TRENDnet TPL-310AP User manual

Safety
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pur-
suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television recep-
tion, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is con-
nected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two condi-
tions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for com-
pliance could void the user's authority to operate this equipment.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmit-
ter.

CE Mark Warning
This equipment complies with the requirements relating to electromagnetic compatibility, EN 55022
Class A for ITE, the essential protection requirement of Council Directive 2004/108/EC on the approxi-
mation of the laws of the Member States relating to electromagnetic compatibility and R&TTE Directive
1999/5/EC to meet the regulation of the radio equipment and telecommunications terminal equipment.
Company has an on-going policy of upgrading its products and it may be possible that information in
this document is not up-to-date. Please check with your local distributors for the latest information. No
part of this document can be copied or reproduced in any form without written consent from the
company.
RoHS
This product is RoHS compliant.

Table of Contents
Chapter 1: Product Overview........................................................................................... 6
1.1 Technical Features ................................................................................................. 8
1.1 Package Contents .................................................................................................. 9
1.2 System Requirements ............................................................................................ 9
1.3 Device Label......................................................................................................... 10
1.4 LEDs & Buttons .................................................................................................... 10
1.5 Top Panel............................................................................................................. 12
1.6 Defaults Settings.................................................................................................. 12
Chapter 2: Wireless Access Point Initial Setup............................................................... 13
Chapter 3: Wireless Access Point Web Management Interface .................................... 19
3.1 Default Configuration Settings ............................................................................. 19
3.2 Menu Items ......................................................................................................... 19
3.3 Status................................................................................................................... 20
3.4 Wireless............................................................................................................... 21
3.4.1 Apply/Reset Changes ..........................................................................................................21
3.4.2 Basic Settings.......................................................................................................................21
3.4.3 Multiple SSID .......................................................................................................................23
3.4.4 Active Wireless Client Table ................................................................................................24
3.4.5 Advanced Settings ...............................................................................................................24
3.4.6 Security ...............................................................................................................................25
WEP Security .................................................................................................................................26
WPA/WPA2 Security .....................................................................................................................27
WPA Mixed....................................................................................................................................28
3.4.7 Access Control ....................................................................................................................29
3.4.8 WDS Settings ......................................................................................................................30
3.4.9 Mesh Settings .....................................................................................................................31
3.4.10 Site Survey........................................................................................................................32
3.4.11 WPS ..................................................................................................................................33
3.4.12 Schedule...........................................................................................................................34
3.5 TCP/IP Settings..................................................................................................... 35
3.6 Log....................................................................................................................... 36
3.7 Statistics............................................................................................................... 37
3.8 Upgrade Firmware ............................................................................................... 37
3.9 Save/Reload Settings ........................................................................................... 37
3.10 Password.............................................................................................................. 38
3.11 System Time ........................................................................................................ 38
3.12 Logout.................................................................................................................. 38
Chapter 4: Powerline...................................................................................................... 39
4.1 Create a powerline network and extend you wireless network ........................... 40
4.2 Securing your Powerline Network ....................................................................... 42
4.3 Changing the Network Name/Security Key using the Sync Button....................... 42

4.4 Adding the Powerline Adapter to an Existing Powerline Network........................ 43
4.5 Overlapping Powerline Networks......................................................................... 44
4.6 Moving Powerline Adapters between different Powerline Networks .................. 45
Chapter 5: Powerline Configuration Utility.................................................................... 46
5.1 Software Installation............................................................................................... 46
5.2 Using the Utility ...................................................................................................... 50
Chapter 6: Troubleshooting............................................................................................ 52
Powerline............................................................................................................. 52
Wireless Installation Considerations .................................................................... 53
Chapter 7: Specifications ................................................................................................ 54

Chapter 1: Product Overview
The TPL-310AP 200Mbps Powerline AV Wireless N Access Point is an excellent
solution that can be used to extend your network using your home or small office
electrical wiring. In a home or small office building, use TPL-310AP adapters to link
multiple locations without the need to run long Ethernet cables. Combined with a single
broadband DSL/Cable Internet connection, every room with electrical power outlets can
provide easy access to your high-speed Internet connection.
The TPL-310AP 200Mbps Powerline AV Wireless N Access Point allows you to
create or extend a wireless network using powerline technology. Using powerline as the
network backbone, the TPL-310AP can be placed at where a wireless signal is needed,
rather than at the farthest corner of a wireless network. Multiple TPL-310AP adapters
can be used to cover larger areas without increasing wireless radiation and through the
use of powerline as your network backbone with no additional wiring required. In
addition, any Ethernet-enabled device may be connected to the 10/100Mbps Auto-MIDX
Fast Ethernet port.
The TPL-310AP coverage is provided by sending data signals through the walls
themselves via the electrical system using powerline technology and then supplying
802.11 wireless connectivity in the room where it is needed. In environments where
wireless cannot provide a high degree of performance/connectivity, powerline will
provide an alternative option to this obstacle. With 802.11n wireless data rates of up to
300Mbps and HomePlug® AV speeds of up to 200Mbps, this easy-to-setup solution can
provide fast streaming HD movies, online multiplayer games, and other data intensive
applications for today’s HD Entertainment Center demand.

This versatile Powerline product has many applications:
Expanding an Existing Powerline Network
If you have an existing Powerline AV network already installed, simply plug in
TRENDnet’s TPL-310AP into any outlet on your electrical system and connect it to your
Powerline network. You will then have Internet access from the TPL-310AP’s wireless
network and from its Ethernet port.
Expanding a Wireless Network
If you already have an existing wireless network and would like to expand wireless
coverage, simply connect a TRENDnet Powerline AV adapter to your existing router.
Then plug in TRENDnet’s TPL-310AP in an area with poor or no wireless coverage. Finally,
connect the TPL-310AP to the first Powerline adapter using the one-touch Sync button.
You will now have wireless coverage in an area that was not covered in the past.
Expanding a Wired Network
If you have an existing wired router and would like to create both a wireless and a
Powerline network, simply connect TRENDnet’s TPL-310AP to your wired router and plug
it into an electrical outlet. To further expand the Powerline network, plug in up to 15
additional TRENDnet Powerline AV adapters into any outlet on your electrical system.
If you have an existing wired router and would like to create both a wireless and a
Powerline network, simply connect TRENDnet’s TPL-310AP to your wired router and plug
it into an electrical outlet. To further expand the Powerline network, plug in up to 15
additional TRENDnet Powerline AV adapters into any outlet on your electrical system.
Combination 200Mbps Powerline adapter and 300Mbps wireless n access point
Create a 300Mbps wireless network from any room in your home
Connect up to 16 high speed powerline adapters
Wireless n access point offers Access Point, Client, WDS, and Mesh mode
functionality
Advanced encryption

1.1 Technical Features
Powerline
1 x 10/100Mbps Auto-MDIX Ethernet port
Connect one 200Mbps** Powerline AV Adapter to the Internet and then plug in up to 15* addi-
tional Powerline AV adapters for instant building connectivity
One-touch Sync button networks adapters quickly
Share data intensive files, play games, download music, and more at faster data transfer rates
Advanced 128-bit AES encryption to ensure total network security
Neighbor network support for up to 4 overlapping networks
Tri-color LED Indicator
Network signal transmits up to 300 meters (984ft.)
Auto QoS support through traffic classification and multiple priority queuing
Windows-based Powerline configuration utility: compatible with Windows 7 (32/64-bit), Vista
(32/64-bit), and XP (32/64-bit) operating systems
Wireless
Integrated high performance wireless n access point
Based on IEEE 802.11n technology and compliant with IEEE 802.11b/g standards
High-speed data rates of up to 300Mbps*** with IEEE 802.11n
One-touch Wi-Fi Protected Setup (WPS) button connects wireless clients quickly
Supports Access Point or Access Point (AP) Client (wireless adapter) mode
In Access Point mode: expand a wireless network using Repeater mode (listed as AP Mode Sup-
port), Wireless Distribution System (WDS), or Mesh mode (bridging)
MAC filter feature for added security (AP mode only)
Wireless security up to WPA/WPA2-RADIUS
Create a weekly schedule to enable or disable wireless network
Wi-Fi Multimedia (WMM) Quality of Service (QoS) support
Broadcast up to 4 SSIDs with different wireless encryption
Web graphical user interface provides backup, configuration, and firmware management
Wireless indoor coverage up to 100 m (328 ft.)***
3-year limited warranty
* Maximum of 16 adapters (nodes) recommended for streaming video across your network. Additional
adapters may decrease performance.
** 200Mbps is the maximum theoretical Powerline data rate. Actual throughput will vary depending
on environment.
***Maximum wireless signal rates are referenced from IEEE 802.11 theoretical specifications. Actual
data throughput and coverage will vary depending on interference, network traffic, building materials
and other conditions.
**** Networked Powerline devices need to be plugged into power outlets that are on the same elec-
trical system.
*****It is not recommended to use this product on electrical systems that use AFCI circuit breakers or
plugged into GFI protected outlets as this may cause performance degradation or loss in connectivity.

1.1 Package Contents
The product package should contain the following items:
TPL-310AP
Multi-Language Quick Installation Guide
CD-ROM (Utility & User’s Guide)
Network Cable (1.5 m / 4.9 ft.)
If any of the parts are incorrect, missing, or damaged, contact your dealer. Keep the
carton, including the original packaging materials, in case you need to return the
Powerline adapter for repair.
1.2 System Requirements
CD-ROM drive
A Desktop or Laptop PC with wired or wireless Network Adapter Installed
Existing 10/100Mbps wired network when TPL-310AP is used as a bridge device
Web Browser: Internet Explorer (6.0 or higher)
Additional HomePlug® AV powerline adapter
(e.g. TRENDnet TPL-303E, TPL-304E, TPL-305E or another TPL-310AP)
Note: You will need at least 2 powerline adapters to establish a powerline network. Please
ensure that you have an additional powerline adapter before following the installation pro-
cedure for this product.
Powerline Configuration Utility System Requirements
Supported Operating
Systems
CPU
Memory
Windows 7 (32/64-bit)
1GHz or above
1GB RAM or above
Windows Vista (32/64-bit)
800MHz or above
512MB RAM or above
Windows XP (32/64-bit)
300MHz or above
256MB RAM or above

Default Subnet Mask
1.3 Device Label
The device label can be located on the back of the device where the power prong is found.
1.4 LEDs & Buttons
Ethernet
(ETH)
Wi-Fi
Protected
Setup
(WPS)
Powerline Firmware Version
Product Hardware Version
Device Password (DPW)
Device MAC Address
Device Serial Number
Product Model
Default IP Address
Wireless
(WIFI)
Powerline
(PLC)
Power
(PWR)
Fast Ethernet Port
Reset Button
WPS Button
Sync Button

*Note: The following factors may affect the powerline network’s connection quality:
Noise –Generated by appliances that are connected to your electrical system through power outlets that have high
power consumption requirements. (e.g. Microwaves, ovens, blow dryer, iron, dishwasher, etc.) The quality of your
household electrical wiring may also cause additional noise on your electrical system.
Distance –Long lengths of electrical wiring through your electrical system between connected powerline adapters.
LED
Color
Sequen
ce
Definition
PWR (Power)
Green
Solid
Device powered On
N/A
Off
Device powered Off
PL (Powerline)
Note: LED color
indicates the strength
and quality of the
powerline connection
through the electrical
system
Green
Solid
Powerline Connected (Connection Quality is Best)
Blinking
Syncing or Powerline Data Transmitting/Receiving (Connection Quality is
Best)
Amber
Solid
Powerline Connected (Connection Quality is Better)
Blinking
Powerline Data Transmitting/Receiving (Connection Quality is Better)
Red
Solid
Powerline Connected (Connection Quality is Good)
Blinking
Powerline Data Transmitting/Receiving (Connection Quality is Good)
N/A
Off
Powerline is not synced or connected
ETH
(Ethernet Port)
Green
Solid
10/20 Mbps, 100/200Mbps, or 1000/2000Mbps (Half/Full
Duplex) Connected
Blinking
10/20Mbps, 100/200Mbps, or 1000/2000Mbps (Half/Full Duplex) Data
Transmitting/Receiving
N/A
Off
Port Disconnected/No Ethernet Link
WIFI
(Wireless)
Green
Blinking
Wireless is on or enabled / Wireless Data Transmission
N/A
Off
Wireless is off or disabled
WPS
(WiFi Protected Setup)
Green
Blinking
WPS is activated
N/A
Off
WPS is not activated or disabled
Button
Action
Function
Sync
Push/Hold for 2 sec
Initiate Sync/Connection and generate random network name/key on first
adapter (PWR LED will start blinking)
Match network name/key on secondary or additional adapter and connect to
first adapter. (PWR LED will start blinking)
Note: The secondary or additional powerline adapter’s Sync button must also
be pushed within 2 minutes (120 sec) of pushing the Sync button of the first
adapter in order to establish connectivity.
Push/Hold for 10 sec
Erases the network name/key (All LEDs will turn off and turn back on)
WPS
Push/Hold for 3 sec
Activates Wi-Fi Protected Setup (WPS)
Reset
Push/Hold for 1 sec
Reset to Powerline factory defaults only (All LEDs will turn off and turn back on,
PL LED will blink Amber)
Note: Will reset to the factory default private network name “HomePlugAV”.
This will not reset Wireless Access Point settings and the settings will remain
intact.
Push/Hold for 5 sec
Reset to Wireless Access Point factory defaults only (All LEDs will turn off and
turn back on)
Note: This will not reset Powerline settings and the settings will remain intact.

1.5 Top Panel
There On/Off Power switch is located on the top panel of the device which is used to power the device
on or off.
1.6 Defaults Settings
Wireless AP
Setting
IP Address / Subnet Mask
192.168.10.100 / 255.255.255.0
SSID
TRENDnet310
SSID Broadcast
Enabled
Mode
Access Point (AP)
Channel
Auto
Channel Width
20MHz
802.11 Mode
802.11b/g/n Mixed
Security
Disabled
Username / Password
admin / admin
Powerline
Setting
Network Name/Security Key
HomePlugAV
On/Off Power
Switch

Chapter 2: Wireless Access Point Initial Setup
When installing the TPL-310AP for the first time, it required for you to configure the device
from a wired computer. Since the default IP address of the TPL-310AP is 192.168.10.100, please make
sure to assign an IP address to the TPL-310AP that is NOT assigned to any other devices on your net-
work. If your network IP address range is NOT 192.168.10.x, then the TPL-310AP IP address should be
assigned with your network’s IP address range (i.e. 192.168.1.x, 192.168.2.x, 192.168.0.x) This chapter
covers the typical configuration of the TPL-310AP in Access Point (AP) mode using the Setup Wizard. If
you are an experienced user, other web configuration settings can be referenced in Chapter 3. Once
the initial setup is complete, Chapter 4 will cover creating a powerline network with one additional po-
werline adapter, or adding the TPL-310AP to existing powerline network.
1. Plug the TPL-310AP into an available power outlet within reach of your computer’s network ca-
ble.
2. Connect a network cable from the TPL-310AP Wireless Access Point’s network port (located at
the bottom of the device) into the computer’s network port.
3. Move the power switch (located at the top of the device) to the “On” position.
4. Assign a static IP address to your computer’s network adapter to 192.168.10.10 and subnet
mask 255.255.255.0.
Windows 7: Click on the Start Button, select Control Panel, click Network and Internet, click on
Network and Sharing Center, and click Change Adapter Settings. Then, right-click the Local Area
Connection icon and click Properties. Click Internet Protocol Version 4 (TCP/IPv4) and then click
Properties. Select Use the following IP address, and manually enter the IP address settings.
Windows Vista: Click on the Start Button, select Control Panel, click Network and Internet, click
on Network and Sharing Center, and click Manage Network Connections. Then, right-click the
Local Area Connection icon and click Properties. Click Internet Protocol Version 4 (TCP/IPv4) and
then click Properties. Select Use the following IP address, and manually enter the IP address set-
tings.
Windows XP/2000: Click on the Start Button, select Control Panel, double-click the Network
Connections icon, and then click Properties. Click Internet Protocol (TCP/IP) and then click Prop-
erties. Select Use the following IP address, and manually enter the IP address settings.
5. Open your Web browser, and type http://192.168.10.100 in the Address bar, and then press En-
ter.

6. Enter the User Name and Password and then click OK.
7. In the menu in the left-hand panel, click on Setup Wizard.
8. In the Setup Wizard window, click Next

9. Configure the LAN Interface Settings of the TPL-310AP. Click Next.
IP Address: The assigned IP address should match the network IP address range of your network.
This IP address should not be used by any other devices on your network.
Subnet Mask: The assigned Subnet Mask should match the network Subnet Mask of your network.
In most cases, the default Subnet Mask setting (255.255.255.0) should be fine.
DHCP: Setting DHCP to Client will set your device to obtain an IP address automatically from your
DHCP server (router). If Disabled, you will need to manually configure the IP address settings.
Note: It is recommended to manually configure the LAN Interface Settings (IP Address and Subnet
Mask) in case you need access the device in the future. Please write down the IP address settings as-
signed for future reference.

10. Configure the Wireless LAN Settings. Then click Next.
Band: In most cases, the default setting (2.4GHz (B+G+N)) should be fine.
Mode: In most cases, the default setting AP (Access Point) should be fine.
Network Type: This setting does not apply to (AP) mode, only in (AP Client) mode. Continue to the next
setting.
SSID: The SSID is the network name of your wireless network (The name wireless clients will discover,
when scanning for wireless networks). It is recommended to assign a unique SSID (Network Name) and
to not assign anything that would be personally identifying like “Smith Family Network” however, an
SSID easily identifiable when searching for available wireless networks. Manually enter the name of
your wireless network.
Channel Width: In most cases, the default setting (20MHz) should be fine.
Channel Number: This setting is only configurable when setting the Channel Width to 40MHz. In most
cases, the default setting (Auto) should be fine.
Enable MAC Clone (Single Ethernet Client): This setting does not apply to (AP) mode, only in (AP Client)
mode.

11. Configure the Wireless Security Settings. Click the drop-down menu Encryption: and select
WPA2(AES).
Note: To protect your network from unauthorized wireless access, it is strongly recommended
to enable wireless security. It is highly recommended to use WPA2 if all of your wireless devices
also support WPA2, since it is the highest security protocol supported currently. Once wireless
security is enabled on the TPL-310AP, each wireless computer or device must be configured to
use the same protocol (WEP, WPA, WPA2) and configured with the same security key. Make
sure your wireless devices support the security protocol configured on the TPL-310AP. If you are
unsure of the security protocols supported, please refer the manuals for your wireless devices
or contact the manufacturer to find out these details. The example demonstrates how to confi-
gure the TPL-310AP for WPA2.
12. Click the drop-down menu Pre-Shared Key Format: and select Passphrase.

13. In the box next to Pre-Shared Key, manually enter your wireless security key (8 –63 characters).
Click Finished.
Note: This will be the key required to enter for your wireless computers or devices when con-
necting wirelessly. If needed, write down your wireless security settings and security key for
reference when configuring your other wireless devices.
14. Please wait 25 seconds while the TPL-310AP applies the changes and reboots.
15. If you are finished configuring the TPL-310AP wireless settings, after the changes are applied
and the TPL-310AP has rebooted, disconnect the network cable from the TPL-310AP Ethernet
network port, and unplug the TPL-310AP from the power outlet and skip over to the Powerline
section (Chapter 4) for creating a powerline network. If you would like to configure any addi-
tional wireless parameters, continue to Chapter 3 for any additional wireless settings.
16. Change your computer’s network adapter settings back to obtain an IP address automatically.
Windows 7: Click on the Start Button, select Control Panel, click Network and Internet, click on
Network and Sharing Center, and click Change Adapter Settings. Then, right-click the Local Area
Connection icon and click Properties. Click Internet Protocol Version 4 (TCP/IPv4) and then click
Properties. Select Obtain an IP address automatically.
Windows Vista: Click on the Start Button, select Control Panel, click Network and Internet, click
on Network and Sharing Center, and click Manage Network Connections. Then, right-click the
Local Area Connection icon and click Properties. Click Internet Protocol Version 4 (TCP/IPv4) and
then click Properties. Select Obtain an IP address automatically.
Windows XP/2000: Click on the Start Button, select Control Panel, double-click the Network
Connections icon, and then click Properties. Click Internet Protocol (TCP/IP) and then click Prop-
erties. Select Obtain an IP address automatically.

Chapter 3: Wireless Access Point Web Management Interface
3.1 Default Configuration Settings
3.2 Menu Items
Setup Wizard: Quickly configure the basic settings such as IP
settings, SSID (Wireless Network Name), and Wireless Security.
Status: Displays the current device status and some basic
settings of the device.
Wireless: Configure the wireless parameters such as AP, WDS,
Mesh, AP client, and repeater modes. Configure wireless
security settings, WPS, access control such as MAC filtering,
and wireless scheduling.
TCP/IP Settting: Configure the IP address settings for the
local area network or Ethernet port.
Log: Displays the device internal system log or configure the
device to send system logs to a remote log server (Syslog).
Statistics: Displays the number of packets transmitted and
eceived on the wireless and wired interfaces.
Upgrade Firmware: Upgrade the device firmware.
Save/Reload Settings: Backup configuration, restore from configuration file, and reset the wireless
access point settings to factory defaults.
Password: Change the device username and password.
System Time: Set the device system time.
Logout: Logout of the web management interface.
Wireless AP
Setting
IP Address / Subnet Mask
192.168.10.100 / 255.255.255.0
SSID
TRENDnet310
SSID Broadcast
Enabled
Mode
Access Point (AP)
Channel
Auto
Channel Width
20MHz
802.11 Mode
802.11b/g/n Mixed
Security
Disabled
Username / Password
admin / admin

3.3 Status
Items
Information
Uptime
The period that you turn the device on.
Firmware version
The current firmware version of the device.
Build Time
The build time of the device originally.
Mode
Displays the current Access Point mode.
Band
The band that the wireless AP operating.
SSID
The name of this wireless network.
Channel Number
The channel that the wireless network using.
Encryption
The security encryption type that the wireless network using.
BSSID
The Basic Service Set Identity of this AP (This parameter is the
same as the MAC address of LAN port)
Associated Clients
The number of members who is currently connected with this AP.
Attain IP Protocol
Displays whether the IP address is set statically (Fixed IP) or
obtained automatically (DHCP).
IP Address
The current IP address of this AP.
Subnet Mask
The current subnet mask of this AP.
Default Gateway
The current default gateway of this AP.
MAC Address
The current MAC address of this AP.