Transition Networks C/F-SM-MM-02(LH) User manual

COMPLIANCE INFORMATION
UL Listed
C-UL Listed (Canada)
CISPR/EN55022 Class A
FCC Regulations
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference, in which case the user will be
required to correct the interference at the user’s own expense.
Canadian Regulations
This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on
the radio interference regulations of the Canadian Department of Communications.
Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables
aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique
édicté par le ministère des Communications du Canada.
European Regulations
Warning
This is a Class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
Achtung !
Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb dieses Gerätes
Rundfunkstörungen auftreten, in weichen Fällen der Benutzer für entsprechende Gegenmaßnahmen
werantwortlich ist.
Attention !
Ceci est un produit de Classe A. Dans un environment domestique, ce produit risque de créer des
interférences radioélectriques, il appartiendra alors à l’utilsateur de prende les measures spécifiques
appropriées
Trademark Notice
All registered trademarks and trademarks are the property of their respective owners.
Copyright Restrictions
© 1997-2000 TRANSITION Networks.
All rights reserved. No part of this work may be reproduced or used in any form or by any means –
graphic, electronic, or mechanical – without written permission from TRANSITION Networks.
Printed in the U.S.A. 33046.D
Designed to be installed in the TRANSITION Networks E-MCC-1600 Media
Converter Chassis, the protocol-independent TRANSITION Networks C/F-SM-
MM-02 series 155 Mb/s Singlemode/ Multimode media converters connect
singlemode fiber-optic cable to multimode fiber-optic cable.
C/F-SM-MM-02
Provides a set of RX (receive) and TX (transmit) SC connectors to singlemode fiber-
optic cable and a set of RX (receive) and TX (transmit) SC connectors to
multimode fiber-optic cable.
The C/F-SM-MM-02 media converters can be installed in any 155Mb/s (or slower)
fiber network. NOTE: C/F-SM-MM-02 media converters function in half-duplex
mode or, when connected to devices capable of full-duplex connectivity, in full-
duplex mode.
Minneapolis, MN 55344 USA
155 Mb/s Singlemode/Multimode
Media Converters
C/F-SM-MM-02, C/F-SM-MM-02(LH), C/F-SM-MM-02(XL),
C/F-SM-MM-02(LW)
USER’S GUIDE
Power Modules
Media
Conversion
Center
Power
In Use
Power
In Use
1
2
Management
Module
Power
Link
TX
RX
CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE
PUBLIC TELEPHONE NETWORK. Failure to observe this caution could result in
damage to the public telephone network.
Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EG-Mitgliedstaaten
verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der Richtlinie 91/263/EWG zur
Angleichung der Rechtsvorschriften der Mitgliedstaaten über Telekommunikationsendeinrichtungen
einschliesslich der gegenseitigen Anerkennung ihrer Konformität.
C/F-SM-MM-02 in the Network . . . . .2
Installation . . . . . . . . . . . . . . . . . . . .3
Operation . . . . . . . . . . . . . . . . . . . . .4
Fault Isolation and Correction . . . . .5
Cable Specifications . . . . . . . . . . . . .6
Technical Specifications . . . . . . . . . .7
Compliance Information . . . . . . . . . .8

C/F-SM-MM-02 IN THE NETWORK
NOTE: This product is NOT a repeater. Therefore, maximum distances depend on
specific characteristics of the installation. The full distances of BOTH singlemode
and multimode fiber MAY NOT be supported in the same installation.
TECHNICAL SPECIFICATIONS
Standards IEEE 802.3u
Case Dimensions 4.75" x 3.0" x 1.0" (119mm x 76mm x 25mm)
Shipping Weight 3 pounds (1.4 kilograms)
Environment Temperature: 0-40°C (32° to 104° F )
Humidity 10-90%, non condensing
Altitude 0-10,000 feet
Warranty Lifetime
DECLARATION OF CONFORMITY
Name of Mfg: Transition Networks
6475 City West Parkway, Minneapolis MN 55344 USA
Model: C/F-SM-MM-02 Series Media Converters
Part Number(s): C/F-SM-MM-02,C/F-SM-MM-02(LH),C/F-SM-MM-02(XL),
C/F-SM-MM-02(LW)
Regulation: EMC Directive 89/336/EEC
Purpose: To declare that the C/F-SM-MM-02 to which this declaration refers is
in conformity with the following standards.
EMC-CISPR 22: 1985 Class A; EN 55022: 1988 Class A; EN 50082-1:1992;
EN 60950 A4:1997; IEC 801.2, IEC 801.3, and IEC 801.4; IEC 950
I, the undersigned, hereby declare that the equipment specified above conforms to the
above Directive(s) and Standard(s).
_January 1, 1997_____
Stephen Anderson, Vice-President of Engineering Date
Singlemode
Multimode
Singlemode
Multimode
Multimode

CABLE SPECIFICATIONS
The physical characteristics of the media cable must meet or exceed IEEE 802.3 specifications.
155 Mb/s Fiber Specifications
Bit error rate: ≤10-9
MULTIMODE
Fiber Optic Cable Recommended: 62.5 / 125 µm multimode fiber
Optional: 100 / 140 µm multimode fiber
85 / 125 µm multimode fiber
50 / 125 µm multimode fiber
Fiber Optic Transmitter Power: min: -19.0 dBm max: -14.0 dBm
Fiber Optic Receiver Sensitivity: min: -32.5 dBm max: -14.0 dBm
Wavelength : 1300 nM
Maximum Cable Distance: 2 kilometers
SINGLEMODE
Fiber Optic Cable Recommended: 9 µm singlemode fiber
C/F-SM-MM-02 1300 nM
Fiber-optic Transmitter Power: min: -15.0 dBm max: -8.0 dBm
Fiber-optic Receiver Sensitivity: min: -32.5 dBm max: -8.0 dBm
Maximum Cable Distance: 20 kilometers
C/F-SM-MM-02(LH) 1300 nM
Fiber-optic Transmitter Power: min: -8.0 dBm max: -0.0 dBm
Fiber-optic Receiver Sensitivity: min: -34.0 dBm max: -8.0 dBm
Minimum Cable Distance: 15 kilometers
Maximum Cable Distance: 40 kilometers
C/F-SM-MM-02(XL) 1300 nM
Fiber-optic Transmitter Power: min: -5.0 dBm max: 0.0 dBm
Fiber-optic Receiver Sensitivity: min: -34.0 dBm max: -7.0 dBm
Minimum Cable Distance: 15 kilometers
Maximum Cable Distance: 60 kilometers
C/F-SM-MM-02(LW) 1550 nM
Fiber-optic Transmitter Power: min: -5.0 dBm max: -0.0 dBm
Fiber-optic Receiver Sensitivity: min: -34.0 dBm max: -7.0 dBm
Minimum Cable Distance: 30 kilometers
Maximum Cable Distance: 80 kilometers
INSTALLATION
Install Slide-In-Module in E-MCC-1600 Chassis
NOTE: Media Converter Slide-in-Modules can be installed in any
installation slot, in any order.
•Remove Media Converter Slide-in-Module protective plate from selected
installation slot by removing two (2) screws that secure plate to front of
E-MCC-1600.
•Carefully slide Media Converter Slide-in-Module into installation slot,
aligning Media Converter Slide-in-Module with installation guides.
NOTE: Ensure that the Media Converter Slide-in-Module is firmly seated
against the backplane.
•Secure Slide-in-Module by securing panel fastener screw attached to
Slide-in-Module to E-MCC-1600 chassis.
Install Cable
NOTE: Be sure to connect correct speed fiber cable at each connector.
•Locate or build fiber cable with male two-stranded TX to RX connectors
appropriate to the media converter installed at both ends.
•Connect male TX and RX cable connectors at one end of cable to TX
and RX female connectors, respectively, on media converter.
•Connect male TX and RX cable connectors at other end of cable to RX
and TX connectors of 802.3 compliant fiber device.

OPERATION
After installation, the media converter should function without operator
intervention.
Status LEDs
Use the status LEDs to monitor media converter operation in the network.
P(o)w(e)r Illuminated
green LED
indicates
connection to
external AC
power.
Link Steady green
LED indicates that fiber link is connected properly.
FAULT ISOLATION and CORRECTION
If the media converter fails, isolate and correct the failure by determining the
answers to the following questions and then taking the indicated action:
1. Is the power LED on the media converter illuminated?
NO
•Ensure that media converter is seated firmly in E-MCC-1600 chassis?
•Contact Technical Support at [phone]/ (800) LAN-WANS.
YES
•Proceed to step 2.
2. Is the multimode fiber Link LED illuminated?
NO
•Check fiber cables for proper connection.
•Verify that TX and RX cables on media converter are connected to
RX and TX ports, respectively, on the other device.
•Power-cycle the media converter.
•Refer to Tech Tips available at: http://www.transition.com
•Contact Technical Support at [phone]/ (800) LAN-WANS.
YES
•Proceed to step 3.
3. Is the singlemode fiber Link LED illuminated?
NO
•Check fiber cables for proper connection.
•Verify that TX and RX cables on media converter are connected to
RX and TX ports, respectively, on the other device.
•Power-cycle the media converter.
•Refer to Tech Tips available at: http://www.transition.com
YES
•Contact Technical Support at [phone]/ (800) LAN-WANS.