Travis Industries 564 HO User manual

564 HO Fireplace
Listed by
AS 4553-2008
GMK10022
IAPMO-R&T OCEANA
Operation - Maintenance
WARNING: If the information in these instructions is not followed exactly, a fire or
explosion may result causing property damage, personal injury or loss of
life.
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Immediately call gas supplier from a neighbor's phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier, call the fire department.
- Installation and service must be performed by a qualified installer, service agency or the gas
supplier.
This appliance may be installed in
an aftermarket permanently
located, manufactured home (USA
only) or mobile home, where not
prohibited by local codes.
This appliance is only for use
with the type(s) of gas indicated
on the rating plate. A conversion
kit is supplied with the appliance.
Owner's Manual
Copyright 2012, T.I. $10.00 100-01328 4121206
Dragon Wholesaling Pty. Ltd.
Unit 2, 16 Lexington Drive
Bella Vista NSW 2153
Australia

2 Introduction
© Travis Industries 4121206 100-01328
Introduction
We welcome you as a new owner of a 564 HO gas fireplace. This manual details operation and
maintenance of this fireplace. Please familiarize yourself with the Owner's Manual before operating your
heater and save the manual for future reference.
Important Information
No other 564 HO gas fireplace has the same serial
number as yours. The serial number is on the listing
label that is chained to the gas control valve. This
serial number may be needed in case you require
service.
Model: 564 HO GSR Fireplace
Serial Number:
Purchase Date:
Purchased From:
Register your warranty online at:
lopi.com.au
Or, mail your warranty card to:
Dragon Wholesaling Pty. Ltd.
Unit 2, 16 Lexington Drive
Bella Vista NSW 2153
Australia
Save Your Bill of Sale.
To receive full warranty coverage, you will
need to show evidence of the date you
purchased your heater. Do not mail your Bill
of Sale to us.
We suggest that you attach your Bill of Sale
to this page so that you will have all the
information you need in one place should the
need for service or information occur.
Installation Warnings
Installation requirements are printed in the 564 HO GSR Installation Manual (part #
100-01327). All requirements in the installation manual must be met.
Failure to follow all of the requirements may result in property damage, bodily injury,
or even death.
This heater must be installed by a qualified installer who has gone through a training
program for the installation of direct vent gas appliances.
This appliance must be installed in accordance with all local codes, if any; if not,
follow ANSI Z223.1 and NFPA 54(88).
In Manufactured or Mobile Homes must conform with Manufactured Home
Construction and Safety Standard, Title 24 CFR, Part 3280, or, when such a standard
is not applicable, the Standard for Manufactured Home Installations, ANSI/NCSBCS
A225.1. This appliance may be installed in Manufactured Housing only after the
home is site located.
The fireplace is designed to operate on natural gas, or propane (LP).
All exhaust gases must be vented outside the structure of the living-area.
Combustion air is drawn from outside the living-area structure.
Notify your insurance company before hooking up this fireplace.

Introduction 3
© Travis Industries 4121206 100-01328
Table of Contents

Introduction ...................................................2
Important Information...................................2
Installation Warnings....................................2
Table of Contents..........................................3
Features .........................................................3
Heating Specifications..................................3
Before You Begin..........................................6
Remote Set-Up...............................................6
Verify the Insert is plugged in..............................6
Synchronize the Transmitter to the Receiver ......6
Starting the Fireplace for the First Time.....6
Direct Operation............................................7
Accent Light...................................................7
Adjusting the Blower Speed ........................8
Continuous Pilot / GreenSmart™ Pilot
Switch.............................................................8
Remote Operation.........................................9
Changing the Display to Celcius (C)....................9
Display Overview ................................................9
Listen for the “Beep”............................................9
Manual On-Off / Smart Thermostat / Standard
Thermostat........................................................10
Mode Controls (Flame, Comfort Control) ..........11
Flame Height........................................................ 11
Comfort Control (rear burner)............................... 11
Normal Operating Sounds..........................12
Normal Operating Odors ............................12
Low Battery Indicator .................................13
Transmitter Batteries.........................................13
Receiver Batteries.............................................13
Child Proof Feature.....................................13
Power Outages............................................13
Maintaining Your Fireplace's Appearance13
Battery Replacement..................................14
Accent Light Replacement.........................15
Lower Bulbs ......................................................15
Upper Bulb........................................................15
Yearly Service Procedure...........................17
Grill Installation and Removal ...................18
Face Installation and Removal ..................19
Glass Frame Removal and Installation.....20
Glass Frame Removal and Installation
(continued)...................................................21
Log Set Installation.....................................22
Log Set Overview..............................................22
Glass Cleaning..................................................22
Troubleshooting Table...............................23
Wiring Diagrams .........................................24
Replacement Parts List..............................24
CONDITIONS & EXCLUSIONS ...................25
IF WARRANTY SERVICE IS NEEDED: ......25
Index .................................................................26
Features
Works During Power Outages (battery backup)
GreenSmart™ Thermostat / Remote Control
Realistic "Wood Fire" Look
Standard Blowers for Effective Heat Distribution
Built-In Accent Light (night light)
Built-In Control Panel Light
Standing or Intermittent (GreenSmart) Pilot
Convenient Operating Controls
Variable-Rate Heat Output
Low Maintenance
Heating Specifications
Natural Gas Propane
Approximate Heating Capacity (in square meters)* Up to 158 Up to 158
Maximum MJ Input Per Hour 35.0 35.0
* Heating capacity will vary with floor plan, insulation, and outside temperature.

4 Safety Precautions
© Travis Industries 4121206 100-01328
IF YOU SMELL GAS:
* Do not light any appliance
* Extinguish any open flame
* Do not touch any electrical switch or plug or unplug anything
* Open windows and vacate building
* Call gas supplier from neighbor's house, if not reached, call fire department
This unit must be installed by a qualified installer to prevent the possibility of an explosion.
Your dealer will know the requirements in your area and can inform you of those people
considered qualified. The room heater should be inspected and cleaned before use and at
least annually by a qualified service person. More frequent cleaning may be required due
to excessive lint from carpeting, bedding material, etc.
The instructions in this manual must be strictly adhered to. Do not use makeshift methods
or compromise in the installation. Improper installation will void the warranty and safety
listing.
This heater is either approved for natural gas (NG) or for propane (LP). Burning
the incorrect fuel will void the warranty and safety listing and may cause an
extreme safety hazard. Direct questions about the type of fuel used to your dealer.
Check for a label on the flame adjust knob on the gas control valve (this is the best
place to check). You may also check for a label on the gas control valve body.
Contact your local building
officials to obtain a permit and
information on any installation
restrictions or inspection
requirements in your area.
Notify your insurance company
of this heater as well.
If the flame becomes sooty, dark
orange in color, or extremely tall,
do not operate the heater. Call
your dealer and arrange for
proper servicing.
It is imperative that control
compartments, screens, or
circulating air passageways of
the heater be kept clean and
free of obstructions. These
areas provide the air necessary
for safe operation.
Do not operate the heater if it is
not operating properly in any
fashion or if you are uncertain.
Call your dealer for a full
explanation of your heater and
what to expect.
Do not store or use gasoline or
other flammable liquids in the
vicinity of this heater.
Do not operate if any portion of
the heater was submerged in
water or if any corrosion occurs.
Immediately call a qualified
service technician to inspect the
appliance and to replace any part
of the control system and any
gas control that has been under
water.
Ok
?
Gas









Safety Precautions 5
© Travis Industries 4121206 100-01328
Do not place clothing or other
flammable items on or near the
heater. Because this heater can
be controlled by a thermostat
there is a possibility of the
heater turning on and igniting
any items placed on or near it.
Light the heater using the built-in
igniter. Do not use matches or
any other external device to light
your heater.
Allow the heater to cool before
carrying out any maintenance or
cleaning.
The viewing glass should be
opened only for conducting
service. Do not operate with
cracked, broken, or removed
glass.
Any safety screen or guard
removed for servicing must be
replaced prior to operating the
heater.
Never remove, replace, modify or
substitute any part of the heater
unless instructions are given in
this manual. All other work must
be done by a trained technician.
Don't modify or replace orifices.
Operate the heater according to
the instructions included in this
manual.
If the main burners do not start
correctly turn the gas off at the
gas control valve and call your
dealer for service.
Instruct everyone in the house
how to shut gas off to the
appliance and at the gas main
shutoff valve. The gas main
shutoff valve is usually next to
the gas meter or propane tank
and requires a wrench to shut off.
This unit is not for use with solid
fuel
Do not place anything inside the
firebox (except the included fiber
logs).
If the fiber logs become
damaged, replace with Travis
Industries log set.
Do not throw this manual away.
This manual has important
operating and maintenance
instructions that you will need at
a later time. Always follow the
instructions in this manual.
Children and adults should be
alerted to the hazards of high
surface temperature and should
stay away to avoid burns or
clothing ignition. Young children
should be supervised when they
are in the same room as the
heater.
Dragon Wholesaling grants no
warranty, implied or stated, for
the installation or maintenance
of your heater, and assumes
no responsibility of any
consequential damage(s).









This
Manual

6 Operation
© Travis Industries 4121206 100-01328
Before You Begin
Read this entire manual before you use your new fireplace (especially the section "Safety
Precautions" on pages 4 & 5). Failure to follow the instructions may result in property damage, bodily
injury, or even death.
Remote Set-Up
Verify the Insert is plugged in
The insert should be plugged in before synchronizing the remote.
Synchronize the Transmitter to the Receiver
The transmitter will need to be synchronized to the receiver before the remote will work correctly.
Synchronizing is done in the following two steps below (see Figure 1):
a) Press the PRG (Program) button on the receiver using a paperclip or equivalent device (receiver
will beep 3 times).
b) Press the “ON” button on the transmitter (receiver will beep 4 times).
Figure 1
NOTE: If power is cut off to the receiver for an extended period of time, you may need to re-synchronize
the remote.
Starting the Fireplace for the First Time
Burn the heater at a high setting with the blower off for an extended period (up to 48 hours). This will
cure the painted surfaces. Fumes from the paint curing and oil burning off the steel will occur. This
is normal. We recommend opening a window to vent the room.
Condensation may appear on the glass each time you start the fireplace - this is normal.
Blue Flames will occur on the fireplace when it first comes on. After fifteen minutes the flames will
turn a more realistic yellow and orange color.
Certain installations use a remote, thermostat, or wall switch to turn the fireplace on and off. If this is
the case, leave the ON/OFF switch "ON".
Verify the power backup and control light batteries are installed (see page 14).
Display Fahrenheit or Celsius
With the system in the “OFF” position, press both the MODE and THERMOSTAT buttons
simultaneously to toggle between Fahrenheit (F) and Celsius (C).
Figure 2
°F
====
"Beep"
"Beep"
"Beep"
“Beep”
"Beep"
"Beep"
"Beep"
F
C
F

Operation 7
© Travis Industries 4121206 100-01328
Direct Operation
The fireplace may be directly operated from the receiver. The three positions are below (see Figure 3):
ON – Burner turns on (regardless of transmitter settings).
OFF – Burner turns off (regardless of transmitter settings).
REMOTE – Burner is controlled by the transmitter.
Figure 3
NOTE: When the receiver switch is turned to ON or OFF, the mode settings (Flame Height, Comfort
Control) will remain in the same state as before the switch was moved (i.e.: the receiver “remembers” the
last setting). If you wish to adjust the mode settings use the transmitter mode button to adjust the settings
(see “Mode Controls” on page 11). The thermostat and burner on/off operating functions will not work on
the transmitter.
Accent Light
This fireplace has a built-in accent light that may be turned on and off and dimmed to your preference.
Turn the knob to achieve the desired light output.
ON
REMOTE
OFF PRG
ACCENT LIGHT
OFF
HIGH
LOW
OFF LOW HIGH

8 Operation
© Travis Industries 4121206 100-01328
Adjusting the Blower Speed
The blower helps transfer heat from the heater into the room. It will not turn on until the heater is up to
temperature (approximately 15 minutes after starting). See the illustration below for instructions on
adjusting the blower speed.
NOTE: With the rear burner off (comfort control), the heater may not become hot enough for the
blower to turn on.
Continuous Pilot / GreenSmart™ Pilot Switch
This fireplace may run with the pilot continuously running or in GreenSmart (intermittent) mode. For most
homeowners, the GreenSmart mode is preferred (this saves fuel, doesn’t give off un-needed heat).
However, in some situations the homeowner may prefer to switch the fireplace to continuous pilot. The
most typical reasons for switching to continuous pilot are:
Very Cold Conditions – in very cold conditions you may notice that the burner does not light quickly,
and the flames lift off the burner. If this is situation, we recommend you switch to continuous pilot.
This will create a slight draft in the vent, allowing for the burner to light quickly and draft correctly.
Excessive Condensation on Glass After Startup – certain installations may encounter excessive
fogging on the window after stuartup (not just the first time the fireplace was started). This is an
aesthetic condition that may be remedied by switching the fireplace to continuous pilot.
Cold Glass or Fireplace Front – in very cold conditions you may notice that the fireplace front and
glass become very cold. To remedy this, switch the fireplace to continuous pilot.
Frequent On / Off Operation – if you are frequently turning the fireplace on and off, you may wish to
leave it in continuous pilot. This allows the burner to turn on more quickly, without pilot ignition delay.
BLOWER
OFF
HIGH
LOW
CONTINUOUS
PILOT
GREEN SMART
PILOT

Operation 9
© Travis Industries 4121206 100-01328
Remote Operation
Once the receiver is switched to “REMOTE” the transmitter operates the fireplace. Once you understand
how the transmitter works, you will be able to operate your fireplace quickly and easily.
Changing the Display to Celcius (C)
With the remote off, press the thermostat and mode button simultaneously. This will toggle between
Fahrenheit and Celcius.
Display Overview
The transmitter display has four main sections (see Figure 4).
Figure 4
Listen for the “Beep”
Each time you press a button on the transmitter that controls the fireplace, a “beep” will come from the
fireplace. When you change thermostat target settings the fireplace will not beep.
NOTE: When the receiver batteries start to get low, the receiver will beep intermittently. When the
batteries are nearly depleted, the receiver will no longer beep. See “Receiver Batteries” on page 13).
ON
MAX
Thermostat Display
Room Temperature Display
Read-Out (Thermostat Setting, Function, etc.)
Mode Display (Flame Height, Comfort Control)
C

10 Operation
© Travis Industries 4121206 100-01328
Manual On-Off / Smart Thermostat / Standard Thermostat
Use the thermostat button to cycle through the three thermostat settings (see Figure 5).
Figure 5
MANUAL ON/OFF – The burner will turn on and off using the remote (see Figure 6). Press the
On/Off button to control the burner. When off, the display will only show the current temperature.
Figure 6
SMART THERMOSTAT – While in smart thermostat, the transmitter will control the burner to
achieve the target temperature (see Figure 7 below). Flame height will be adjusted up or down to
allow operation without turning the burner on and off (also called “smart modulation). To adjust
the target temperature, press the up and down buttons until a suitable temperature is achieved.
Figure 7
STANDARD THERMOSTAT - While in standard thermostat setting, the transmitter will turn the
burner on and off to achieve the target temperature (see Figure 8 below). To adjust the target
temperature, press the up and down buttons until a suitable temperature is achieved.
Figure 8
NOTE: if the transmitter batteries go dead while in thermostat setting (standard or smart), the appliance
will shut off after approximately 24 hours.
OFF
ON SMART
ON
Look here for the
thermostat setting. Press the thermostat button to cycle
through the thermostat settings.
C
OFF
When in manual setting, the
word “OFF” will appear here.
MAX
C
When in smart thermostat
setting, the word “SMART”
will appear here.
This is the target temperature
on the read-out. Use the up
or down buttons to adjust the
target temperature.
SMART
C
ON
When in standard thermostat
setting, the word “ON” will
appear here.
This is the target temperature
on the read-out. Use the up
or down buttons to adjust the
target temperature.
C

Operation 11
© Travis Industries 4121206 100-01328
Mode Controls (Flame, Comfort Control)
Use the mode button to cycle through the two mode controls (see Figure 9 below).
Figure 9
Flame Height
Flame height may be controlled using the up and down buttons when in Flame Height Mode (see Figure
10 below). The center display will display the 7 settings, from “OFF” to “HI” for full on.
NOTE: Flame height may not be adjusted if operating in Smart Thermostat setting.
Figure 10
Comfort Control (rear burner)
The comfort control (rear burner) may be turned on and off using the up and down buttons when in
Comfort Control Mode (see Figure 11). The center display will display either “ON” or “OFF”.
Figure 11
Flame
Height
OFF
Look here for
mode controls.
Press the mode button to cycle through the mode settings.
Comfort
Control
MAX
C
OFF
When in flame height
mode, this icon will
appear darkened.
This is the flame height read-
out. Use the up or down
buttons to adjust the flame
height (7 settings).
High
Medium
Off
MAX
C
OFF
When in comfort
control mode, this
icon will appear
darkened.
This is the comfort control
read-out. Use the up button
to turn on, down button to turn
off (2 settings).
On
Off
C

12 Operation
© Travis Industries 4121206 100-01328
Normal Operating Sounds
Normal Operating Odors
This appliance has several areas that reach high temperatures. Dust or other particles on these areas
may burn and create an odor. This is normal during start-up. You may notice the smell is more acute if
the appliance was left idle for a long period.
Blowers
This heater has optional blowers to push
heated air into the room. You will hear the
sound of air movement that increases as
the speed is increased.
Extinction Pops
It is not unusual, especially on Propane
(LP) appliances, to experience a "pop"
when the burner is shut off.
Gas Control Valve
As the gas control valve is turned
on and off you will hear a dull
clicking sound. This is the valve
opening up and shutting down.
Blower Snap Disk
This part can produce a
clicking sound as it turns
the blower on and off.
The appliance may creak with change of
temperature -- THIS IS NORMAL.
Pilot Assembly
The pilot flame will make a clicking
sound when starting up. If left on, it
will make a slight whisper sound.
GreenSmart Receiver
The optional GreenSmart receiver will
beep when receiving commands from the
GreenSmart remote.
DC Converter
This device makes a light humm that
is audible in close proximity.

Maintenance 13
© Travis Industries 4121206 100-01328
Low Battery Indicator
Transmitter Batteries
The transmitter has a battery-level indicator. When it indicates low battery voltage (see below), install
three new AAA alkaline batteries into the transmitter (see “Battery Replacement” on page 14).
Figure 12
Receiver Batteries
The receiver will “beep” periodically when the receiver batteries go low. Install four new AA alkaline batteries
into the receiver when this occurs (see “Battery Replacement” on page 14). In applications where the
appliance is required to provide heat, we recommend replacing the batteries before each heating season.
Child Proof Feature
The child proof feature disables the control buttons, preventing un-wanted use of the remote.
Press both the MODE and UP buttons simultaneously to turn this feature on and off (see below).
HINT: This feature is especially useful while using the thermostat setting.
Figure 13
Power Outages
The remote will work if household current (AC power) is disconnected. The batteries inside the receiver
will continue to power the heater but the accent light and blower will not operate.
Maintaining Your Fireplace's Appearance
Fingerprints or other marks left on the optional plated surface may become etched in place if they are not
wiped clean prior to turning the fireplace on. Clean the plated surface with denatured alcohol and a soft
cloth (with the fireplace cool). Other cleaners may leave a film that may become etched into the surface.
ON
Low Battery Indicator
MAX
C
ON
Child Proof Indicator
MAX
C

14 Maintenance
© Travis Industries 4121206 100-01328
Battery Replacement
1. Install the four AA batteries (see illustration below). The AA batteries act as a power backup in case the
household (AC) power goes out and are required for operation. Install three AAA batteries into the remote (see
illustration below). Synchronize the transmitter to the IFC (see page 6).
°F
AAA Battery
AAA Battery
AAA Battery
AA Battery
AA Battery
AA Battery
AA Battery

Maintenance 15
© Travis Industries 4121206 100-01328
Accent Light Replacement
Accent lights are included in your fireplace to provide additional lighting. These bulbs will burn out over
time. To replace, follow the directions below:
Shut off gas to the fireplace and let it cool for 15 minutes.
Turn off electricity to the fireplace (disable the breaker).
Remove the glass (see page 20) and logs (see instructions included with logs).
Replace the halogen bulbs with the following bulbs:
35 Watt 240 Volt T4 Halogen Bulb (G6.35 Base)
Lower Bulbs
Located behind the logs on the EmberFyre and DancingFyre Burners.
Located below the media tray (firebox floor) on the DiamondFyre Burner.
Remove the bulb from the socket as shown above.
(NOTE: .Take care to not touch the bulb with your fingers – use foam packing or paper towel to hold the bulb):
Upper Bulb
1. Remove the exhaust manifold from the roof of the fireback. The 2 rear screws are in slots, and do not
need to be removed. Remove the 2 front screws from the exhaust manifold, then tilt the manifold
down and slide it forward to remove.

16 Maintenance
© Travis Industries 4121206 100-01328
2. Remove the accent light cover plate from the roof of the firebox. Remove the outer 8 screws, not the
inner 4 screws.
NOTE: When replacing this plate, position the glass to the rear. Make sure the gasket seals tightly
against the firebox ceiling.
3. Pull down the upper accent light enclosure from the roof of the firebox, as shown below. Note the 3
screws holding the bulb assembly in place.
4. Remove the 3 screws holding the bulb assembly in the accent light enclosure. Remove the bulb
assembly from the enclosure.

Maintenance 17
© Travis Industries 4121206 100-01328
5. Loosen the two screws nearest the bulb to disengage the bulb from the holder. Remove the bulb
from the holder. Replace the bulb, making sure not to touch the bulb with your fingers (grasp the bulb
with the bulb packaging or a paper towel). Tighten the screws until the bulb is secure (do not over-
tighten, this may damage the electrical contacts on the bulb).
6. Return the fireplace to the correct configuration.
Yearly Service Procedure
Failure to inspect and maintain the fireplace may lead to improper combustion and a potentially
dangerous situation. We recommend the following procedures be done by a qualified technician.
1. Turn the pilot flame to continuous. It should touch approximately 3/8" of the top of the flame sensor. If it does
not, contact your dealer for service.
2. Shut off gas to the fireplace and let it cool for 15 minutes. Remove the glass (see page 20).
3. Remove the log set (NOTE: The logs are very fragile — see page 22). If severely deteriorated, replace.
Check the logs for sooting. A small amount of soot along the bottom of the logs is normal. If excessive sooting
is found, the fireplace will require adjustment. Contact your dealer.
4. Inspect the burner and remove any debris.
•Make sure the burner is not warped, cracked, or damaged.
•Check the firebox and area around the pilot to make sure there is no warping or damage.
•If any problem is found, discontinue use and contact your dealer for service.
5. Replace the log set. Clean and replace the glass (see Glass Cleaning on page 22). If the glass is damaged,
replace. Make sure the gasket along the perimeter of the glass contacts the face of the firebox and forms an air-
tight seal. If it does not, re-align or replace the gasket to insure an air-tight seal.
6. Inspect the area behind the access door. Clean if necessary. Check the gas
control valve and the gas lines. If damage is found, discontinue use and contact
your dealer for service. Clean the air channels, ducts, and blower (if applicable).
7. Start the main burner. Inspect the main burner and pilot flame. After 15 minutes
the flames should be orange/yellow and not touch the top of the firebox. If the
pilot or main burners do not burn correctly, contact your dealer for service.
Monitor blower operation.
8. Remove any debris or vegetation near the vent termination. Contact your dealer
if any sooting or deterioration is found near the vent termination. Venting system
should be examined by a qualified agency.

18 Maintenance
© Travis Industries 4121206 100-01328
Grill Installation and Removal
Follow the directions below to install.
Hold the grill at an angle and insert the
lower s lot over the lower bushing on
the replace (both sides)
S wing the grill upwa rds to e nga ge the upper s lot. Y ou
will need to lift the grill s lightly to get it over the bus hing.
Once in place the grill is held in place by gravity.
Lower G rill Ins tallation
Hold the grill a t an angle and ins ert the lower
slot over the bushing on the fireplace (both
sides). You may need to press on the grill to
ge t the ta b ov er the bus hing ( this pre ve nts
the grill from a ccidentally falling o).
Bend the tab outward on
both sides. This is the
end-s top for the lower grill,
it allows the grill to s wing
forward.
S wing the grill upwards to engage
the upper s lot. Y ou will ne ed to lift
the grill s lightly to ge t it ove r the
bus hing. Once in place the grill is
held in place by gra vity.
NOTE : The upper grill is di cult to install the rst time - be
patient, after you ins tall it, you will know how it installs and it
will be much eas ier the s ec ond time.
SIDE VIEW
P os ition the grill
so the slots on
the grill align with
the mounting
studs.
You may need to
pus h in and
upwards on the
grill as it inserts.
T he grill, when
fully ins erted,
will slide down
and "click" into
place.
Upper G rill
Heat Shields
(on replace)
Mounting S tud
Upper G rill Ins tallation (L opi)
Upper Grill Installation

Maintenance 19
© Travis Industries 4121206 100-01328
Face Installation and Removal
Some fireplaces have a face that fits over the glass frame. The face can be removed following the
directions below.
Phillips
Screwdriver
Four screws hold the face
in place. The screws are
accessed through the
grills on the face.

20 Maintenance
© Travis Industries 4121206 100-01328
Glass Frame Removal and Installation
Warning: The appliance must be completely cool before removing the glass.
Warning: Do not strike or slam the glass.
a
b
Depending on the face being used, either:
1) Swing the access door down and remove the top grill, or
2) Remove the face by unscrewing it or lifting it off -- see
the instructions included with the face for details.
Open the 4 latches holding the glass frame in place,
starting with the bottom. Follow the instructions shown to the right.
Latch
Glass
Top o f
Firebox
Lift the glass frame up and
pull it forward to remove.
NOTE:
You may need to lift
the glass frame
while re-attaching.
Catch on
glass frame
Re-Attaching the Glass Frame:
1) Hang the glass frame on the firebox.
2) While holding the frame in place, attach the upper latches
(follow the instructions to the right in reverse).
3) Lift the glass frame slightly and attach the lower latches.
NOTE: Make sure the glass frame is fully in place -- it should
be flush with the front of the fireplace when installed correctly.