TREND DAF/8 User manual

DIGITAL ANGLE FINDER REF. DAF/8
INTENDED USE
SAFETY
DESCRIPTION OF PARTS
TECHNICAL DATA
Measuring Range: 000.0º - 220.0º (can reach 360.0º when locking knob is removed)
Working Temperature: +5ºC to +45ºC Working humidity: ≤ 85% RH
Working Current: ≤ 80 uA Resolution: 0.05º/3’ Accuracy 0.15º
Battery: CR2032 3V Lithium Battery Weight 351g
Denotes risk of personal injury, loss of life or damage to the tool in case of non-observance of the
instructions.The attention of UK users is drawn to The Provision and Use of Work Equipment Regulations
1998, and any subsequent amendments. Users should also read the HSE/HSC Safe Use of Woodworking
Machinery Approved Code of Practice and Guidance Document and any amendments. Users must be competent
in woodworking equipment before using our products.
Measuring Range Locking Positions
Thank you for purchasing this Trend product which should give lasting performance if used in accordance with
these instructions.
Four different measuring ranges can be achieved depending on the location of the locking knob.
Please note: LCD display will not show a minus ( - ) symbol.
Please note: LCD display will not show a minus ( - ) symbol.
This accessory is intended to be used to measure and transfer an angle.
Read and understand the instruction sheet carefully before using.This is a sensitive precision tool.
Do not disassemble or drop it. Please note the sharp edges, avoid scratching. Store out of reach of
children. Do not use as a toy or as a weapon. PLEASE KEEP THESE INSTRUCTIONS IN A SAFE PLACE.
CONFORMITY
DECLARATION
This product conforms with
EMC Directive 2004/108/EC.
ENVIRONMENTAL PROTECTION
Recycle raw materials instead of disposing as waste.
Packaging should be sorted for environmental-friendly recycling.
Separate collection.This product must not be disposed of with normal household waste.
Household User
Local regulations may provide for separate collection of electrical products from the household, at municipal
waste sites or by retailer when you purchase a new product. Please call Trend Customer Services for advice as
how to dispose of unwanted Trend electrical products in an environmentally safe way or visit www.trend-uk.com
Business User
Please call Trend Customer Services for disposal of unwanted Trend electrical products.
Batteries and the Environment
This unit uses Lithium Ion (Li-ion) batteries. When battery pack needs replacing,
we recommend the following: Discharge the energy from the batteries by running them
down completely and then remove them from the tool. Li-ion cells are recyclable so do not throw them
away with household waste.They may end up in an incinerator or landfill, which must be avoided.
Instead, take the batteries to a Trend Service Agent, your local Trend Stockist or a local recycling station. If
necessary contact your local municipality for disposal information. The collected batteries will be disposed of
properly and/or used for recycling purposes.
OPERATION
Press to turn off LCD.
Long press for 8 secs to turn off.
Press to switch between absolute & relative modes.
Long press to set the moving rule to zero.
To hold angle currently on the display.
HOLD
ON
OFF
ZERO
ABS
090.0 0ABS
C
L
O
S
E
O
P
E
N
123456789101112131415161718192021
1
16
248
4 12 20 28
16
248
4 12 20 28
16
248
4 12 20 28
16
248
4 12 20 28
16
248
4 12 20 28
16
248
4 12 20 28
16
248
4 12 20 28
16
248
4 12 20 28
2345678
24.5mm
Spirit level vial 36.5mm
HOLD
ON
OFF
ZERO
ABS
090.0 0ABS
C
L
O
S
E
O
P
E
N
123456789101112131415161718192021
1
16
248
4 12 20 28
16
248
4 12 20 28
16
248
4 12 20 28
16
248
4 12 20 28
16
248
4 12 20 28
16
248
4 12 20 28
16
248
4 12 20 28
16
248
4 12 20 28
2345678
Battery cover
268mm
HOLD
ON
OFF
ZERO
ABS
090.0 0ABS
C
L
O
S
E
O
P
E
N
123456789101112131415161718192021
1
16
248
4 12 20 28
16
248
4 12 20 28
16
248
4 12 20 28
16
248
4 12 20 28
16
248
4 12 20 28
16
248
4 12 20 28
16
248
4 12 20 28
16
248
4 12 20 28
2345678
254mm
LCD
display
Fixed
aluminium
stock
Hanging
hook
Metal moving
rule with 8”
(200mm)
scale.
Locking
knob
90º angle
checker
HOLD
ON
OFF
ZERO
ABS
090.0 0ABS
ZERO
ABS
ON
OFF HOLD
Analogue quadrant
High
resolution
to 0.05º
“ABS” Mode
TROUBLESHOOTING
Problem Possible Cause Solution
No display or Lower voltage, no battery or Reinstall battery or
ambiguous reading. incorrect installation of battery. replace battery.
Erratic Display. Misfunction caused by high vibration Press zero to reset zero.
or heavy swinging of rule.
Number skip or Internal error. Remove battery, wait
frozen display. one minute and replace.
GUARANTEE
All Trend products are guaranteed against any defects in either workmanship or material, except products that
have been damaged due to improper use or maintenance.
MAINTENANCE
The rule has been designed to operate for a long period of time with the minimum of maintenance.
Continual satisfactory operation depends upon proper tool care and regular cleaning.
Cleaning
nClean with mild liquid soap and a damp cloth. Dry with a soft cloth.
Never immerse in water. Rule requires no additional lubrication.
Storage
nReturn to packaging after use if it is not to be used for a long time. Store in a dry and shady place. Never
leave it outside or in a wet environment. Before storing, it is advisable to wipe surfaces with anti-rust oil.
HOLD
ON
OFF
ZERO
ABS
090.0 0
ABS
HOLD
ON
OFF
ZERO
ABS
090.0 0
ABS
HOLD
ON
OFF
ZERO
ABS
090.0 0
ABS
HOLD
ON
OFF
ZERO
ABS
000.0 0
ABS
Standard level surface.
Plumb surface
for measuring.
Spirit Level Application
Moving Rule Analogue Quadrant Instruction
HOLD
ON
OFF
ZERO
ABS
090.0
0ABS
ZERO
ABS
ON
OFF
HOLD
HOLD
ON
OFF
ZERO
ABS
090.0 0ABS
ZERO
ABS
ON
OFF HOLD
HOLD
ON
OFF
ZERO
ABS
090.0 0ABS
ZERO
ABS
ON
OFF
HOLD
ABS Setting
In ABS mode pressing zero/ABS
button for 5 seconds sets the zero
position of the moving blade.
ABS mode automatically recalls the
original position of zero after power off.
Display always reads upright. Put the moving rule on the same surface as the fixed stock.
HOLD
ON
OFF
ZERO
ABS
000.0 0
ABS
HOLD
ON
OFF
ZERO
ABS
045.0 0
ABS
HOLD
ON
OFF
ZERO
ABS
000.0 0
ABS
Under “ABS” mode
HOLD
ON
OFF
ZERO
ABS
000.0
0
ABS
HOLD
ON
OFF
ZERO
ABS
000.0 5
ABS
-45º
-0.05º
HOLD
ON
OFF
ZERO
ABS
045.0 0
ABS
45º 0º
HOLD
ON
OFF
ZERO
ABS
000.0 5
ABS
0.05º
HOLD
ON
OFF
ZERO
ABS
045.0 0
ABS
45.05º
90º
HOLD
ON
OFF
ZERO
ABS
090.0 0
ABS
HOLD
ON
OFF
ZERO
ABS
045.0 5
ABS
Analogue quadrant
resolution is 45º.
Display range of
analogue quadrant is 360º.
Range: -180º ~ 45º Range: -225º ~ 0º
Range: 0º ~ 225º
Range: -45º ~ 180º
Battery Care
WARNING! Insert battery correctly. Keep batteries away from children.
Do not swallow, open, recharge, or expose to water, fire or high
temperature: may explode, leak and cause damage.
C
L
O
S
E
O
P
E
N
CR2032
3V
+
Battery Fitting and Replacement
nTo fit or replace battery, twist cap on back of unit and remove.
nRemove battery carefully. Insert new battery type CR2032 3v.
nRe-insert cap and twist to close using direction arrows on the cap.
HOLD
ON
OFF
ZERO
ABS
090.0 0ABS
C
L
O
S
E
O
P
E
N
123456 789101112131415161718192021
1
16
248
4 12 20 28
16
248
4 12 20 28
16
248
4 12 20 28
16
248
4 12 20 28
16
248
4 12 20 28
16
248
4 12 20 28
16
248
4 12 20 28
16
248
4 12 20 28
2345 678
nTo remove locking knob rotate moving rule until
it reaches the stop, then unscrew knob.
nTo refit ensure the knob is placed in the enlarged end
of the slot and tighten into the relevant threaded hole.
nRotate locking knob anti-clockwise to loosen the
moving rule.
The measuring range can reach 360º
if you unscrew and remove the locking
knob.
nRotate locking knob clockwise to
tighten the moving rule.
nRotate locking knob anti-clockwise
to loosen the moving rule.
Threaded holes
HOLD
ON
OFF
ZERO
ABS
090.0 0
ABS
123456 789101112131415161718192021
7
16
824
28 20 12 4
16
824
28 20 12 4
16
824
28 20 12 4
16
824
28 20 12 4
16
824
28 20 12 4
16
824
28 20 12 4
16
824
28 20 12 4
16
824
28 20 12 4
6543210
HOLD
ON
OFF
ZERO
ABS
090.0 0
ABS
123456 789101112131415161
718192021
7
16
824
28 20 12 4
16
824
28 20 12 4
16
824
28 20 12 4
16
824
28 20 12 4
16
824
28 20 12 4
16
824
28 20 12 4
16
8
24
28 20 12
4
16
824
28 20 12 4
65432
10
Enlarged end of slot
Li-ion
Our policy of continuous improvements mean that specifications may change without notice. Trend
Machinery & Cutting Tools Ltd. cannot be held liable for any material rendered unusable, or for any
form of consequential loss.
© Copyright Trend 2013. E&OE.
® All trademarks acknowledged.
PP C/DAF/8 v1.0