:: A minimum 0" clearance to combustible
material shall be maintained on air
outlet duct.
3 Attach the supply and return air ducts to the unit as
explained in the ductwork Installation section
4 Flexible duct connectors must be of a flame
retardant material Insulate any ductwork outside of
the structure with at least two (2) inches of
insulation and weatherproof There must be a
weatherproof seal where the duct enters the
structure
5 Do not expose the unit to direct roof water runoff
6 Seal all holes through exterior walls in accordance
with local codes
7 Continue with the following installation sections to
complete the installation: Ductwork, Filter and
Electrical Wiring
Rooftop Installation — Curb
Mounting
CCoonnvveerrtt HHoorriizzoonnttaall AAiirrffllooww ttoo DDoowwnn AAiirrffllooww
The factory ships the unit for horizontal airflow
Perform this procedure to convert it to down airflow:
1 Remove the three (3) sheet metal screws securing
the supply air cover and the four (4) sheet metal
screws securing the return air cover from the base
of the unit Remove the covers from the base
2 Place the covers over the horizontal supply and
return openings (painted side out) Align the screw
holes, and secure using the same screws removed
in step 1
IInnssttaallll FFuullll PPeerriimmeetteerr RRooooff MMoouunnttiinngg CCuurrbb
1 Verify that the roof mounting curb is correct for the
unit There are two curbs depending on the unit
cabinet sizes:
• 4WCC4024–036 use model BAYCURB050A,
• 4WCC4042–060 use model BAYCURB051A
2 Assemble and install the curb following the
instructions in the Installer's Guide included with
the appropriate curb
Figure 3. ypical Ground Level Application
NNoottee:: Use the extreme mountin kit, BAYEXMK002AA, to secure the unit to the slab.
SIDING
RETURN
AIR DUCT
SUPPLY
AIR DUCT
EXTERIOR
WALL INSULATE
WEATHERPROOF
OR RAIN SHIELD FLEXIBLE DUCT
CONNECTORS
OUTDOOR
AIR DISCHARGE
SUPPORT PAD
FOUNDATION
3/4” VIBRATION ISOLATORS, USE
7 ISOLATORS