Traxxas PRO SCALE 1979 User manual

Installation
This kit contains the installation components necessary to adapt
the part #8039 Blazer LED Light Kit for full compatibility with the Pro Scale
Advanced Lighting Control system, part #6591 (part #8039 and 6591 sold
separately).
If the 8039 LED light kit has already been installed, it will be necessary to
remove the existing distribution block and mount in the body and install
the new Pro Scale Lighting Distribution Block (part #6593, included with part
#6591) using the new distribution block mount supplied with this kit. These
instructions assume the 8039 LED Light Kit has already been installed.
If you are installing the 8039 LED light kit for the first time, then follow the
instructions included with the LED light kit except use the Pro Scale Lighting
Distribution Block along with the mounting bracket supplied with this kit.
In either case above, you will also install the reverse lights harness supplied
with this kit alongside the tail light harness in the body. See the wiring
diagram on the reverse side for supplemental information.
1. Remove the 1.6x8mm button-head screws (2) to remove the installed
distribution block and mount from the vehicle body (Fig. A1).
2. Unplug the installed LED light wire harness connectors from the existing
distribution block.
3. Peel the backing from one side of the included adhesive foam tape and attach it to the flat surface on the back of the new distribution block mount. Do not
remove the backing from the other side of the tape yet (Fig. A2).
4. Install the new distribution block mount and secure with the 1.6x5mm button-head screws (2) from step 1 (Fig. A2).
5. Gently flex the body away from the distribution block mount and remove the backing from the other side of the foam tape. Press the body against the mount
to adhere it to the mount.
6. Insert the LEDs on the included reverse lights harness into the tail light assemblies. The LEDs should snap into place. Route the wiring harness alongside the
brake lights harness in the body (see Wiring Diagram on reverse side). Remove the installed zip ties. New zip ties are provided to secure the wires after the new
harness is added. Secure the wiring to the body in the locations provided. The zip ties do not need to be tight; allow some extra length for wire movement.
7. Plug all LED light wire harness connectors and the included double jumper into the ports on the Pro Scale Distribution Block. Match the color band and/or
letter indicator on the wire harnesses with the corresponding color/letter of each port on the distribution block (see chart below).
8. Use the included 2.6x8mm button-head screws (2) to secure the distribution block to the mount (Fig. A2).
TRAXXAS.com
Traxxas, 6250 Traxxas Way, McKinney, TX 75070, Phone: [phone], Fax: [phone], e-mail: [email protected]
HKC20013-R00 Rev 201020
Pro Scale®Lighting Installation Kit - 1979 Chevrolet®Blazer®
Covers Part #8082
Fig. A2
Kit contents:
• Distribution block mount (1)
• Reverse lights harness (1)
• Double jumper (1)
• 2.6x8mm button-head cap screws (2)
• Double-sided adhesive foam tape
• Zip ties (5)
Tools required:
• 1.5mm hex wrench
• 2.0mm hex wrench
1.6x8mm BCS
2.6x8mm BCS
Visitez Traxxas.com/manuals pour télécharger
les instructions dans votre langue.
Visite la página Traxxas.com/manuals para
descargar el instrucciones en su idioma.
Auf Traxxas.com/manuals, können Sie
anleitung in Ihrer Sprache downloaden.
Letter Color Description Function
A N/A Reverse light harness Back up light LEDs when vehicle is put in reverse
C Red Tail light harness Tail lights, brake lights, and rear integrated turn signal LEDs
F N/A Rear integrated turn signal
jumper
Install jumper when using rear integrated turn signals
(single red LED for tail, stop, and turn)
G White Headlight assembly harness Headlights and front marker light LEDs
H White Front turn signal harness Front turn signal light LEDs
PRO-SCALE
DISTRIBUTION
BLOCK
#XXXX
™
E
F
G
H
K
M
N
A
B
C
D
Part 6593
PRO SCALE® LIGHTING
DISTRIBUTION BLOCK
Wiring connectors for the lights are
labeled with numbers and/or colors.
Distribution Block LED Light Harness Ports
Fig. A1

XL-5 HV ESC
Rock
Light
Rock
Light
Motor
Chassis Wiring
(Top Down View)
To Motor Connector
Receiver Communication Cable
To Motor Connector
To ESC
To Receiver
Motor Sense
Connectors
From ESC
From ESC
From CH2
Lighting
Power
Module
Rock
Light
Rock
Light
Rock
Light
Rock
Light
Rock
Light
Rock
Light
To ESC
Lighting
Power
Module
FRONT
FRONT
Receiver Communication Cable
Black Wires to CH2
Blue Wire to CH1
Receiver
Body Wiring
(viewed from the underside of the body)
Side
Marker
Side
Marker
A
E
F
G
H
K
M
N
A
B
C
D
Part 6593
PRO SCALE® LIGHTING
DISTRIBUTION BLOCK
Reverse LightReverse Light
Tail Light / Turn Signal /
Brake Light
Tail Light / Turn Signal /
Brake Light
To MAXX Link
IN port on
Lighting Power
Module
Route wires under
battery tray
Route wires under
battery tray
For more information about
connecting additional chassis
mounted accessories (such as light bars
mounted on bumpers), please visit the
Support page on Traxxas.com
For more information about
connecting additional chassis
mounted accessories (such as light bars
mounted on bumpers), please visit the
Support page on Traxxas.com
Headlight /
Turn Signal
Headlight /
Turn Signal
From ESC
Actual mounting view.
Distribution Block face shown
in the diagram for clarity.
Optional MAXX Link
Cable Wiring
(TQi Receiver Only)
Breakaway Cable from
Distribution Block mounted on body
E
F
G
H
K
M
N
A
B
C
D
Part 6593
PRO SCALE® LIGHTING
DISTRIBUTION BLOCK
Breakaway Cable
to Lighting Power
Module on chassis
RedRed
White
White
Double
Jumper
Wiring Diagram
TRAXXAS.com
Traxxas, 6250 Traxxas Way, McKinney, TX 75070, Phone: [phone], Fax: [phone], e-mail: [email protected]
Chevrolet® and Blazer® are trademarks of General Motors.
All copyrights and trademarks are used by Traxxas under license.
Visit Traxxas.com/ProScaleLighting
for additional information about
installing and connecting accessories
such as auxiliary lighting (rock lights,
part #8026X, sold separately) to the
Pro Scale Lighting Module.