Trane 4950 0471 Instruction Manual

© 2008 Trane All rights reserved 3270 3319 Rev B
®
Installing and Configuring the BACnet
®
/IP Router
Ordering number: 4950 0471 (ARCNET), 4950 0472 (Ethernet)
This document describes the installation and
configuration of the BACnet/IP Router. The router
enables you to connect two BACnet local area
networks (LANs) to create a BACnet inter-network.
The LANs may be either BACnet/IP Ethernet or
BACnet ARCNET®.
Before you begin
Before wiring or configuring the router, get the
TCP/IP information from the network administrator
for the site. Figure 1 on page 2 shows a sample letter
of request. Ensure that the TCP/IP information
includes: IP address, subnet mask, default gateway,
and
user datagram protocol (UDP) port .
In addition to the TCP/IP information, you may also
need the following information to help with the
network system setup:
• Capability of enabling and disabling a BACnet
broadcast messaging device (BBMD)
• IP addresses of remote BBMDs, routers, and
gateways in the TCP/IP networks
• BACnet network numbers for each of the direct
LAN interfaces
• Information about the LAN to which the router
will be connected, such as other devices connected
to it: BACnet routers, BBMDs, TCP/IP routers,
gateways, switches, and hubs
Note:
Since the router holds configuration information
indefinitely, you can configure the router before
travelling to the site.
For more information about BACnet/IP network
installations, see engineering bulletin Tracer
Summit®BACnet/IP Network Installations (BAS-
PRB004-EN).
When you have the TCP/IP information, refer to the
topics that follow. The topics provide router
specifications and wiring information. They also
provide information and procedures for connecting,
configuring, and troubleshooting the router.
Router specifications
Table 1 shows the specifications for the Router.
Wire the router
When wiring the router and the hub to the Ethernet
LAN, use any combination of straight (patch) cables
and crossover category (CAT) 5 cables. Using CAT 5
cables enables you to connect other devices, such as
a BMTW building control unit (BCU) to the LAN.
Use straight cables when there is a hub; use
crossover cables when there is no hub.
Figure 2 on page 3 shows a router connected to a
typical LAN topology.
Note:
If you are using coax cable, prior to wiring the
router, verify that each LAN cable is terminated
with the appropriate resistor. Ethernet RG58 coax
cable needs a 50 ohm resistor. ARCNET RG62 coax
cable needs a 93 ohm resistor.
To wire the configuration shown in
Figure 2 on page 3:
1. Using straight CAT 5 cables, connect the
workstation to the Ethernet LAN and the
Ethernet LAN to the hub.
Table 1: Router specifications
Electrical
requirements
100 Vac at 50–60 Hz
(240 Vac at 50–60 Hz)
45 W
Operating
temperature
32–158° F
(0–70° C)
Dimensions 3 in. × 7.5 in. × 13 in.
(8 cm × 19 cm × 35 cm)
Weight 54 oz
(1.5 kg)
Mounting Screw slots for wall mounting
Optional rack mount ears

3270 3319 Rev B 2
Figure 1: Sample Planning Memo
Note:
If the router has two Ethernet cards, the ports
are labeled with the interface number for each
card (refer to factory configuration document).
2. Using a straight CAT 5 cable, connect the hub to
the bottom RJ-45 port on the router
(Figure 3 on page 3).
3. Using a crossover CAT 5 cable, connect the
10Base2 Ethernet port to the BMTS BCU
Ethernet port.
Note:
The router cannot start without the onboard
Ethernet connected.
4. Connect the supplied ac power cable to both the
router and an ac power source.
Note:
There is no power switch. When the router is
connected to both an IP Ethernet LAN and a
power source, the router turns on.
▲ IMPORTANT
Do not plug an active ARCNET cable into the
onboard Ethernet port. Electrical incompatibilities
between the two network types may cause the
Ethernet port to be permanently damaged.
Note:
If an ARCNET cable is disconnected during
router operation, the router buffers the packets
that are destined for the ARCNET network as
long as possible. When all buffers are full, the
router automatically reboots.
To: Owner’s IS Staff
From: Local Trane Office
Date: June 7, 2000
Subject: Tracer Summit System Installation
As part of the upcoming facility renovation project, Trane has been
selected to provide the new facility-wide Building Automation System. This
system will control heating, air conditioning, and ventilation in the facility to
provide increased comfort and decreased utility costs. The Trane system
selected is called Tracer Summit.
The Tracer Summit system consists of a series of embedded controllers,
called Building Control Units (BCUs), and PC Workstations. The BCUs
control the equipment in the facility, and the PC Workstations are used for
system configuration and operation. As part of the construction
specifications, Trane is required to use the TCP/IP network for
communications.
Tracer Summit communications use the BACnet protocol (ASHRAE/ANSI
135-95), and IP communications follow annex J-1999 of this standard.
The critical networking requirements are:
•IP communications using UDP at port 47808 or other user-designated
port.
•Each BCU must have a permanently assigned IP address, subnet
mask, and gateway address.
•PC Workstations can have a permanently assigned IP address or use
DHCP.
•If you choose to allow access from the Internet, the firewall must allow
UDP at the designated port and expose the IP addresses of the BCUs
(i.e. NAT not enabled on these devices).
•Dialup communications supported either via IP Dialup (PPP) to your
intranet (provided by others), or directly to any BCU using Tracer
Summit workstation software.
This allows for easy operation on your corporate intranet. Any point of
access to the intranet can be used to connect to the Tracer Summit
system.
For installation of the Tracer Summit system, we need network jacks
(10BaseT) in the Mechanical rooms in the Northeast corner of the first
through fourth floors of your facility. We also need the following
information for each Mechanical room:
Location IP
Address
Subnet
Mask
Gateway
Floor 1
Floor 2
Floor 3
Floor 4
UDP port: __________
We will also be installing the Tracer Summit Windows 95/98/2000/NT 4.0-
compatible software on the PC workstation located on the Facility
Manager’s desk. This PC will need to be set up for IP communications by
your staff, using either a permanently assigned IP address or DHCP.
When you have the above information, please send it to me at EMAIL
ADDRESS, or fax this page to me at FAX NUMBER. If you have any
questions or concerns, please call me at [phone].
I am looking forward to working with you on this project.
Thanks again,
Project Manager

3 3270 3319 Rev B
Figure 2: Sample router network
Figure 3: Router ports
Connect PC to router
The router is a single-board computer. It has no
keyboard or display. To interface with the router and
configure it, connect the router to a PC that has a
terminal emulation program such as ProComm™ or
HyperTerminal.
Prior to connecting to the router via terminal
emulation, ensure that the PC satisfies these
requirements:
• Serial port cabled to the router console port
(Figure 3) with the provided crossover cable
• Properties set to: 9600 baud, 8 bits, 1 stop bit, and
no parity
• ANSI command and character sets installed
(VT100 compatible)
Tracer Summit
PC Workstation (v10.0)
BACnet Ethernet or ARCNET LAN
BMTW BCU
IP: 192.168.0.23
Subnet mask: 255.255.255.0
Gateway: 192.168.0.55
BMTS BCU
Tracer Summit PC Workstation (v11.0)
IP: 192.168.0.20
Subnet mask: 255.255.255.0
Gateway: 192.168.0.55
Router
IP: 192.168.0.22
Network: 192.168.0.0
Network mask: 255.255.255.0
Broadcast: 192.168.0.255
Default gateway: 192.168.0.55
Hub
RJ-45 port Console port
10Base2 Ethernet port
Ethernet 1 or ARCNET 1
connected to BACnet
Ethernet 0
connected to IP

3270 3319 Rev B 4
To connect to the router via terminal emulation:
1. At the login prompt, type:
root
2. Press ENTER.
3. At the password prompt, type:
1q2w3e4r
4. Press ENTER.The setup menu displays
(Figure 4).
5. Go to Configure router.
Configure router
After connecting to the router via terminal
emulation, you must configure the router.
Configuring the router begins at the setup menu.
The setup menu enables you to set, change, and save
TCP/IP information in a file on the router flash disk.
Note:
If the setup menu is not displayed on the PC screen,
use the RCONFIG editing program to access it. At
the command line, type RCONFIG, then press
ENTER until the setup menu displays (Figure 4).
View the PORT TABLE screen and note LANs setup:
1. At the setup menu (Figure 4), use the TAB key to
move the cursor to Port Table.
2. Press ENTER. The PORT TABLE screen displays
(Figure 5).
Note:
The bottom of the PORT TABLE screen shows
the navigation commands. The most commonly
used commands are TAB, +, and ^Q(CTRL key
and Qkey pressed simultaneously). The ^Q
(return) command steps the display back
through the program.
3. At the BACnet Network column, verify that each
BACnet LAN has a network number from 1
through 65,534 (FFFE hex).
Note:
The network number is the same as the BCU
network number in the site configuration
information.
4. At the NIC and BACnet Protocol columns, verify
eth0 is a BACnet/IP LAN, eth1 is an Ethernet
LAN, and arc0 is an ARCNET LAN.
Note:
The router supports one eth0 connection and
either one eth1 or one arc0 connection
(Figure 3 on page 3).
5. Use the ^Qcommand to return to the setup
menu (Figure 4).
6. Go to Configure eth0 from the NETWORK
CONFIGURATION screen on page 5.
Figure 4: Setup menu
Figure 5: Sample PORT TABLE screen

5 3270 3319 Rev B
Configure eth0 from the NETWORK
CONFIGURATION screen
Configure the Ethernet 0 (eth0) network interface
card (NIC) at the NETWORK CONFIGURATION
screen:
1. At the setup menu (Figure 4 on page 4), use the
TAB key to move the cursor to Network
Configuration.
2. Press ENTER. The NETWORK
CONFIGURATION screen displays (Figure 6).
Note:
The bottom of the NETWORK
CONFIGURATION screen shows the navigation
commands. The most commonly used commands
are TAB, +, and ^Q(CTRL key and Qkey pressed
simultaneously). The ^Q(return) command
steps the display back through the program.
3. Use the TAB key to move the cursor to eth0.
4. Use the TAB key to move the cursor to the IP
Address field in the IP Configuration column.
5. Type the IP address that you received from the
network administrator.
6. Press the TAB key to move the cursor to the
Network field in the IP Configuration column.
7. Type the same address that you entered in the
IP Address field, but substitute a 0for the last
number.
8. Press the TAB key to move the cursor to the
Network Mask field in the IP Configuration
column.
9. Type the subnet mask address that you received
from the network administrator.
10. Press the TAB key to move the cursor to the
Broadcast field in the IP Configuration column.
11. Type the same address that you entered in the
IP Address field, but substitute 255 for the last
number.
12. Use the ^Qcommand to return to the setup
menu (Figure 4 on page 4).
13. Go to Configure eth1 from the NETWORK
CONFIGURATION screen on page 6.
Figure 6: Sample NETWORK CONFIGURATION screen for eth0

3270 3319 Rev B 6
Configure eth1 from the NETWORK
CONFIGURATION screen
The configuration of NIC Ethernet 1 (eth1) applies
to the router. Normally, eth1 is preconfigured, but if
you have to configure it, use the following procedure.
At most, you should only have to configure eth1
once. Configure eth1 at the NETWORK
CONFIGURATION screen:
1. At the setup menu (Figure 4 on page 4), use the
TAB key to move the cursor to Network
Configuration.
2. Press ENTER. The NETWORK
CONFIGURATION screen displays (Figure 7).
Note:
The bottom of the NETWORK
CONFIGURATION screen shows the navigation
commands. The most commonly used commands
are TAB, +, and ^Q(CTRL key and Qkey pressed
simultaneously). The ^Q(return) command
steps the display back through the program.
3. Use the TAB key to move the cursor to eth0.
4. Press the down arrow key to move the cursor to
eth1.
5. Use the TAB key to move the cursor to the IP
Address field in the IP Configuration column.
6. Type the IP address that the manufacturer used
to configure the router. Or, use the screen
default.
7. Press the TAB key to move the cursor to the
Network field in the IP Configuration column.
8. Type the same address that you entered in the
IP Address field, but substitute a 0for the last
number.
9. Press the TAB key to move the cursor to the
Network Mask field in the IP Configuration
column.
10. Type the address that you received from the
network administrator.
11. Press the TAB key to move the cursor to the
Broadcast field in the IP Configuration column.
12. Type the same address that you entered in the
IP Address field, but substitute 255 for the last
number.
13. Use the ^Qcommand to return to the setup
menu (Figure 4 on page 4).
14. Go to Configure arc0 from the NETWORK
CONFIGURATION screen on page 7.
Figure 7: Sample NETWORK CONFIGURATION screen for eth1

7 3270 3319 Rev B
Configure arc0 from the NETWORK
CONFIGURATION screen
To configure ARCNET 0 (arc0), repeat the procedure
for configuring eth0 with one exception: use the
arrow key to move the cursor to arc0 prior to tabbing
to the IP Address field in the IP Configuration
column.
After you configure arc0, repeat the ^Qcommand to
return to the setup menu (Figure 4 on page 4) then
go to Configure the default gateway from the NETWORK
CONFIGURATION screen.
Configure the default gateway from
the NETWORK CONFIGURATION
screen
Configure the default gateway at the NETWORK
CONFIGURATION screen:
1. At the setup menu (Figure 4 on page 4), use the
TAB key to move the cursor to Network
Configuration.
2. Press ENTER. The NETWORK
CONFIGURATION screen displays
(Figure 6 on page 5).
Note:
The bottom of the NETWORK
CONFIGURATION screen shows the navigation
commands. The most commonly used commands
are TAB, +, and ^Q(CTRL key and Qkey pressed
simultaneously). The ^Q(return) command
steps the display back through the program.
3. Use the TAB key to move the cursor to the
Default Gateway field.
4. Type the Default Gateway address that you
received from the network administrator.
5. Use the ^Qcommand to return to the setup
menu (Figure 4 on page 4).
6. Go to Configure BBMDs.
Configure BBMDs
Configure the BBMDs at the broadcast distribution
table (BDT). For detailed information about BBMDs
and BDTs see engineering bulletin Tracer Summit®
BACnet/IP Network Installations (BAS-PRB004-
EN). To configure the BBMDs:
1. At the setup menu (Figure 4 on page 4), use the
TAB key to move the cursor to Port Table.
2. Press ENTER. The PORT TABLE screen displays
(Figure 5 on page 4).
3. Use the TAB key to move the cursor to the
BACnet/IP Detail column.
4. Press the +key to move the cursor to BBMD.
5. Press ENTER. The BBMD DETAILS/BDT
ENTRIES screen displays (Figure 8).
Note:
The bottom of the BBMD DETAILS/BDT
ENTRIES screen shows the navigation
commands. The most commonly used commands
are TAB, +, and ^Q(CTRL key and Qkey pressed
simultaneously). The ^Q(return) command
steps the display back through the program.
Figure 8: Sample BBMD DETAILS and BDT ENTRIES screen
First field

3270 3319 Rev B 8
6. At the BBMD DETAILS portion of the screen,
use the TAB key, if necessary, to move the cursor
to FDT is present? <support FD?>.
7. Press SHIFT +and when the menu appears, use
the down arrow key to select on.
8. Press the TAB key to move the cursor to
Maximum size of FDT.
9. Type the number of FDs (routers) that are on the
network.
10. Use the TAB key to move the cursor to the UDP
Port column on the BDT ENTRIES portion of the
screen. The cursor is at the first field.
11. Type the UDP port number that you received
from the network administrator.
12. Press the TAB key to move the cursor to the IP
address column.
13. Type the address that you received from the
network administrator.
14. Press the TAB key to move the cursor to the
Subnet Mask column.
15. Type the address that you received from the
network administrator.
Note:
All other fields remain in their default state.
16. Repeat steps 10 through 15 for each BBMD on
the network with one exception: at the UDP Port
column, use the down arrow key to access the
next available field.
17. When all BBMDs are configured, use the ^Q
command to return to the setup menu
(Figure 4 on page 4).
18. Go to Exit the editor and reboot.
Exit the editor and reboot
When all of the parameters are set, save changes,
exit the editor, and reboot the router.
1. Repeat the ^Qcommand until a message
appears asking if you want to save and write to
the disk.
2. Select Y (yes).
3. When asked if you want to reboot, select Y (yes).
The router reboots.
Note:
When the write operation completes, the screen
returns to the command prompt.
4. Disconnect from the terminal emulator and close
the screen.
Troubleshooting
After the router is installed and configured, verify
proper operation. To verify proper operation, test
communications from a network PC to the router:
1. At the DOS prompt on a network PC, type ping
followed by the IP address for eth0:
ping <IP address for eth0>
Note:
Type the IP address, but not the carets (<>).
2. Press ENTER.
3. When the operation completes and the results
are returned, note the number of packets sent,
the number of packets received, and the elapsed
time for the operation.
4. If the operation fails, configure the router again.
5. If the ping completes, but the Tracer Summit PC
Workstation does not communicate, check the
workstation setup. For more information, see
engineering bulletin Tracer Summit®BACnet/
IP Network Installations (BAS-PRB004-EN).
Contact information
Trane BAS is the contact for technical support for
the router.
Tracer Summit, Trane, and the Trane logo are trademarks of Trane in the United States and other
countries. All trademarks referenced in this document are the trademarks of their respective owners.