Transition Networks IONPS-A User manual

IONPS-A
AC Power Module
User Manual
33423.A

IONPS-A, AC Power Module
2Tech Support: 1-800-260-1312 – International: 00-1-952-941-7600 – (24 hours)
Table of contents
Cautions and Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Cautions and warnings in this manual . . . . . . . . . . . . . . . . . . . . . . . . .3
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Power Module component identification . . . . . . . . . . . . . . . . . . . . . . .4
Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Power Module redundancy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Installing an optional Power Module into the ION chassis . . . . . . . . .6
Connecting external power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Replacing the Power Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Replacing the fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Technical Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Contact Us . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Compliance Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
[email protected] – Click the “Transition Now” link for a live Web chat. 3
Cautions and Warnings
Definitions
Cautions indicate potential damage to equipment.
Warnings indicate a potential hazard or injury to people.
Cautions and warnings in this manual
Cautions and warnings are explained here and placed throughout this manual where
appropriate.
CAUTION: While installing or servicing the Power Module, wear a grounding
device and observe all electrostatic discharge precautions. Failure to observe this
caution could result in damage or failure of the Power Module.
WARNING: Do not connect the Power Module to an external power source before
installing it into the chassis. Failure to observe this warning could result in an
electrical shock, even death.
WARNING: A readily accessible, suitable National Electrical Code (NEC) or
local electrical code approved disconnect device and branch-circuit protector must
be part of the building's installed wiring to accommodate permanently connected
equipment. Failure to observe this warning could result in an electric shock, even
death.
WARNING: Turn the Power Module and external power source OFF and ensure
that the Power Module is disconnected from the external power source before
performing any maintenance. Failure to observe this warning could result in an
electrical shock, even death.

IONPS-A, AC Power Module
4Tech Support: 1-800-260-1312 – International: 00-1-952-941-7600 – (24 hours)
Figure 1: Power Module Components
Description
Transition Networks’ IONPS-A, AC Power Module can deliver power or provide
optional, redundant AC power to an ION219-A chassis. See the ION219-A chassis
manual #33421. You can download the manual @ www.transition.com, then click on
Product/Product Finder.
Power Module component identification
See Figure 1:
1 Fans (two fans exhaust warm air from the IONPS-A, AC Power Module)
2 Power LED (ON green when powered up)
3 ON/OFF switch, when in the ON position power is supplied to the ION chassis
4 Fuse (inline AC)
5 Handle
6 AC Power Receptacle for an AC power plug
7 Dry Contact Relay (optional)
Note: The IONPS-A, AC Power Module has instant failover capability.
1
5
3
7
4
1
2
6
[email protected] – Click the “Transition Now” link for a live Web chat. 5
Installation
IMPORTANT
• All installation and service must be performed by qualified personnel only.
• Read, understand, and follow all CAUTION and WARNING notices, instructions
marked on the product, including in this manual.
The IONPS-A, AC Power Module can replace an existing IONPS-A, AC Power
Module or it can be installed as the redundant Power Module in an AC powered
ION219-A chassis.
CAUTION: While installing or servicing the Power Module, wear a grounding
device and observe all electrostatic discharge precautions. Failure to observe this
caution could result in damage or failure of the Power Module.
Description — continued
Notices
• The IONPS-A, AC Power Module must be installed by qualified technical
personnel only. Transition networks assumes no responsibility for the improper
installation, set up, or use of the IONPS-A, AC Power Module.
• The information in this user’s guide is subject to change. For the most up-to-date
information, see the user’s guide on-line to download the current version of the
manual at www.transition.com under Products.
Power module redundancy
The IONPS-A, AC Power Module includes Instant Fail-Over (IFO) circuitry that
provides the capability for the primary Power Module to power the chassis backplane
while the auxiliary Power Module is in ‘hot’ standby mode. If the IFO circuitry detects
the loss of primary power, the auxiliary Power Module instantly provides power to the
chassis backplane. When primary power is restored, the IFO circuitry places the
auxiliary Power Module in ‘hot’ standby mode. The chassis primary Power Module is
located in the left slot of the chassis as viewed from the rear. The chassis auxiliary
Power Module is located in the right slot of the chassis as viewed from the rear. A
single Power Module placed in either location can power the chassis backplane.
Note: The IONPS-A, AC Power Modules DO NOT load share.

IONPS-A, AC Power Module
6Tech Support: 1-800-260-1312 – International: 00-1-952-941-7600 – (24 hours)
Installing an optional Power Module into the ION chassis
WARNING: Do not connect the Power Module to an external power source before
installing it into the chassis. Failure to observe this warning could result in an
electrical shock.
Note: The Power Module is hot swappable (i.e., swapped while the chassis is in
operation) provided the ON/OFF switch of the Power Module is in the OFF
position, and it has been disconnected from its external power source.
To install the Power Module in the ION chassis, do the following:
Note: The procedure is the same for installing the Power Module into either slot.
1. Push the Power Module ON/OFF switch to the OFF position. See Figure 2.
Power Module
Switch OFF Position
Figure 2: Power ON/OFF Switch
Installation — Continued
[email protected] – Click the “Transition Now” link for a live Web chat. 7
3. Remove the slot cover from the right chassis slot and keep the two screws. See
Figure 4.
2. If necessary, remove the grounding hardware from the chassis before installing or
removing the Power Module. See Figure 3.
Installing an optional Power Module into the ION chassis — continued
Installation — Continued
SlotCover
Screws
Compression Lugs
Kepsnuts
Chassis
Grounding
Posts
(Not Provided )
(provided)
Figure 4: Chassis Slot Cover
Figure 3: Chassis Grounding Hardware

IONPS-A, AC Power Module
8Tech Support: 1-800-260-1312 – International: 00-1-952-941-7600 – (24 hours)
Figure 5: Power Module Installation
Figure 6: Power Module Installation
Note: Once the optional Power Module is seated to the backplane of the chassis,
the fans will become operational.
4. Position the Power Module at the chassis slot, as shown in Figure 5.
5. Side the Power Module completely into the chassis. See Figure 6.
Mounting Screws
Chassis
Power Module
Chassis
Installed Optional
Power Module
Installation — Continued
Installing an optional Power Module into the ION chassis — continued
Connecting the Power Module to external power
To connect external power to the IONPS-A, AC Power Module, do the following:
1. Locate the power cord for the Power Module.
2. Make sure that the Power Module ON/OFF switch is in the OFF position. See
Figure 7.
3. Plug the female end of the AC power cord into the AC power receptacle on the
Power Module. See Figure 7.
4. Plug the male end of the AC power cord into the AC power source.
5. Turn the power ON/OFF switch to the ON position. See Figure 7.
Note: Once the power ON/OFF switch is in the ON position, the power ON LED
will lite. This means that the optional Power Module is ready to power the
chassis if the primary Power Module fails.
Important: There is NO power sharing between the two Power Modules.
[email protected] – Click the “Transition Now” link for a live Web chat. 9
Figure 7: AC Power Cord Ends
6. Insert the two screws to mount the Power Module to the chassis.
Installation — Continued
Installing an optional Power Module into the ION chassis — continued
AC Power Cord
(female end)
Power Module
Power Cord
Receptacle
AC Power Cord
(male end)
Power Module
ON/OFF Switch

Maintenance
Replacing the Power Module
WARNING: Do not connect the Power Module to the external power source before
installing it into the chassis. Failure to observe this caution could result in equipment
damage and/or personal injury or death.
To replace the Power Module, do the following:
1. Turn the power ON/OFF switch to the OFF position.
2. Disconnect the AC power cord from the power source.
3. In necessary, remove the chassis grounding assembly. See Figure 8.
IONPS-A, AC Power Module
10 Tech Support: 1-800-260-1312 – International: 00-1-952-941-7600 – (24 hours)
Figure 9: Removing Power Module
Figure 8: Chassis Grounding Hardware
Grounding Terminal
Lug (Not Provided)
Nuts & Washers
(Not Provided)
Chassis
Frame
Mounting Screws Power Module
Chassis
4. Remove the two screws securing the Power Module to the chassis.
5. Carefully pull the Power Module from the chassis. See Figure 9.
[email protected] – Click the “Transition Now” link for a live Web chat. 11
Figure 10: Power ON/OFF Switch
Maintenance — Continued
Installing the Power Module — continued
6. Locate the new Power Module.
7. Push the power ON/OFF switch to the OFF position.
8. Position the Power Module at the chassis slot, as shown in Figure 10.
9. Slide the Power Module complete into the slot.
11. Insert the two screws to secure the Power Module to the chassis.
12. Plug the AC power cord into the AC receptacle on the Power Module.
13. Plug the other end of the cord into an external AC power source.
14. Push the power ON/OFF switch to the ON position. The power ON LED
should be lit and the fans will be operational.
Mounting Screws
Power
Module
Chassis
Guide

IONPS-A, AC Power Module
12 Tech Support: 1-800-260-1312 – International: 00-1-952-941-7600 – (24 hours)
Maintenance — Continued
Replacing the fuse
CAUTION: Ensure that the IONPS-A, AC Power Module has been disconnected from
the external power source and the ON/OFF switch is at “0.” Failure to observe this
caution could result in damage or failure of the Power Module.
To replace the fuse in the IONPS-A, AC Power Module:
1. Ensure the ON/OFF switch on the Power Module is in the OFF position.
2. Disconnect the AC power cord from the external power source.
3. Insert a small flat blade screwdriver into the groove on the front, inside edge of the
fuse holder, as shown in Figure 11A.
4. Carefully pull the fuse holder from the Power Module. See Figure 11B.
Fuse
Holder
Fuse
Place Small Flathead
Screw Driver Here
(A ) (B )
Power ON/OFF
Switch
4. Remove the fuse from the fuse holder.
5. The replacement fuse MUST BE the same amperage and voltage rating.
6. Insert the fuse into the holder.
7. Slide the fuse holder fully into the Power Module.
8. Connect the power cord to Power Module and to the external power.
9. Push the power ON/OFF switch to the ON position.
Figures 11 A & B: Replacing Fuse
[email protected] – Click the “Transition Now” link for a live Web chat. 13
Technical Specification
For use with Transition Networks Model IONPS-A, AC Power Module.
Dimensions: 8.3" x 8.4" x 2.7" (211 mm x 211 mm x 69 mm)
Weight: 4 lb. (6.35 kg) approximately
Power Input: 100-240 V, 47/63Hz, 2.35 – 1.1 Amp
(typical with a fully-loaded chassis)
Voltage Tolerance: ± 10%
Low-Line Input Current: 3.5A max.
Inrush Current: 13A max. ( peak starting current) @ high line
Transient Recovery Time: 1ms max.
Power Output: 12VDC at 16.67 Amp max.
Power Factor: >0.6 – 0.95, 10 to 100% load respectively
Fuse: 6.3 Amp/250 Volts
MTBF: Greater than 25,000 hours (MIL-HDBK-217F)
Greater than 68,750 hours (Bellcore7 V5.0)
Environment: Operating temperature: 0 to 50°C (32 to 122°F )
Storage temperature: -25 to 70°C (-13 to 158°F)
Humidity: 5 to 90%, non condensing
Warranty: Lifetime

IONPS-A, AC Power Module
14 Tech Support: 1-800-260-1312 – International: 00-1-952-941-7600 – (24 hours)
Troubleshooting
If the Power Module fails, isolate and correct the failure by determining the answers to
the following questions and then taking the indicated action:
1. Is the Power LED on the IONPS-A, AC Power Module illuminated?
NO
• Is the Power Module inserted properly into the chassis?
• Is the Power Module properly connected to the external power source?
• Does the external power source provide power?
• Contact Technical Support: US/Canada: 1-800-260-1312, International:
00-1-952-941-7600.
YES
• Proceed to step 2.
2. Is the fuse on the IONPS-A, AC Power Module intact?
NO
• CAUTION: See the “Replace the Fuse” section for the proper method
for replacing the fuse to the Power Module.
• Contact Technical Support: US/Canada: 1-800-260-1312, International:
00-1-952-941-7600.
YES
• Contact Technical Support: US/Canada: 1-800-260-1312, International:
00-1-952-941-7600.
[email protected] – Click the “Transition Now” link for a live Web chat. 15
Contact Us
Technical Support
Technical support is available 24 hours a day.
US and Canada: 1-800-260-1312
International: 00-1-952-941-7600
Transition Now
Chat live via the Web with Transition Networks Technical Support.
Log onto www.transition.com and click the Transition Now link.
Web-Based Seminars
Transition Networks provides seminars via live web-based training.
Log onto www.transition.com and click the Learning Center link.
E-Mail
Ask a question anytime by sending an e-mail to our technical support staff.
[email protected]
Address
Transition Networks, 10900 Red Circle Drive, Minnetonka, MN 55343, U.S.A.
telephone: [phone]; toll free: 800-526-9267; fax: [phone]
Declaration of Conformity
Name of Mfg: Transition Networks
10900 Red Circle Drive, Minnetoka, MN 55343 U.S.A.
Model: IONPS-A, AC Power Module 120/240 VAC
Purpose: To declare that the IONPS-A, AC Power Module to which this declaration
refers is in compliance with the following directive(s) and standard(s):
EMC Directive 2004/108/EC; EN 55022:2006+A1:2007 Class A;
EN55024:1998+A1:2001+A2:2003; EN6100-2-3; EN6100-3-3; CFR Title 47 Part 15
Subpart B Class A. Low Voltage Directive: 2006/95/EC; EN60950-1:2006; CFR Title 21
Section 1040.10 Class I.
I, the undersigned, hereby declare that the model number(s) listed in this declaration of
conformity is in compliance with the Directive(s) and Standard(s) herein.
_January, 2010_____
Stephen Anderson, Vice-President of Engineering Date

Trademark Notice
All trademarks and registered trademarks are the property of their respective owners.
Copyright Restrictions
© 2009 – 2010 Transition Networks.
All rights reserved. No part of this work may be reproduced or used in any form or by any means -
graphic, electronic, or mechanical - without written permission from Transition Networks.
Printed in the U.S.A.
Compliance Information
FCC Regulations
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference, in which
case the user will be required to correct the interference at the user's own expense.
Canadian Regulations
This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out
on the radio interference regulations of the Canadian Department of Communications.
Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables
aux appareils numériques de la Class A prescrites dans le Règlement sur le brouillage
radioélectrique édicté par le ministère des Communications du Canada.