Transition Networks ARCNET AR-CF-02 User manual

MEDIA CONVERTER TECHNICAL SPECIFICATIONS
Standards ANSI/ATA 878
Delay 300ns one-way
Case dimensions 4.75" x 3.0" x 1.0" (119mm x 76mm x 25mm)
Shipping Weight 2 pounds (0.9 kilograms)
Environment Temperature: 0-40°C (32° to 104° F )
Humidity 10-90%, non condensing
Altitude 0-10,000 feet
Warranty Five years
Power Supply Requirements Replace power supply with only the equivalent
input rating (see below) and output rating (regulated 9VDC at 0.2 A).
TN PN Requirement Location
3525 240 volts, 50 hertz United Kingdom
3525 230 volts, 50 hertz Europe
3518 120 volts, 60 hertz USA/Canada/Mexico
3514 100 volts, 50-60 hertz Japan
3525 240 volts, 50 hertz Australia
NOTE: This product also can be powered by the Transition Networks E-MCR series media
converter rack.
Compliance Information
UL Listed
C-UL Listed (Canada)
CISPR/EN55022 Class A
FCC Regulations
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference, in which case the user will be
required to correct the interference at the user’s own expense.
Canadian Regulations
This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on
the radio interference regulations of the Canadian Department of Communications.
European Regulations
Warning
This is a Class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
Copyright Restrictions
© 1999 TRANSITION Networks.
All rights reserved. No part of this work may be reproduced or used in any form or by any means –
graphic, electronic, or mechanical – without written permission from TRANSITION Networks.
Trademark Notice
ARCNET is a registered trademark of Datapoint Corporation.
All registered trademarks and trademarks are the property of their respective owners. 33095.B
The TRANSITION Networks ARCNET®Coax Copper/Fiber Media Converter
(AR-CF-02) extends the signal distance of an ARCNET®segment or node
linkupto2kilometers over fiber*, up to 600 meters over coax cable in a star
topology, and up to 300 meters over coax cable in a bus topology.
A switch on the media converter allows the media converter to be used to
terminate the link or node signal.
STATUS LEDS
Power Steady green LED indicates connection to external AC power.
Coax Blinking green LED
indicates network
traffic on coaxial cable
link.
Fiber Blinking green LED
indicates network traffic on fiber link.
*Consider carefully the network constraints imposed by the maximum latency
response time of installed equipment. Some equipment cannot handle the extended
response time that 2 kilometers of fiber introduces.
Minneapolis, MN 55344 USA
ARCNET®Coax Copper/Fiber Media Converter
AR-CF-02, AR-CF-02(SC), AR-CF-02(SM)
USER’S GUIDE
10BASE-T
RX
TX
Fiber
Power
Coax
AR-CF-02
Provides a BNC
connector to coaxial
cable and a set of RX
(receive) and TX
(transmit) ST connectors
to multimode fiber-optic
cable.
AR-CF-02(SC)
Provides a BNC connector to
coaxial cable and an RX (receive)
and TX (transmit) SC connector to
multimode fiber-optic cable.
AR-CF-02(SM)
Provides a BNC connector to
coaxial cable and an RX (receive)
ST and TX (transmit) SC connector
to singlemode fiber-optic cable.
AR-CF-02
ArcNet Fiber to Coax Media Converter
®

Installation NOTES
Install Coax Copper
STAR TOPOLOGY
• MAXIMUM coax segment to active hub is 600 meters (2000
feet) on RG-62 cable; minimum does not apply.
BUS TOPOLOGY
• Devices attached to coax bus must be located AT LEAST six
(6) feet apart.
• MAXIMUM coax bus length is 300 meters (1000 feet);
minimum is 1.8 meters (6 feet).
• Device(s) attached to EACH END of bus must be terminated.
NOTE: If the media converter is installed at one end of the
bus, use the configuration switch to terminate the media
converter.
CONFIGURATION SWITCH
NOTE: Set configuration switch (located on the side of media converter)
according to site installation requirements:
Switch 1 NOT USED
Switch 2 UP = OFF Media converter TRANSFERS signal
DOWN = ON Media converter TERMINATES signal.
Install Fiber
• Connect one end of first fiber cable to AR-CF-02 media
converter TX connector.
• Connect other end of that fiber cable to second AR-CF-02
media converter RX connector.
• Connect one end of second fiber cable to AR-CF-02 media
converter RX connector.
• Connect other end of that fiber cable to AR-CF-02 media
converter TX connector.
Power
• Locate correct power supply adapter for site installation.
• Connect media converter power connector at end of power
supply adapter cord to AR-CF-02 media converter power
receptacle.
• Connect 2-prong or 3-prong external power connector on
other end of power supply adapter cord to external AC power.
CABLE SPECIFICATIONS
The physical characteristics of the cable must meet or exceed the following:
FIBER CABLE
MULTIMODE
Fiber Optic Cable Recommended: 62.5 / 125 µm multimode fiber
Fiber Optic Transmitter Power: min: -19.0 dBm max: -14.0 dBm
Fiber Optic Receiver Sensitivity: min: -32.5 dBm max: -14.0 dBm
Wavelength: 850nM
Bit error rate: ≤10-9
Maximum Cable Distance: 2 kilometers
SINGLEMODE
Fiber Optic Cable Recommended: 9 µm singlemode fiber
Fiber Optic Transmitter Power: min: -27.0 dBm max: -17.0 dBm
Fiber Optic Receiver Sensitivity: min: -32.5 dBm max: -13.0 dBm
Wavelength: 1300nM
Bit error rate: ≤10-9
Maximum Cable Distance: 8 kilometers
COAX CABLE/STAR TOPOLOGY
RG-62 Cable
Cable Characteristics:
Cable type: Coaxial RG-62/u
Impedance: 75 Ω@ 10 MHz
Mutual Capacitance: 13 pF/ft ±20% @ 10 MHz
Maximum Attenuation: 5.5 dB/1000 feet
Maximum Cable Distance: 600 meters (2000 feet)
Minimum Distance/Connection: 0 meters (0 feet)
RG-59 Cable
Cable Characteristics:
Cable type: Coaxial RG-59/u
Impedance: 93 Ω@ 10 MHz
Mutual Capacitance: 13 pF/ft ±20% @ 10 MHz
Maximum Attenuation: 7.0 dB/1000 feet
Maximum Cable Distance: 450 meters (1500 feet)
Minimum Distance/Connection: 0 meters (0 feet)
COAX CABLE/BUS TOPOLOGY
RG-62 Cable
Cable Characteristics:
Cable type: Coaxial RG-62/u
Impedance: 93 Ω@ 10 MHz
Mutual Capacitance: 13 pF/ft ±20% @ 10 MHz
Maximum Attenuation: 5.5 dB/1000 feet
Maximum Cable Distance: 300 meters (1000 feet)
Minimum Distance/Connection: 1.8 meters (6 feet)
AR-CF-02