TRENDnet TEG-PCITXM User manual

32-bit PCI
10/100/1000Mbps
Gigabit Ethernet Card
User’s Guide
FCC Warning
This equipment has been tested and found to comply with
the regulations for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with this
user’s guide, may cause harmful interference to radio
communications. Operation of this equipment in a
residential area is likely to cause harmful interference, in
which case the user will be required to correct the
interference at his own expense.
CE Mark Warning
This is a Class B product. In a domestic environment, this
product may cause radio interference, in which case the
user may be required to take adequate measures.
VCCI Warning
P/N: 1907GA1100T5000 Rev.A1-01

TABLE OF CONTENTS
INTRODUCTION.............................................................. 1
FEATURES ......................................................................... 1
GIGABIT ETHERNET TECHNOLOGY .................................. 2
FAST ETHERNET TECHNOLOGY........................................ 3
UNPACKING AND INSTALLATION ........................... 4
UNPACKING ...................................................................... 4
INSTALLING THE GIGABIT ETHERNET CARD ................... 5
CONNECTING THE NETWORK CABLE ............................... 6
SOFTWARE INSTALLATION............................................... 6
LED INDICATORS........................................................... 7
TECHNICAL SPECIFICATIONS .................................. 8

1
INTRODUCTION
Thank you for choosing the 10/100/1000Mbps Gigabit
Ethernet Card for 32-bit PCI Bus-equipped personal
computers. The 32-bit PCI 10/100/1000Mbps Gigabit
Ethernet Card is ideal for speeding up data transfers for
network servers and other computers, such as those used for
video-conferencing, that send and/or receive large amounts
of data. The 32-bit PCI 10/100/1000Mbps Gigabit Ethernet
Card also includes the newest networking technologies,
such as multicasting support, that use network bandwidth
more efficiently and further help the card maximize data
throughput.
Features
IEEE 802.3, 802.3u and 802.3z compliant
Support 32-bit 33/66Mhz PCI Local Bus Master
high-speed operation of Rev.2.1/2.2 specification
Plug-and-Play installation
One RJ-45 connector: Auto detection of 10Mbps
Ethernet, 100Mbps Fast Ethernet and 1000Mbps
Gigabit Ethernet & Auto MDI-X
Supports 10/100/1000Mbps Auto-negotiation
operation
Full Duplex support for 10/100/1000Mb/s data rates
Auto MDI-II/MDI-X crossover for all three speeds
128Kb RAM on-chip buffer
802.3x Full duplex flow control, including
automatic transmission of Pause frames based on Rx
FIFO thresholds
Five LED indicators for easy diagnostic
2
Gigabit Ethernet Technology
Gigabit Ethernet is an extension of IEEE 802.3 Ethernet
utilizing the same packet structure, format, and support for
CSMA/CD protocol, full duplex, and management objects,
but with a tenfold increase in theoretical throughput over
100Mbps Fast Ethernet and a one hundred-fold increase
over 10Mbps Ethernet. Since it is compatible with all
10Mbps and 100Mbps Ethernet environments, Gigabit
Ethernet provides a straightforward upgrade without
wasting a company’s existing investment in hardware,
software, and trained personnel.
The increased speed and extra bandwidth offered by
Gigabit Ethernet is essential to coping with the network
bottlenecks that frequently develop as computers and their
busses get faster and more users use applications that
generate more traffic. Upgrading key components, such as
your backbone and servers to Gigabit Ethernet can greatly
improve network response times as well as significantly
speed up the traffic between your subnets.
Gigabit Ethernet enables Twisted-Pair cable connections to
support video conferencing, complex imaging, and similar
data-intensive applications. Likewise, since data transfers
occur 10 times faster than Fast Ethernet, servers outfitted
with Gigabit Ethernet NIC’s are able to perform 10 times
the number of operations in the same amount of time.

3
Fast Ethernet Technology
The growing importance of LANs and the increasing
complexity of desktop computing applications are fueling
the need for high performance networks. A number of
high-speed LAN technologies have been proposed to
provide greater bandwidth and improve client/server
response times. Among them, 100BASE-T (Fast Ethernet)
provides a non-disruptive, smooth evolution from the
current 10BASE-T technology. The non-disruptive and
smooth evolution nature, and the dominating potential
market base, virtually guarantee cost effective and high
performance Fast Ethernet solutions in the years to come.
100Mbps Fast Ethernet is a new standard specified by the
IEEE 802.3 LAN committee. It is an extension of the
10Mbps Ethernet standard with the ability to transmit and
receive data at 100Mbps, while maintaining the CSMA/CD
Ethernet protocol. Since the 100Mbps Fast Ethernet is
compatible with all other 10Mbps Ethernet environments, it
provides a straightforward upgrade and takes advantage of
the existing investment in hardware, software, and
personnel training.
4
UNPACKING AND INSTALLATION
This chapter provides unpacking and installation
information for the 32-bit PCI 10/100/1000Mbps Gigabit
Ethernet Card.
Unpacking
CAUTION: Under ordinary circumstances, the 32-bit PCI
10/100/1000Mbps Gigabit Ethernet Card will not be
affected by static charge as may be received through
your body during handling of the unit. However, there
are special circumstances where you may carry an
extraordinarily high static charge, and possibly
damage the card and/or your computer. It is good
practice to eliminate all static electricity by touching
a ground (an unpainted metal area of your computer
chassis, for example) before performing any
installations.
Open the shipping carton and carefully remove all items. In
addition to this User's Guide, ascertain that you have:
One 32-bit PCI 10/100/1000Mbps Gigabit Ethernet
Card.
One Driver Diskette
This User’s Guide.
If any item is found missing or damaged, please contact
your local reseller for replacement.
.

5
Installing the Gigabit Ethernet Card
1. Shut down the computer, unplugs its power cord, and
remove the chassis cover.
2. Insert the contact edge of the Gigabit Ethernet card into
the connector of any available PCI Bus Master
expansion slot. Press the card firmly into the connector
such that the card’s contacts are fully seated in the
connector, this card can put either in 32-bit or 64-bit
PCI slot, but it is recommended that the card to put in
the PCI slot supported 66Mhz to have the maximum
performance.
3. Install the bracket screw and secure the card to the
computer chassis.
4. Cover the computer’s chassis.
5. Switch computer power on. If the BIOS section of your
computer’s boot program is Plug-and-Play compliant,
then at power-up the BIOS will automatically configure
any newly installed the Gigabit Ethernet Card.
NOTE: Due to a fault in some Plug-n-Play BIOS programs, it
happens occasionally that a newly installed adapter is
assigned an Interrupt Number which is already assigned to
another device. In such a case, the conflict of Interrupt
Number will cause faults in the behavior of both devices.
Then it is necessary to run the CMOS Setup utility, and
manually assign a non-conflicting Interrupt Number.
6
Connecting the Network Cable
Four pair of Cat.5 UTP or STP cable with RJ-45 connector
is required for the 32-bit PCI 10/100/1000Mbps Gigabit
Ethernet Card. You can use standard or crossover cable to
connect the switch MDI-X or MDI-II port, because the 32-
bit PCI 10/100/1000Mbps Gigabit Ethernet Card will adjust
the correct signal automatically.
Software Installation
Before you connect the 32-bit PCI 10/100/1000Mbps
Gigabit Ethernet Card to the network, you have to install
the network driver first. The driver for each networking
operating system is under a separate directory. A
HELPME.COM file under root directory lists the
information and detailed installation procedure of all the
available drivers.

7
LED INDICATORS
z10Mbps Fast Ethernet Link (10)
This indicator lights green when the Gigabit Card is
connects to 10Mbps Ethernet Network.
z100Mbps Fast Ethernet Link (100)
This indicator lights green when the Gigabit Card is
connects to 100Mbps Fast Ethernet Network.
z1000Mbps Gigabit Ethernet Link (1000)
This indicator lights green when the Gigabit Card is
connects to 1000Mbps Gigabit Ethernet Network.
zActivity (ACT)
This indicator blinking green will be transmitting or
received data on the network.
zFull-duplex mode (FDX)/ Collision (COL)
This LED indicator lights green when the Gigabit Card
is work on full duplex (FDX) mode. Otherwise, it is
blinking when collisions are occurring on the Gigabit
Card.
8
TECHNICAL SPECIFICATIONS
General
Standards IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Fast Ethernet
IEEE 802.3ab 1000Base-T Gigabit Ethernet
IEEE 802.3x Flow Control
Protocol CSMA/CD
Data Transfer Rate Ethernet: 10Mbps (half), 20Mbps (full)
Fast Ethernet: 100Mbps (half), 200Mbps (full)
Gigabit Ethernet: 1000Mbps (half), 2000Mbps (full)
Topology Star
Network Cables Ethernet: 2-pair UTP Cat. 3,4,5 , EIA/TIA- 568 STP
Fast Ethernet: 2-pair UTP Cat. 5, EIA/TIA-568 STP
Gigabit Ethernet: 4-pair UTP Cat.5, EIA/TIA-568 STP
LED Indicator 10M Link, 100M Link, 1000M Link, Activity
Full-duplex / Collision
RJ-45 Port Auto MDI-II/MDI-X port
Physical and Environmental
Power Consumption 4.3 watts. (max.)
Temperature Operating: -10°~ 40°C, Storage: -10°~ 70°C
Humidity Operating: 10% ~ 90%, Storage: 5% ~ 90%
Dimensions 59 x 120 x 15mm (W x D x H)
EMI: FCC Class B, CE Mark B, VCCI-B