Emerson Micro Motion 5700 User manual

Installation Manual
MMI-20029969, Rev AB
February 2020
Micro Motion™ 5700 Transmitters
Installation Manual for FOUNDATION™ Fieldbus

Safety messages
Safety messages are provided throughout this manual to protect personnel and equipment. Read each safety message carefully
before proceeding to the next step.
Safety and approval information
This Micro Motion product complies with all applicable European directives when properly installed in accordance with the
instructions in this manual. Refer to the EU declaration of conformity for directives that apply to this product. The EU declaration
of conformity, with all applicable European directives, and the complete ATEX Installation Drawings and Instructions are available
on the internet at www.emerson.com or through your local Micro Motion support center.
Information affixed to equipment that complies with the Pressure Equipment Directive, can be found on the internet at
www.emerson.com.
For hazardous installations in Europe, refer to standard EN 60079-14 if national standards do not apply.
Other information
Full product specifications can be found in the product data sheet. Troubleshooting information can be found in the configuration
manual. Product data sheets and manuals are available from the Micro Motion web site at www.emerson.com.
Return policy
Follow Micro Motion procedures when returning equipment. These procedures ensure legal compliance with government
transportation agencies and help provide a safe working environment for Micro Motion employees. Micro Motion will not accept
your returned equipment if you fail to follow Micro Motion procedures.
Return procedures and forms are available on our web support site at www.emerson.com, or by phoning the Micro Motion
Customer Service department.
Emerson Flow customer service
Email:
•Worldwide: [email protected]
•Asia-Pacific: [email protected]
Telephone:
North and South America Europe and Middle East Asia Pacific
United States 800-522-6277 U.K. and Ireland 0870 240 1978 Australia 800 158 727
Canada [phone] The Netherlands [phone]
666
New Zealand 099 128 804
Mexico [phone] France [phone]
901
India 800 440 1468
Argentina [phone] Germany 0800 182 5347 Pakistan 888 550 2682
Brazil [phone] Italy [phone] China [phone]
Chile [phone] Central & Eastern [phone]
111
Japan [phone]
Peru [phone] Russia/CIS [phone] South Korea [phone]
Egypt 0800 000 0015 Singapore [phone]
Oman 800 70101 Thailand 001 800 441 6426
Qatar 431 0044 Malaysia 800 814 008
Kuwait 663 299 01
South Africa 800 991 390
Saudi Arabia 800 844 9564
UAE 800 0444 0684
2

Contents
Chapter 1 Before you begin............................................................................................................5
1.1 About this document........................................................................................................................5
1.2 Hazard messages..............................................................................................................................5
1.3 Related documentation....................................................................................................................5
Chapter 2 Planning........................................................................................................................ 7
2.1 Installation checklist.........................................................................................................................7
2.2 Additional considerations for retrofitting existing installations......................................................... 8
2.3 Power requirements......................................................................................................................... 8
Chapter 3 Mounting and sensor wiring........................................................................................ 11
3.1 Mounting and sensor wiring for integral-mount transmitters......................................................... 11
3.2 Mounting transmitters................................................................................................................... 11
3.3 Wire a remote-mount transmitter to the sensor............................................................................. 15
3.4 Ground the meter components...................................................................................................... 18
3.5 Rotate the transmitter on the sensor (optional)..............................................................................19
3.6 Rotate the user interface on the transmitter (optional)...................................................................20
3.7 Rotate the sensor wiring junction box on a remote-mount transmitter (optional).......................... 21
Chapter 4 Wiring the channels..................................................................................................... 23
4.1 Available channels.......................................................................................................................... 23
4.2 Access the wiring channels............................................................................................................. 23
4.3 I/O wiring....................................................................................................................................... 24
4.4 FISCO-input entity parameters....................................................................................................... 25
4.5 Wiring for nonhazardous installations............................................................................................ 26
4.6 Wiring for hazardous installations...................................................................................................29
Chapter 5 Wiring the power supply..............................................................................................35
Chapter 6 Power up the transmitter.............................................................................................37
Chapter 7 Guided setup................................................................................................................39
Chapter 8 Using the display controls............................................................................................ 41
Chapter 9 Available service port connection.................................................................................43
Installation Manual Contents
MMI-20029969 February 2020
Installation Manual iii

Contents Installation Manual
February 2020 MMI-20029969
iv Micro Motion 5700 transmitters for FOUNDATION Fieldbus

1 Before you begin
1.1 About this document
This manual provides information on planning, mounting, wiring, and initial setup of the
5700 transmitter. For information on full configuration, maintenance, troubleshooting, or
service of the transmitter, see the configuration and use manual.
The information in this document assumes that users understand basic transmitter and
sensor installation, configuration, and maintenance concepts and procedures.
1.2 Hazard messages
This document uses the following criteria for hazard messages based on ANSI standards
Z535.6-2011 (R2017).
DANGER
Serious injury or death will occur if a hazardous situation is not avoided.
WARNING
Serious injury or death could occur if a hazardous situation is not avoided.
CAUTION
Minor or moderate injury will or could occur if a hazardous situation is not avoided.
NOTICE
Data loss, property damage, hardware damage, or software damage can occur if a
situation is not avoided. There is no credible risk of physical injury.
Physical access
NOTICE
Unauthorized personnel can potentially cause significant damage and/or misconfiguration
of end users' equipment. Protect against all intentional or unintentional unauthorized use.
Physical security is an important part of any security program and fundamental to
protecting your system. Restrict physical access to protect users' assets. This is true for all
systems used within the facility.
1.3 Related documentation
You can find all product documentation on the product documentation DVD shipped with
the product or at www.emerson.com.
See any of the following documents for more information:
•Micro Motion 5700 Product Data Sheet
•Micro Motion 5700 Transmitters for FOUNDATION™ Fieldbus: Configuration and Use Manual
Installation Manual Before you begin
MMI-20029969 February 2020
Installation Manual 5

•Modbus Interface Tool
•Sensor installation manual
Before you begin Installation Manual
February 2020 MMI-20029969
6 Micro Motion 5700 transmitters for FOUNDATION Fieldbus

2 Planning
2.1 Installation checklist
□If possible, install the transmitter in a location that will prevent direct exposure to
sunlight. The environmental limits for the transmitter may be further restricted by
hazardous area approvals.
□If you plan to mount the transmitter in a hazardous area:
WARNING
—Verify that the transmitter has the appropriate hazardous area approval. Each
transmitter has a hazardous area approval tag attached to the transmitter
housing.
—Ensure that any cable used between the transmitter and the sensor meets the
hazardous area requirements.
—For ATEX/IECEx installations, strictly adhere to the safety instructions
documented in the ATEX/IECEx approvals documentation available on the
product documentation DVD shipped with the product or at www.emerson.com.
□Verify that you have the appropriate cable and required cable installation parts for your
installation. For wiring between the transmitter and sensor, verify the maximum cable
length does not exceed 1,000 ft (305 m).
□Ensure that you use the following cables for the different connections:
—A certified FOUNDATION fieldbus cable for FOUNDATION fieldbus terminals
—A shielded, twisted-pair instrument cable with drain for all output connections
□You can mount the transmitter in any orientation as long as the conduit openings or
transmitter display do not point upward.
Installing the transmitter with the conduit openings or transmitter display facing
upward risks condensation moisture entering the transmitter housing, which could
damage the transmitter.
Following are examples of possible orientations for the transmitter.
Preferred orientation Alternate orientations
□Mount the meter in a location and orientation that satisfies the following conditions:
—Allows sufficient clearance to open the transmitter housing cover. Install with 8 in
(203 mm) to 10 in (254 mm) clearance at the wiring access points.
Installation Manual Planning
MMI-20029969 February 2020
Installation Manual 7

—Provides clear access for installing cabling to the transmitter.
—Provides clear access to all wiring terminals for troubleshooting.
2.2 Additional considerations for retrofitting
existing installations
□The transmitter installation may require 3 in (76 mm) to 6 in (152 mm) of additional
wiring for the input/output and power connections. This length would be in addition to
the currently installed wiring. Confirm you have the additional wiring necessary for the
new installation.
□Before removing the existing transmitter, be sure to record the configuration data for
the currently installed transmitter. At initial startup of the newly installed transmitter,
you will be prompted to configure the meter via a guided setup.
Record the following information (if applicable):
Variable Setting
Tag
Mass flow units
Volume flow units
Density units
Temperature units
Calibration parameters (for 9-wire installations only)
Flow calibration factor FCF (Flow Cal or Flow Calibration Factor):
Density calibration factors —D1:
—D2:
—K1:
—K2:
—TC:
—FD:
Function block settings
Channel assignment
L_Type
XD_scale (engineering units
assignment)
2.3 Power requirements
Self-switching AC/DC input, automatically recognizes supply voltage:
•85 to 240 VAC, 50/60 Hz, 6 watts typical, 11 watts maximum
Planning Installation Manual
February 2020 MMI-20029969
8 Micro Motion 5700 transmitters for FOUNDATION Fieldbus

•18 to 100 VDC, 6 watts typical, 11 watts maximum
Note
For DC power:
•Power requirements assume a single transmitter per cable.
•At startup, the power source must provide a minimum of 1.5 amps of short-term
current per transmitter and not pull voltage below 18 VDC.
•Length and conductor diameter of the power cable must be sized to provide 18 VDC
minimum at the power terminals, at a load current of 0.7 amps.
Cable sizing formula
M = 18V + (R x L x 0.5A)
•M: minimum supply voltage
•R: cable resistance (in Ω/ft)
•L: cable length (in ft)
Typical power cable resistance at 68 °F (20.0 °C)
Wire gauge Resistance
14 AWG 0.0050 Ω/ft
16 AWG 0.0080 Ω/ft
18 AWG 0.0128 Ω/ft
20 AWG 0.0204 Ω/ft
2.5 mm20.0136 Ω/m
1.5 mm20.0228 Ω/m
1.0 mm20.0340 Ω/m
0.75 mm20.0460 Ω/m
0.50 mm20.0680 Ω/m
2.3.1 Maximum cable lengths between sensor and transmitter
The maximum cable length between the sensor and transmitter that are separately
installed is determined by cable type.
Cable type Wire gauge Maximum length
Micro Motion 4-wire remote
mount
Not applicable •1,000 ft (305 m) without
Ex-approval
•500 ft (152 m) with IIC
rated sensors
•1,000 ft (305 m) with IIB
rated sensors
Micro Motion 9-wire remote
mount
Not applicable 60 ft (18 m)
Installation Manual Planning
MMI-20029969 February 2020
Installation Manual 9

Cable type Wire gauge Maximum length
User-supplied 4-wire VDC 22 AWG (0.326 mm²) 300 ft (91 m)
VDC 20 AWG (0.518 mm²) 500 ft (152 m)
VDC 18 AWG (0.823 mm²) 1,000 ft (305 m)
RS-485 22 AWG (0.326 mm²)
or larger
1,000 ft (305 m)
Planning Installation Manual
February 2020 MMI-20029969
10 Micro Motion 5700 transmitters for FOUNDATION Fieldbus

3 Mounting and sensor wiring
3.1 Mounting and sensor wiring for integral-
mount transmitters
There are no separate mounting requirements for integral transmitters, and no need to
connect wiring between the transmitter and the sensor.
3.2 Mounting transmitters
There are two options available for mounting transmitters:
•Mount the transmitter to a wall or flat surface.
•Mount the transmitter to an instrument pole.
3.2.1 Mounting the transmitter to a wall or flat surface
Prerequisites
•Micro Motion recommends 5/16-18 (8 mm–1.25) fasteners that can withstand the
process environment. Micro Motion does not supply bolts or nuts as part of the
standard offering (general purpose bolts and nuts are available as an option).
•Ensure that the surface is flat and rigid, does not vibrate, or move excessively.
•Confirm that you have the necessary tools, and the mounting kit shipped with the
transmitter.
Procedure
1. Attach the mounting bracket to the transmitter and tighten the screws to 80 in lbf
(9.04 N m) to 90 in lbf (10.17 N m).
Installation Manual Mounting and sensor wiring
MMI-20029969 February 2020
Installation Manual 11

Figure 3-1: Mounting bracket to an aluminum transmitter
Figure 3-2: Mounting bracket to a stainless steel transmitter
2. For wall-mount installations, secure the mounting bracket to the prepared surface.
Mounting and sensor wiring Installation Manual
February 2020 MMI-20029969
12 Micro Motion 5700 transmitters for FOUNDATION Fieldbus

Figure 3-3: Wall-mounting bracket and dimensions for an aluminum
transmitter
A. 2.8 in (71 mm)
B. 2.8 in (71 mm)
Figure 3-4: Wall-mounting bracket and dimensions for a stainless steel
transmitter
A. 7.51 in (190.8 mm)
B. 3.67 in (93.2 mm)
Installation Manual Mounting and sensor wiring
MMI-20029969 February 2020
Installation Manual 13

3. For aluminum transmitters, place and attach the transmitter-mounting bracket to
the mounting bracket secured to the wall or instrument pole.
Figure 3-5: Attaching and securing an aluminum transmitter to the mounting
bracket
Tip
To ensure the mounting bracket holes are aligned, insert all attachment bolts into
place before tightening.
3.2.2 Mount the transmitter to a pole
Prerequisites
•Ensure that the instrument pole extends at least 12 in (305 mm) from a rigid base and
is no more than 2 in (51 mm) in diameter.
•Confirm that you have the necessary tools, and the instrument-pole mounting kit
shipped with the transmitter.
Procedure
For pole-mount installations, attach the U-bolt mounting piece to the instrument pole.
Mounting and sensor wiring Installation Manual
February 2020 MMI-20029969
14 Micro Motion 5700 transmitters for FOUNDATION Fieldbus

Figure 3-6: Pole-mounting bracket attachment for an aluminum transmitter
Figure 3-7: Pole-mounting bracket attachment for a stainless steel transmitter
3.3 Wire a remote-mount transmitter to the
sensor
Use this procedure to wire a 4-wire or 9-wire remote-mount transmitter to the sensor.
Prerequisites
•Prepare the 4-wire cable as described in the sensor documentation.
Installation Manual Mounting and sensor wiring
MMI-20029969 February 2020
Installation Manual 15

•Prepare the 9-wire cable as described in the Micro Motion 9-Wire Flowmeter Cable
Preparation and Installation Guide.
•Connect the cable to the sensor-mounted core processor or junction box as described
in the sensor documentation. You can access all product documentation on the
documentation DVD shipped with the product or at www.emerson.com.
Procedure
1. Remove the transmitter-to-sensor wiring compartment cover to reveal the terminal
connections.
Figure 3-8: Removal of the transmitter-to-sensor wiring compartment cover
2. Feed the sensor wiring cable into the transmitter wiring compartment.
Figure 3-9: Sensor wiring feedthrough
3. Connect the sensor wires to the appropriate terminals.
Mounting and sensor wiring Installation Manual
February 2020 MMI-20029969
16 Micro Motion 5700 transmitters for FOUNDATION Fieldbus

Important
Terminate the 4-wire cable drain wires only at the sensor/core processor end of the
cable. See the sensor installation manual for more detail. Do not connect the 4-wire
cable drain wires to the ground screw located inside the 5700 junction box.
•See Figure 3-10 for 4-wire terminal connections.
•See Figure 3-11 for 9-wire terminal connections.
Figure 3-10: 4-wire transmitter-to-sensor wiring connections
Figure 3-11: 9-wire transmitter-to-sensor wiring connections
Note
Connect the 4 drain wires in the 9-wire cable to the ground screw located inside the
junction box.
4. Replace the transmitter-to-sensor wiring compartment cover and tighten the
screws to 14 in lbf (1.58 N m) to 15 in lbf (1.69 N m).
Installation Manual Mounting and sensor wiring
MMI-20029969 February 2020
Installation Manual 17

3.4 Ground the meter components
In 4-wire or 9-wire remote installations, the transmitter and sensor are grounded
separately.
Prerequisites
NOTICE
Improper grounding could cause inaccurate measurements or meter failure.
WARNING
Failure to comply with requirements for intrinsic safety in a hazardous area could result
in an explosion causing death or serious injury.
Note
For hazardous area installations in Europe, refer to standard EN 60079-14 or national
standards.
If national standards are not in effect, adhere to the following guidelines for grounding:
•Use copper wire, 14 AWG (2.08 mm²) or larger wire size.
•Keep all ground leads as short as possible, less than 1 Ω impedance.
•Connect ground leads directly to earth, or follow plant standards.
Procedure
1. Ground the sensor according to the instructions in the sensor documentation.
2. Ground the transmitter according to applicable local standards, using the
transmitter’s internal or external ground screw.
•The earth ground terminal is located inside the power wiring compartment.
•The external ground screw is located on the side of the transmitter located
below the transmitter tag.
Mounting and sensor wiring Installation Manual
February 2020 MMI-20029969
18 Micro Motion 5700 transmitters for FOUNDATION Fieldbus

3.5 Rotate the transmitter on the sensor (optional)
In integral installations, you can rotate the transmitter on the sensor up to 360º in 45º
increments.
Procedure
1. Using a 4 mm hex key, loosen and remove the clamp securing the transmitter head
in place.
Figure 3-12: Removal of the sensor clamp
2. Gently lift the transmitter straight up, and rotate the transmitter to the desired
position.
You can rotate the transmitter to any of the eight positions, but a stop exists that
will not allow a full 360° rotation.
Figure 3-13: Rotation of the transmitter head
3. Gently lower the transmitter onto the base, confirming that the transmitter is in a
locked position.
Installation Manual Mounting and sensor wiring
MMI-20029969 February 2020
Installation Manual 19

4. Replace the clamp in its original position and tighten the cap screw. Torque to 28 in
lbf (3.16 N m) to 30 in lbf (3.39 N m).
Figure 3-14: Re-attachment of the sensor clamp
3.6 Rotate the user interface on the transmitter
(optional)
The user interface on the transmitter electronics module can be rotated 90°, 180°, or 270°
from the original position.
Figure 3-15: Display components
A. Transmitter housing
B. Sub-bezel
C. Display module
D. Display screws
E. End-cap clamp
F. Cap screw
G. Display cover
Mounting and sensor wiring Installation Manual
February 2020 MMI-20029969
20 Micro Motion 5700 transmitters for FOUNDATION Fieldbus