Travis Industries NSB-G3 User manual

with large pull-out
keyboard shelf and
locking storage cabinet

2
Keyboard Tray
K
Top Shelf
A
Keyboard Back Panel
C
Middle Shelf
F
Left Upper
Side Panel
B1
Upper Legs
D
Bottom Shelf
G
Right Cabinet Door
J1
Right Upper
Side Panel
B2
Lower Legs
E
Cabinet Side Panel
H
Left Cabinet Door
J2
Parts List // NBS-G3 // AV Cart
Missing or Damaged Parts?
For your convenience, contact the distributor
you purchased this product from
Rear Cabinet Panel
I
1x
1x
1x
1x
4x
1x
1x
4x
2x

3
Parts List (continued)
Step 1:Attach Upper Legs (D) to Top Shelf (A)
Tools Required
Hex Wrench (included)
Phillips Screwdriver (included)
Rubber Mallet (optional)
Part Description Qty
Z1 Square Head Bolt 24
Z2 Washer Base Lock Nut 24
Z3 Lock & Keys 1
Z4 Door Handle 2
Z5 Door Hinge 4
Z6 Caster 2
Z7 Locking Caster 2
Z8 Plastic Grommet 3
Z9 Keyboard Slide 2
Z11 CS Screw 32
Z1 Z2 Z3 Z4
Z5 Z6 Z7 Z8
Do not operate unless all screws are tight. To ensure
stability, proper function, and safety, every six months
check to make sure screws are tighten. Do not use
product if a part becomes missing, broken, damaged, or
worn. Wait until proper repairs have been made by your
dealer before continued operation
Flip the Top Shelf (1. A) on it’s back so
that the at side faces down
Position (1x) Upper Leg (2. D) at each
corner of Top Shelf (A)
Use (4x) Pan Head Screws (3. Z1) and
(4x) Washer Base Lock Nuts (Z2) to fasten
Upper Legs (D) to Top Shelf (A) where
notated (see illustration # 1).
Parts used in this step:
Top Shelf (A)
Upper Legs (D)
(4x) Pan Head Screws (Z1)
(4x) Washer Base Lock Nuts (Z2)
Illustration # 1
Z1
Z2
D
A
Z11
Z9

4
Step 2:Attach Upper Side Panels (B1, B2)
Step 3:Attach Keyboard Back Panel (C)
Slide Left Upper Side Panel (1. B1) and
Right Upper Side Panel (B2) onto the
left and right sides of Top Panel (A).
Make sure the at side of each side
panel faces inward, and hole pattern
matches image (see illustration # 2)
Use (4x) Pan Head Screws (2. Z1) and
(4x) Washer Base Lock Nuts (Z2) to fasten
Upper Side Panels (B1,B2) to Top Panel (A)
where notated (see illustration # 2).
Position Keyboard Back Panel1. (C) between Upper Side Panels
(B1,B2) near rear of cabinet
Secure the Keyboard Back Panel2. to the Upper Side Panels using
(4x) Pan Head Screws (Z1)
Parts used in this step:
Left Upper Side Panel (B1)
Right Upper Side Panel (B2)
(4x) Pan Head Screws (Z1)
(4x) Washer Base Lock Nuts (Z2)
Parts used in this step:
Keyboard Back Panel (C)
(4x) Pan Head Screws (Z1)
Illustration # 2
Illustration # 3
B1
B2
Z1
Z1
Z2
A
C
B2
B1

5
Step 5:Position Bottom Shelf (G) and Middle Shelf (F)
Step 4:Attach Keyboard Slides (Z9)
Position Bottom Shelf (1. G) onto
lower brackets of Lower Legs (E).
Position Middle Shelf (2. F) onto upper
brackets of Lower Legs (E).
Note: Do not
fasten screws
lower brackets
upper brackets
Disassemble Keyboard Slides1. into two pieces - base brackets
(Z9a) and rails (Z9b)
Attach base brackets to2. Keyboard Tray (K) using
(8x) CS Screws (Z11).
Set aside until nal step.
Attach rails to Upper Side3. Panels (B1,B2) using
(8x) CS Screws (Z11)
Parts used in this step:
Keyboard Slides (Z9)
Keyboard Tray (K)
(16x) CS Screws (Z11)
Parts used in this step:
Bottom Shelf (G)
Middle Shelf (F)
Lower Legs (E)
Once rails are attached, set
top unit aside until step 8
Illustration # 4
Illustration # 5
Z9b
Z9b
Z9a
Z9a K
B2
G
F
E
E
B1

6
Attach Door Hinges (1. Z5) to Right Cabinet Door (J1), and
Left Cabinet Door (J2) using (12x) CS Screws (Z11)
Disassemble the Door Lock (2. Z3) by removing the Lock
Screw (Z3-b), Lock Hasp (Z3-c), and Lock Clip (Z3-d)
from the Lock Cylinder (Z3-a).
Insert Lock Cylinder (3. Z3-a) into the lock hole on Right
Cabinet Door (J1). Attach Lock Clip to Lock Cylinder
(Z3-a), and secure Lock Hasp (Z3-c) to to Door Lock with
Lock Screw (Z3-b), as shown in illustration #6.
Step 7:Assemble Cabinet Doors (J1, J2)
Attach Door Hinges (1. Z5) to Right Cabinet Door (J1), and
Left Cabinet Door (J2) using (8x) CS Screws (Z11). Snap
Door Handles (Z4) into place (see illustration # 7)
Disassemble the Door Lock (2. Z3) by removing the Lock
Screw (Z3b), Lock Hasp (Z3c), and Lock Clip (Z3d) from
the Lock Cylinder (Z3a).
Parts used in this step:
Right Cabinet Door (J1)
Left Cabinet Door (J2)
Door Handles (Z4)
Door Hinges (Z5)
Door Lock (Z3)
(8x) CS Screws (Z11)
Step 6:Attach Cabinet Side Panels (H) and Rear Cabinet Panel (I)
Slide top of panels (1. H& I) into lip
of Middle Shelf (F)
Use (4x) Pan Head Screws (2. Z1)
and (4x) Washer Base Lock Nuts
(Z2) to fasten panels to Middle
Shelf (F) and Bottom Shelf (G) for
each side.
Parts used in this step:
Cabinet Side Panels (H)
Rear Cabinet Panel (I)
(16x) Pan Head Screws (Z1)
(16x) Washer Base Lock Nuts (Z2)
Illustration # 7
Illustration # 6
Z3b
Z3c
Z3d
Z3a
F
J2
Z4
Z5
Z5
Z11
Z11
J1
GI
H
H
Z1

7
Carefeully tilt the unit on its back or1. upside down (bottom side up).
Push Locking Casters (2. Z7) into the
bottom of the front legs, and the
Standard Casters (Z6) into the bottom
of the rear legs. Use a rubber mallet if
necessary.
Step 9:Insert Casters (Z6, Z7)
Step 8:Attach Cabinet Doors (J1, J2)
Parts used in this step:
Casters (Z6)
Locking Casters (Z7)
Parts used in this step:
Top Unit
Assembled Cabinet Doors (J1, J2)
(8x) Pan Head Screws (Z1)
(8x) CS Screws (Z11)
Slide top unit legs over base unit1. legs and line up screw holes at
desired height
Secure top unit to base unit using2. (8x) Pan Head Screws (Z1)
Attach Cabinet Doors (3. J1, J2) by
securing door hinges to base unit
using (8x) CS Screws (Z11)
Illustration # 8
Illustration # 9
J2
J1
Z11
Z7
Z6

8
Step 10:Insert Keyboard Tray (K)
Slide Keyboard Tray (K) into top unit
by sliding base brackets (Z9a) into
keyboard rails (Z9b).
Parts used in this step:
Keyboard Tray (K)
Illustration # 10
K
Z9a
Z9b