TRENDnet TV-VS1 User manual

- 1 -
PREFACE
Thank you for purchasing the TV-VS1/TV-VS1P Video Encoder, a
standalone system that can easily connect the analog camera to your
network.
With support for latest H.264 technology, you can use the analog camera
to record high-quality digital streaming video to your hard drive, enable
motion detection and setup automated e-mail alerts for security. The
built-in microphone and audio ports provide you with the extensive
audio function, allowing you to “watch” and “listen” from the connected
camera.
Compared to the conventional camera, this Video Encoder features a
built-in CPU and web-based solutions that can provide a cost-effective
solution to transmit the real-time high-quality video images and sounds
synchronously for monitoring. The Video Encoder can be managed
remotely, so that you can use a web browser to access and control it
from any desktop/notebook computer over the Intranet or Internet.
TV-VS1P Compliant with IEEE802.3af PoE (Power over Ethernet) standard,
the Video Encoder provides you with more flexibility of device
installation according to your application. The device can be powered by
the Ethernet, so that you can place the device anywhere without a
power outlet supported.
The simple installation procedures and web-based interface allow you to
integrate it into your network easily. With comprehensive applications
supported, the Video Encoder is your best solution to transmit the real-
time high-quality video images for monitoring.

- 2 -
This Advanced Installation Guide provides you with the instructions and
illustrations on how to use your Video Encoder, which includes:
Chapter 1 Knowing Your Video Encoder describes the component
features of the device, as well as the applications of the
device.
Chapter 2 Hardware Installation helps you install the device
according to your application environment. You can use
this device at home, at work, at any where you want.
Chapter 3 Accessing the Video Encoder lets you start using your
device without problem. The device can be set up easily
and work within your network environment instantly.
Chapter 4 Configuring the Video Encoder guides you through the
configuration of the device using the Web browser on your
PC.
Chapter 5 Appendix provides the specification of the device and some
useful information for using your device.
NOTE The illustrations and configuration values in this guide are for reference
only. The actual settings depend on your practical application of the
Video Encoder.

- 3 -
Contents
PR E F A C E ....................................................................... 1
CH A P T E R 1 ................................................................... 5
KN O W I N G YO U R VI D E O EN C O D E R ......................................... 5
1.1 CHECKING THE PACKAGE CONTENTS .............................................5
1.2 COMPONENT FEATURES .............................................................6
1.3 FEATURES AND BENEFITS ............................................................8
1.4 SYSTEM REQUIREMENT ............................................................10
CH A P T E R 2 .................................................................. 11
HA R D W A R E IN S T A L L A T I O N ............................................... 11
2.1 MOUNTING THE DEVICE ON THE WALL .......................................11
2.2 CONNECTING THE CABLES.........................................................12
2.3 APPLICATIONS OF THE VIDEO ENCODER.......................................13
CH A P T E R 3 .................................................................. 14
AC C E S S I N G TH E VI D E O EN C O D E R ....................................... 14
3.1 USING IP SETUP......................................................................14
3.2 ACCESSING TO THE DEVICE ........................................................18
3.3 CONFIGURING THE IP ADDRESS OF THE COMPUTER .......................21
CH A P T E R 4 .................................................................. 22
CO N F I G U R I N G THE VI D E O EN C O D E R .................................... 22
4.1 USING THE WEB CONFIGURATION..............................................22
4.2 USING SMART WIZARD ............................................................23
4.3 BASIC SETUP ..........................................................................26
4.4 NETWORK SETTINGS ................................................................31
4.5 SETTING UP VIDEO &AUDIO .....................................................38
4.6 EVENT SERVER CONFIGURATION ................................................45
4.7 MOTION DETECT.....................................................................53
4.8 EVENT CONFIGURATION ...........................................................54
4.9 TOOLS...................................................................................60
4.10 RS-485.................................................................................62
4.11 SETTING UP SD CARD ..............................................................66
4.12 INFORMATION ........................................................................67
CH A P T E R 5 .................................................................. 69

- 4 -
H ow t o a cc es s t h e V id e o E n co d er b e hind a Ro ut er ....... 69
Ap p en d ix .................................................................. 75
A.1 SPECIFICATION........................................................................75
A.2 GPIO TERMINAL APPLICATION ..................................................77
A.4 GLOSSARY OF TERMS ...............................................................79
L imit e d W a rran ty ...................................................... 88

- 5 -
CHAPTER 1
KNOWING YOUR VIDEO ENCODER
1.1 Checking the Package Contents
Check the items contained in the package carefully. You should have the
following:
TV-VS1 or TV-VS1P
Multi-Language Quick Installation Guide
CD-ROM (Utility & User’s Guide)
GPIO Connector
Network Cable (RJ-45)
Audio Y cable (3.5mm Jack)
Power Adapter (12VDC, 1.5A)
Mounting Kit
NOTE Any content is damaged or missing, please contact the local authorized
dealer for replacement.

- 6 -
1.2 Component Features
Front Panel
NO.
Item
Function

Video In
Connect an analog camera with the composite video
output (BNC type).

Video Out
Connect an external video device with the composite
video input (BNC type) to display the camera’s image on
a conventional monitor.

Line In
Connect CCTV camera’s audio out to Video Encoder’s
Line In.

Line Out
Connect an external active speaker to broadcast on-the-
spot sound of the connected CCTV camera.





- 7 -
Rear Panel
NO.
Item
Function

DC Power
Connector
Connect one end of power plug into the power source
and the other end to the device.

LED
Power LED (upper) will light a steady amber light to
indicate the device is powered on.
Link LED (lower) will blink a green light to indicate the
device’s network connectivity.

GPIO and
RS485
Connect the external devices for trigger and advanced
functions.
For more information, refer to the Appendix, GPIO
Terminal Application.

Ethernet
Connector
Connect the network cable.
The connector supports the NWay protocol so that the
device can detect the network speed automatically.

SD Card
Slot
Insert the SD card to expand the storage space for the
device (up to 32GB)

Reset
Button
Press to restart the device when it is pressed quickly;
press and hold for five seconds to restore the factory
default settings.







- 8 -
1.3 Features and Benefits
H.264/MPEG4/MJPEG Multi-codec Supported
The device provides you with excellent images by the
H.264/MPEG4/ MJPEG multi-codec selectable technology,
allowing you to adjust image size and quality, and bit rate
according to the networking environment.
Flexible Audio Capability
The device allows you to connect the external microphone to
receive on-the-spot audio via the Internet, allowing you to
monitor the on-site voice. In addition, you can connect an external
active speaker to the device to broadcast the received sound
through the connected camera.
Supports RTSP
The device supports RTSP (Real Time Streaming Protocol), which is
a technology that allows you to view streaming media via the
network. You can view the real-time video with the Quick Time
player or RealPlayer. To view the real-time streaming image on
your computer, open the Web browser and enter the RTSP link:
MPEG4 stream: rtsp://(IP address of the device)/mpeg4
H.264 stream: rtsp://(IP address of the device)/h264
I/O Connectors and RS-485 Provided
The I/O connectors (IN/OUT) of the device provide the physical
interface to send and receive digital signals to a variety of external
alarm devices (such as motion detection, event triggering, alarm
notification, and a variety of external control functions). The pins
TX+ & TX- of the I/O connectors are used for RS-485 data
transmission, which allow you to connect a special featured
device (such as an external device stand with rotation function)
and then configure the settings and control the device from the
GPIO Trigger window of Web Configuration.

- 9 -
Remote Control Supported
By using a standard Web browser, the administrator can easily
change the configuration of the device via Intranet or Internet. In
addition, the device can be upgraded remotely when a new
firmware is available. The users are also allowed to monitor the
image and take snapshots via the network.
Multiple Profiles Supported
The device supports multiple profiles simultaneously, so that you
can separately set up different image settings (such as image
quality and frame rate) for the three video types of the device:
H.264, MPEG4, MJPEG, and 3GPP.
Multiple Platforms Supported
The device supports multiple network protocols, including TCP/IP,
SMTP e-mail, HTTP, and other Internet related protocols.
Therefore, you can use the device in a mixed operating system
environment, such as Windows® 7/Vista/XP.
Multiple Applications Supported
Through the remote access technology, you can use the device to
monitor various objects and places for your own purposes. For
example, babies at home, patients in the hospital, offices and
banks, and more. The device can capture both still images and
video clips, so that you can keep the archives and restore them at
any time.
PoE Supported (TV-VS1P only)
PoE (Power over Ethernet) standard enables the device to be
powered by the Ethernet, which simplifies your surveillance
system by eliminating the need of power outlet. The PoE device
features both stability and security, providing a cost-saving
solution to your application of Internet surveillance.

- 10 -
1.4 System Requirement
Networking
LAN 10Base-T Ethernet or 100Base-TX Fast
Ethernet; Auto-MDIX
IEEE 802.3af PoE (TV-VS1P only)
Accessing the Device using Web Browser
Platform Microsoft® Windows® 7/Vista/XP
CPU Intel Pentium III 800MHz or above
RAM 512MB
Resolution 800x600 or above
User Interface Microsoft® Internet Explorer 6.0 or above;

- 11 -
CHAPTER 2
HARDWARE INSTALLATION
2.1 Mounting the Device on the Wall
The provided mounting Kit is used to mount the device on the wall or
ceiling. The example below is wall mounting installation. You can place
the device flexibly according to your need.
a. Drill four mounting holes into the wall.
b. Hammer the plastic anchors into the holes.
c. Mount the device onto the wall with four screws.

- 12 -
2.2 Connecting the Cables
1. Connecting the device to power source
Use the provided power adapter to connect the device to the power
source, such as the electrical outlet on the wall, and connect the
other end to the device. You can verify the power status from the
Power LED on the rear panel of the device.
2. Connecting the device to LAN
Use the provided Network cable to connect the device to your local
area network (LAN). Once connected, the Link LED starts flashing
green light.
3. Connecting the camera to the device
Connects a CCTV analog camera to the Video Encoder so that the
Video Encoder can work within your surveillance solution. To
connect the camera, plug one end of the BNC cable to the Video in
connector of the device and the other end to the Video out
connector of the camera.

- 13 -
2.3 Applications of the Video Encoder
The video encoder can be applied in multiple applications, including:
Monitor local and remote places and objects via Internet or
Intranet.
Capture still images and video clips remotely.
Upload images or send email messages with the still images
attached.
The following diagram explains one of the applications for your Video
Encoder and provides a basic example for installing the device.
Home Applications of the PoE Video Encoder
*Please have the Video Encoder enclosed by waterproof housing when using in outdoor.

- 14 -
CHAPTER 3
ACCESSING THE VIDEO ENCODER
3.1 Using IP Setup
The camera comes with a conveniently utility, IP Setup, which is included
in the Installation CD-ROM, allowing you to search the camera on your
network easily.
1. Insert the Installation CD-ROM into your computer’s CD-ROM drive
to initiate the Auto-Run program.

- 15 -
2. Click Install to install the IPSetup.
3. Click Finish to finish the installation.

- 16 -
4. After installing the IPSetup utility, the application is automatically
installed to your computer, and creates a folder in “Start
\Program\TRENDnet\IPSetup”.
5. Click Start > Programs > TRENDnet > IPSetup, and then click IPSetup
6. The IPSetup window will appear. It will search the Camera within
the same network.
Video Encoder display area

- 17 -
-Camera Display Area: It shows the connected camera(s) within the
same network. By default, the IP setting on the Camera is set up
DHCP. If you have DHCP server, the camera will automatic get the IP
address from DHCP server. If you do not have DHCP server on your
network, it will show the default IP as 192.168.10.30.
Double click the IP address; it will link to Camera’s Web
Configuration page.
-Change IP: Click this button to bring up the following window. It
allows you to change the IP Address. You can select either Static IP
or click DHCP. Then, enter the Administrator ID & password. By
default ID/password is: admin. When complete, click “Change”.
-Search: Click this button to search the connected camera
within the network.
-Exit: Click this button to exit the program.

- 18 -
3.2 Accessing to the device
Whenever you want to access the device:
1. Since the default configuration of the Video Encoder is DHCP mode
enabled, you are recommended to launch IPSetup to search the IP
address that is assigned to the device by the DHCP server, and then
click Link to access the device via the Web browser.
2. If Network Camera can't get IP Address under DHCP mode, the
default IP Address will be 192.168.10.30.
3. When the login window appears, enter the default User name
(admin) and password (admin) and press OK to access to the main
screen of the device’s Web Configuration.
NOTE If you are initially access to the Video Encoder, you will be ask to install
a new plug-in for the device. Permission request depends on the
Internet security settings of your computer. Click Yes to proceed.

- 19 -
After you login into the Web Configuration of the device, the Main
screen will appear as below:
The Main screen of the Web Configuration provides you with many
useful information and functions, including:
Live View/Setup Switch:
Click the button to configure the device. For
details, see Chapter 4.
Click the button to return to the Main screen to
view the live view image.
Compression Buttons: Select to transmit and record the video using
H.264, MPEG4 or MJPEG compression.
Function Buttons: Use these buttons to control the audio, video,
and trigger functions.
Manual Record allows you to record and save a video clip.





