TRASSIR TR-D3123WDIR2 User manual

2MP Indoor Dome IP camera
TR-D3123WDIR2
Note: read user manual before using
Website: www.trassir.com
For any inquiry: [e-mail]
TR-D3123WDIR2
1/2.7" CMOS 2.1MP
FullHD (1920x1080)
Mechanical ICR
up to 25 m
PoE (802.3af) / 12V DC
FullHD@40fps (WDR off)
FullHD@25fps (WDR on)
Vari-focal 2.7-13.5 mm
Video compression Н.264 / H.265
8Mbps
0.003Lux (F1.3)
0Lux (F1.3, IR on)
WDR Real WDR (120dB)
5.5 W
330
-10°C … +50°C
Ø112 x 98
Day/Night Mode
Frame rate
Lens
Bitrate
Model
Resolution
Dimensions (mm)
Image sensor
Working temperature
Sensitivity
Power consumption
IR range
Net weight (g)
Power supply
Audio 2-way
Specification
Local storage USB 2.0 (USBHDD up to 128Gb)
12V
PoE
Cut
IR
3D-NR
Technical support
www: helpdesk.trassir.com
mail: helpd[email protected]
Data ___________________________ Stamp ___________________________
Here is the confirmation form for warranty assurance
2MP
VARIO
IP camera
User manual
Mounting kit
Camera Package
1 pc
1 pc
1 pc

Connecting
To get started with TRASSIR IP camera you are required to have a PC
connected to the local network with Windows installed and Internet
Explorer version 8 or higher.
1. Connect IP camera to the network.
2. When the camera is connected through a switch which doesn't
support PoE, connect 12V AC adapter to power jack.
Dimensions
Manual setting of network parameters.
IP camera and PC should be in one local network to connect to each
other. In this case IP address of a camera, PC or any other devices
shouldn't match each other.
IP camera has the following default settings:
- IP address: 192.168.1.188
- Subnet mask: 255.255.0.0
- Gateway: 192.168.1.1
- HTTP-port: 80
- username: admin
- password: admin
Example of network settings for PC to connect to IP camera:
- IP address: 192.168.1.10;
- Subnet mask: 255.255.0.0.
There are 3 options to set up your camera:
1. Change IP address of a camera manually.
Start your browser, connect to IP camera and enter your
username and password. Choose appropriate menu item and change
network settings of IP camera.
2. Set IP address of a camera using fast configuration utility which could
be downloaded from www.trassir.com.
3. Change IP camera settings using TRASSIR professional software.
Find detailed instruction on camera settings in user manual which could
be downloaded from our website www.trassir.com.
Notes:
Power supply should meet the requirements: output voltage, current,
polarities and working temperature. Pay attention that you have
lightning conductor while using IP camera during a storm or plug off
power connector.
Pay attention to temperature requirements of IP-camera. Avoid of using
IP camera in high or low temperatures.
Don't install your IP camera near heaters.
Don't direct camera lens to the sun or bright object. It could harm your
image sensor.
Introduction
Congratulations with purchasing of IP camera TR-D3123WDIR2.
Please read User Manual before using a camera.
Key features
• Support codec H.265
• Wide Dynamic Range (Real WDR 120dB)
• Automatic Day/Night Mode
• 2.7-13.5 mm vari-focal lens
• Mechanical IR cut filter
• Support of 2 video streams
• Audio in/out: 1 in / 1out, built-in microphone
• Local recording on Extended USBHDD* (USB 2.0 up to 128Gb)
• Power supply 12V DC or PoE
_____________
* USBHDD is not included into camera package
498-5.3.18