Transition Networks EOCPxx4020-110 User manual

Transition Networks EOCPxx4020-110 Quick Start Guide
33689 Rev. A https://www.transition.com Page 1of 2
EOCPxx4020-110 Quick Start Guide
Introduction
Transition Networks’ EOCPxx4020-110 Ethernet over Coax Extenders with PoE+
deliver near Gigabit data and PoE over Coax, letting you leverage your current
Coax infrastructure when upgrading to IP cameras and surveillance systems.
See the full EOC User Guide for Product Numbers, Applications, Configuration Examples, Features, Package Contents,
Port Descriptions, Web Config pages, Technical Specifications, Warranty and Compliance info, Error Messages, and
Troubleshooting.
Installation
Note: See the EOC User Guide for important Cautions and Warnings including Operating temperature, Air Flow,
Mechanical Loading, Circuit Overloading, etc.
Mounting Install the EOC units indoors (or in an appropriately rated enclosure).
Securely mount the EOC units. Do not support the EOC units by the attached
cables. Use an optional Mounting bracket to mount the EOC unit to a wall or other
structure. Mount an EOC unit onto a DIN rail using an optional DIN Rail Mount Kit.
See the User Guide for specific mounting options (ordered separately).
Front Panels: Local Device (top right) Remote Device (bottom right):
Connections
Coax Cable Connection: Connect the EOCPSE4020-110 unit’s BNC connector to
the coaxial cable. If an EOCPPD4020-110 unit is connected at the far end and powered up, then
the green DATA LED will light steadily to indicate a good connection. Only two units should be
connected, one at each end of the cable. The EOCPxx4020-110 is not compatible with other
equipment such as analog video amplifiers.
Combo (Shared) Port: note that in terms of copper versus fiber port selection / priority, only
one port can be active at any given time; by default the SFP port takes precedence over the copper port (configurable on
Ethernet Web GUI page).
SFP / Fiber Connection: The EOC lets you install an SFP optic of your choice in order to make a
fiber connection. The EOC has a single SFP port. The SFP port supports any MSA compliant
1000Base-X SFP module. For temperatures above +50 C, industrial SFP modules (+85 C) must
be used. Install and connect Single-strand or Two-strand Fiber Cable.
Ethernet Cable Connection: Connect the EOCPD4020-110 RJ45 Ethernet jack to the camera or
other network equipment using a standard Ethernet cable. Both patch and crossover type
Cat5 or Cat6 cables are supported. The Combo Port Link/ACT LED will light to indicate a network connection, and will
blink off during network activity.
Power over Ethernet: Using the PoE option, the EOCPSE4020-110 can automatically enable delivery of up to 30 watts of
POE (IEEE 802.3at - Class 4) to compatible network devices, via its Ethernet port.
Remote: IEEE 802.3at PSE at 30W. Local Power Source: DIN or TB (48V@45W). Remote POE-PSE: IEEE 802.3at - Class 4.
Power Out: 30 W. Power at PD: 25.5W.
Install the RJ-45 Copper Cable: 1. Locate a 10/100/1000Base-TX compliant copper cable with male RJ-45 connectors
installed at both ends. 2. Connect the RJ-45 connector at one end of the cable to the EOCPxx4020-110
10/100/1000Base-RJ-45 port. 3. Connect the RJ-45 connector at the other end of the cable to the 10/100/1000Base-RJ-
45 port on the other device (camera, wireless access point, etc.). Note: The AutoCross feature allows either straight-thru
or crossover cables.

Transition Networks EOCPxx4020-110 Quick Start Guide
33689 Rev. A https://www.transition.com Page 2of 2
Powering the EOC
The 90W Power supply, 25148 is an option for powering the Local PSE unit,
and is optional for use with the Remote PD unit. The PWR LED will blink to
indicate the presence of power to the EOCPxx4020-110. (For indoor use only.)
The Local and Remote unit Power Supplies do not provide isolated, redundant
or load sharing capabilities.
48 VDC IN Options: The two 48 VDC input options are the 4-Pin Mini DIN
(near right) and the 2-Pin Terminal Block (far right). Note: use the flat-topped grip
to remove the power supply cable from the 48VDC IN 4-Pin Mini DIN connection.
Local PSE (EOCPSE4020-110) Power Input Options:
1. A 4-Pin mini DIN with the designated AC to DC adapter OR
2. A 2-Pin Terminal Block connectors for +48 VDC power source that must meet IEEE 802.3 af/at isolation requirements
of 1500VAC or 2250 VDC.
Remote PD (EOCPD4020-110) Power Input Options:
1. A 4-Pin mini DIN with the designated AC to DC adapter OR
2. A 2-Pin Terminal Block connectors for +48 VDC power source that must meet IEEE 802.3 af/at isolation requirements
of 1500VAC or 2250 VDC. OR
3. PoE input power to the Remote unit from the Local unit via the Coax cable.
Software Operation
Web GUI Configuration: The Web GUI lets you access the Login page and subsequently the various configuration pages
(Coax, IP, Ethernet, Device, Auto Power Reset, and Advanced) and Status (Power, SFP, and Remote Upgrade Status) pages.
The default IP address is 192.168.0.1 (Local) and 192.168.0.2 (Remote). The default password is admin.
TN EoCP Tool: lets you discover and configure local and remote nodes, and allows firmware upgrades. The TN Ethernet
Extender Tool User Guide (33696) is available as a download from the TN website.
Status LEDs
PWR: Power and bootloader status: Power applied: Green - ON.
Firmware update in progress: Orange – ON and/or BLINK.
COAX: Power delivery (local) or sourcing (remote) status and/or
fault: see User Guide for Local vs. Remote unit LED descriptions.
DATA – Coax data link; Linked: Green – BLINK.
SECURITY (Coax): Secure mode, pairing mode, and key/config state: Not secure: OFF. Secure: Green – ON.
In Config mode: Green – Slow BLINK. In Pairing mode: Green – Fast BLINK. Received key & finished config: Green – 3 BLINKS.
Link/ACT - 1GE TP or Fiber port: 1000Mbps: Green - ON link, BLINK activity. 100Mbps: Green and Yellow - ON link, BLINK activity.
10Mbps:Yellow - ON link, BLINK activity.
POE – Power Over Ethernet status (Remote PD unit only): No PD detacted: OFF. Power applied: Green – ON. Detact fault: Yellow –
ON: Fault or Remote is not a PoE device. Classification fault: Yellow - BLINK.
RESET button: If doing security Pairing for coax encryption, do before final deployment of Local PSE and Remote PD units in the field.
See User Guide for full details, as the RESET button performs other functions, and you could lose Remote PD unit connection.
Transition Networks: 10900 Red Circle Drive * Minnetonka, MN 55343 USA * Tel: [phone] *
* Toll Free: 800.526.9267 * Fax: [phone] * [e-mail] * * [e-mail] *
[e-mail] *