Transmitter Solutions 318LIPW4K User manual

Transmitter Flat 318LIPW4K
1A - General information
The Transmitter Solutions - 318LIPW4K Flat Transmitter is a key chain
style transmitter operating at 318 MHz. It has been designed for use
with programmable telephone entry, security, and access control
systems operating with a 318 MHz frequency receiver. The code sent by
the transmitter includes a 16 bit security code which allows up to
65,536 number combinations and 4 bits of facility code which allows
up to 16 facility codes .
CONTENTS
1A - General information
1B - Technical specifications
1C - Main components
1 - TRANSMITTER OVERVIEW
2 - NUMBERING
3 - PROGRAMMING
4 - OPERATION
5 - BATTERY ACCESS
1B - Technical specifications
Operating frequency 318 MHz
Number of keys: 4
Battery : 2 x 3V lithium batteries CR2016
Battery life: 18 - 24 months
Protocol : Linear compatible
Number combinations : 65,536
Different Facilities codes 16
Operating temperature: -20°F÷+131°F (-20°C÷+55°C)
Overall dimensions: 2.48”x 1.27”x 0.417”
Weight: 1 oz. (20 gr.)
The Transmitter Solutions - 318R receiver which operates with this
transmitter has a Wiegand 26 bit format output, which will operate any
type of access control system equipped to accept a 26 bit Wiegand
input. The CR 2016 lithium batteries have a shelf life of about 6 months.
The product fully complies with Part 15 of FCC Regulations and the
European Directives 99/5/CE, 89/336/CEE, 73/23/CEE.
1C - Main components
6 - TROUBLESHOOTING
Manual
Red LED
Key-holder ring
Closing hook
Button A
Button B
Button C Button D
Fig. 1
Transmitter
Solutions
Thank you for choosing a Transmitter Solutions product .
Please read this manual carefully before using the product.
Made in Italy. Copyright © 2006 by Transmitter Solutions

2 - NUMBERING
5 - BATTERY ACCESS
3 - PROGRAMMING
Each transmitter is manufactured and sold with a different factory set
sequence number and facility code.
The transmitter facility code and sequence number must be
programmed into your system memory. Your own installer or reseller will
provide you the necessary instructions for your system.
4 - OPERATION
a. Firmly depress either button until the small red LED illuminates.
b. After the LED has illuminated, release the button. If the device you are
attempting to activate does not respond, repeat steps a. and b. or
consult section 6 (Troubleshooting) of this manual.
ATTENTION ! - Danger of explosion if
the battery is not replaced in the
correct way! Replace only with an
equal or equivalent type!
2 X CR2016
Side (+)
Side (-)
To access the battery act on the top with an edge and open the box (fig.2).
Place the 2 batteries CR2016 with the positive pole upward.
NOTE: Please dispose of the batteries properly according to local laws and
regulations.
Test proper battery installation by verifying that the red LED illuminates when
either button is pushed.
6 - TROUBLESHOOTING
Fault
The system does not receive the transmitter
signal
The transmitter led is OFF
The transmitter led is blinking
The operating range is reduced
The system does not receive the transmitter
signal
The transmitter led is ON.
Solution
Replace the transmitter
battery
Check the power supply
of the receiver
IS-T053TSUK Rev. 2 del 15.7.2010
Fig. 2
The warranty period of 318 transmitters is 24
months, beginning from the manufacturing date of the transmitter.
During this period, if the product does operate correctly, due to a
defective component, the product will be repaired or replaced at the
sole discretion of Transmitter Solutions.
The warranty does not extend to the transmitter case which can be
damaged by conditions outside the control of Transmitter Solutions or to
battery life.
Transmitter Solutions
WARRANTY
Notice
Any changes or modification to equipment not
expressly approved by could void the
manufacturer’s warranty.
Transmitter Solutions
Transmitter Solutions
TRANSMITTER SOLUTIONS
2505 Chandler Avenue, Suite, 1
Las Vegas, NV 89120 -
[phone] - [phone] Fax
[email protected]