TRENDnet TEG-PCITXR User manual

Copyright ©2005. All Rights Reserved. TRENDware International, Inc.
TRENDnet
TRENDware, USA
What's Next in Networking
TEG-PCITXR
Version 07.29.05
10/100/1000Mbps Gigabit Network Adapter
User’s Guide
Ghidul utilizatorului pentru
10/100/1000Mbps Gigabit Network Adapter

Table of Contents
English .................................................................................
Troubleshooting ....................................................................
1
1
3
4
7
11
11
13
14
17
21
1. Introduction ...................................................................
2. Hardware Installation ....................................................
3. Software Installation ......................................................
4. Configuring TCP/IP Protocol .........................................
1. Introducere ....................................................................
2. Instalarea Hardware ......................................................
3. Instalarea Software .......................................................
4. Configurarea TCP/IP Protocol .......................................
Românǎ ................................................................................

Congratulations on purchasing your new 10/100/1000Mbps Gigabit PCI
Adapter. This Gigabit PCI Adapter is easy to install and suitable for a 10, 100,
or 1000Mbps Ethernet network. With Gigabit performance, you can enjoy
lightening fast file transfer, uninterrupted video/audio streaming, and excellent
response time for network gaming.
Features
– IEEE 802.3, 802.3u and 802.3z compliant
– Support 32-bit 33/66Mhz PCI Local Bus Master high-speed operation of
Rev.2.1/2.2 specification
– Plug-and-Play installation
– One RJ-45 connector: Auto detection of 10Mbps Ethernet, 100Mbps Fast
Ethernet and 1000Mbps Gigabit Ethernet & Auto MDI-X
– Supports 10/100/1000Mbps Auto-negotiation operation
– Full Duplex support for 10/100/1000Mb/s data rates
– Auto MDI-II/MDI-X crossover for all three speeds
– Two LED indicators (Link, Activity) for easy diagnostic
1
1. Introduction
English UG
English

2English
Package Contents
Gigabit PCI Adapter LED
CAUTION:
Under ordinary circumstances, the 32-bit PCI 10/100/1000Mbps Gigabit
Ethernet Card will not be affected by static charge as may be received through
your body during handling of the unit. However, there are special
circumstances where you may carry an extraordinarily high static charge, and
possibly damage the card and/or your computer. It is good practice to eliminate
all static electricity by touching a ground (an unpainted metal area of your
computer chassis, for example) before performing any installations.
If any item is found missing or damaged, please contact your local reseller for
replacement.
Link (10, 100, 1000)
The Link LED indicates the connection speed of the adapter.
ACT
The ACT LED flashes when there is network activity.
User’s Guide
TEG-PCITXR 3.5" Driver Diskette
Copyright ©2005. All Rights Reserved. TRENDware International, Inc.
TRENDnet
TRENDware, USA
What's Next in Networking
TEG-PCITXR
Version 07.29.05
10/100/1000Mbps Gigabit Network Adapter
User’s Guide
Ghidul utilizatorului pentru
10/100/1000Mbps Gigabit Network Adapter

3
2. Hardware Installation
Each Gigabit Network Adapter is equipped with an RJ-45 port that
automatically adjusts the connection speed to 10Mbps, 100Mbps or 1000Mbps;
allowing your PC to attach to Ethernet, Fast Ethernet or Gigabit Ethernet
networks.
For best results, we recommend using Category 5E or higher twisted-pair RJ-
45 cable. However, if you are connecting the adapter to 10Base-T (10Mbps)
network, you can use Category 3 or higher cable. For 100Base-TX (100Mbps)
and 1000Base-T (1000Mbps) networks, please use Category 5 or higher
cables.
The hardware installation is now complete. Next step is to load the
adapter driver and configure your PC's operating system to work with the
Gigabit Adapter.
1. Power off your PC and any peripherals attached to it and unplug your PC's
power cord.
2. Remove computer's cover.
3. Open your computer and locate the PCI slot(s) on your motherboard. PCI
slots are easily identified by their beige or white color, and by the fact that
network cards fit snugly into them. Remove the metal slot cover on the back
of the PC and then insert the Gigabit Adapter into any available PCI slot.
4. Once your Gigabit Adapter is firmly in place, secure it on your PC's
chassis with a screw.
5. Replace your PC's cover.
6. Connect one end of the Category 5/5E cable to the Adapter's RJ-45 port
and another end to a Gigabit Switch or Adapter.
7. Reconnect your PC's power, then power on your computer.
If your computer has Windows Operating System, the computer would
automatically recognize the Adapter as a new hardware and start the driver
installation wizard. Follow the instructions in the Software Installation
section to install the adapter driver.
For computers with Netware Server/Client and Linux, please go to HELP
folder from the driver diskette and select the desired operating system to
view the driver installation procedures.
English
Overview
Installing Gigabit PCI Adapter into your Pcs

4
1. Start up your computer.
2. Windows 98 automatically detects the presence of the Gigabit adapter.
3. Insert the Driver Diskette into your floppy drive when the Add New
Hardware Wizard window appears and click Next.
4. Select Search for the best driver for your device (Recommended). Click
Next.
5. Select Specify a location, type A:\win98 in the drop down box and click
Next (assuming A: drive is the floppy drive).
6. Windows is now ready to install the Gigabit Adapter driver. Click Next to
continue.
7. Windows will begin copying the driver files to your PC.
At this point, the installation may require files from your Windows 98 CD-
ROM. When this happens, insert your Windows 98 CD-ROM into your CD-
ROM drive and select CD-ROM drive (on the screen) to load the files.
8. After Windows has finished copying the files, it will prompt you to restart
your PC. Remove the diskette and CD-ROM and click YES to restart the
PC.
3. Software Installation
English
Installing the Driver for Windows 98

5English
1. Start up your computer.
2. Windows ME automatically detects the presence of the Gigabit adapter.
3. Insert the Driver Diskette into your floppy drive when the "Add New
Hardware Wizard" window appears and click Next.
4. Select Specify the location of the driver (Advanced). Click Next.
5. Select Search for the best driver for your device (Recommended) and
check the Specify a location, enter A:\winme (assuming A: drive is the
floppy drive), and click Next.
6. Windows is now ready to install the Gigabit Adapter driver. Click Next to
continue.
7. Windows will begin copying the driver files to your PC. At this point, the
installation may require files from your Windows ME CD-ROM. When this
happens, insert your Windows ME CD-ROM into your CD-ROM drive and
select CD-ROM drive (on the screen) to load the files.
8. After Windows has finished copying the files, it will prompt you to restart
your PC. Remove the diskette and CD-ROM and click YES to restart the
PC.
1. Start up your computer. You must have administrative rights to perform
the installation.
2. The Found New Hardware window appears
3. Insert the Driver Diskette into your floppy drive
4. Select Search for a suitable driver for my device (Recommended) and
click Next.
5. At the Locate Driver Files dialog box, select Specify a location, click Next,
type A:\win2k and click OK. The Driver file search results dialog box
appears. Click Next to continue.
6. At Microsoft's digital Signature window, click YES to continue the
installation.
7. Click Finish to complete the driver installation.
Installing the Driver for Windows ME
Installing the Driver for Windows 2000

6English
1. Start up your computer. You must have administrative rights to perform
the installation.
2. The Found New Hardware window appears
3. Insert the Driver Diskette into your floppy drive
4. Select Install from a list or specific location option and click Next.
5. Select Search for the best driver in these locations and select Include
these location option and type A:\winxp and click OK. The Driver file
search results dialog box appears. Click Next to continue.
6. At Microsoft's digital Signature window, click Continue Anyway to continue
the installation.
7. Click Finish to complete the driver installation.
After the driver files are loaded for Windows, the Gigabit network adapter is
now ready for operation. If your network requires configuring TCP/IP protocol,
please proceed to configure the PC's TCP/IP protocol to communicate with the
existing network.
Installing the Driver for Windows XP

7English
4. Configuring TCP/IP Protocol
1. On the Desktop, right-click My Network Places and click Properties. Then,
right-click Wireless Network Connection and click Properties; the Network
Connection Properties Window will appear
2. Under the General tab, select Internet Protocol (TCP/IP) and click the
Properties button; the Internet Protocol (TCP/IP) Properties Window will
appear.
Configure TCP/IP protocol settings to match your network.
1. Select the Obtain an IP address automatically option.
2. Select the Obtain DNS server address automatically option.
3. Click OK to save the settings.
Windows 2000/XP
i.For DHCP IP address Setup (this should work for
most network environments)

8
1. Select the Use the following IP address option and enter the IP, Subnet
Mask, and Default gateway addresses.
2. Select the Use the following DNS server address option and enter DNS
addresses.
1. On the Desktop, right-click Network Neighborhood and click Properties.
Then, right-click Wireless Network Connection and click Properties; the
Wireless Network Connection Properties Window will appear.
2. Under Configuration tab, select Realtek RTL 8169/8110 Gigabit Ethernet
NIC (TCP/IP protocol) and click on the Properties button; the TCP/IP
Protocol Properties Window will appear
ii.For Static IP address Setup
For Windows 98/ME users
3. Click OK to save the settings.
English

9
i.For DHCP IP address Setup (this should work for
most network environments)
ii.For Static IP address Setup
1. Select the Obtain an IP address automatically option.
1. Select the Specify an IP address option, and enter the IP and Subnet Mask
addresses.
English

10
Windows 2000/XP:
go to "start", select "run", type in cmd, then click ok. At the command prompt
(C:\), type in ipconfig/all and hit "Enter".
Windows 98/ME:
go to "Start", select "Run", type in winipcfg, then click "OK". From the drop-
down menu, select the name of the network adapter (not the PPP Adapter).
Ping Command:
If you know a networked device's IP address, in the command prompt (c:\),
type in ping xxx.xxx.xxx.xxx (where xxx.xxx.xxx.xxx is the device's IP
address) and hit "Enter". If you see replies from this IP address, your computer
should be able to communicate with this device.
i.Checking the Adapter’s IP Address
English
2. Select Gateway option and enter the Gateway IP address
3. Select DNS Configuration and add the DNS IP address and click OK to
finish.
Note: If your network has a DHCP Server (e.g. Internet Router), for ease
of configuration, please enable it and setup the network adapter with
DHCP IP configuration. After the adapter connects to the network, it will
receive the addresses automatically.

11
1. Introducere
Felicitari pentru achizitionarea Adaptorului PCI 10/100/1000Mbps Gigabit .
Acesta este usor de instalat si si potrivit unei retele Ethernet de 10, 100, sau
1000Mbps. Cu tehnologia Gigabit va puteti bucura de viteza rapida de transfer
a datelor, streaming video/audio neintrerupt , si un raspuns excelent in ceea ce
prievste jocurile
Caracteristici
– IEEE 802.3, 802.3 sau 802.3z
– Suporta Local Bus Master 32-bit 33/66Mhz PCI , Rev.2.1/2.2
– Instalare Plug-and-Play
– Un conector RJ-45 : Auto detectare 10Mbps Ethernet, 100Mbps Fast
Ethernet si 1000Mbps Gigabit Ethernet & Auto MDI-X
– Suporta 10/100/1000Mbps operare Auto-negociere
– Suporta Full Duplex pentru rate de date 10/100/1000Mb/s
– Auto MDI-II/MDI-X pentru toate cele 3 viteze
– Doua LEDuri (Link, Activity) pentru diagnosticare rapida
Românǎ QIG
Românǎ

12
Continutul Pachetului
Gigabit PCI LED Adaptor
ATENTIE :
In conditii normale, Cardul Ethernet 32-bit PCI 10/100/1000Mbps Gigabit nu va
fi afectat de incarcatura statica receptionata din corpul dvs. Totusi, exista
circumstante speciale in care purtati o incarcatura statica iesita din comun
putand astfel deteriora cardul si/sau calculatorul. Este indicat sa eliminati
energia atingand spre exemplu o portiune de metal de la computerul dvs ,
inainte de a incepe orice proces de instalare.
Daca un articol lipseste sau este deteriorat, va rugam sa contactati
distribuitorul pentru inlocuire.
Link (10, 100, 1000)
LEDul Link indica viteza conexiunii a adaptorului.
ACT
LEDul ACT clipeste cand exista activitate a retelei.
Ghidul utilizatorului
TEG-PCITXR 3.5” Driver Disketa
Românǎ
Copyright ©2005. All Rights Reserved. TRENDware International, Inc.
TRENDnet
TRENDware, USA
What's Next in Networking
TEG-PCITXR
Version 07.29.05
10/100/1000Mbps Gigabit Network Adapter
User’s Guide
Ghidul utilizatorului pentru
10/100/1000Mbps Gigabit Network Adapter

13
2. Instalarea Hardware
Fiecare Adaptor de Retea Gigabit este echipat cu un port RJ-45 care ajusteaza
automat viteza conexiunii la 10Mbps, 100Mbps sau 1000Mbps; permitand
PCului dvs sa se ataseze la retele Ethernet, Fast Ethernet sau Gigabit Ethernet
.
Pentru cele mai bune rezultate, va recomandam folosirea Categoriei 5E de
cablu sau perechii RJ-45. Cu toate acestea, daca vreti a conecta adaptorul la
reteaua 10Base-T (10Mbps), puteti folosi cablul Categoria 3 sau mai mult.
Pentru retelele 100Base-TX (100Mbps) si 1000Base-T (1000Mbps), va rugam
folositi cablul din Categoria 5 sau mai mult.
Românǎ
Vedere de Ansamblu
1. Opriti PCul si orice alte periferice atasate acestuia, si deconectati cablul de
alimentare .
2. Indepartati carcasa PCului.
3. Localizati slotul/sloturile PCI de pe placa de baza. Acestea pot fi usor
identificate datorita culorii bej sau alb, si datorita faptului ca placile de retea
intra perfect in ele. Indepartati “coperta” de metal a slotului din spatele
PCului iar apoi introduceti Adaptorul in slotul PCI.
4. Odata plasat corect adaptorul , fixati-l cu un surub .
5. Asezati la loc carcasa PCului.
6. Conectati un capat al cablului Categoria 5 la portul RJ-45 al Adaptorului,
iar celalalt capat la un Switch sau Adaptor Gigabit
7. Reconectati cablul de alimentare ,si porniti calculatorul.
Daca dispuneti de Windows ca sistem de operare, calculatorul va
recunoaste automat Adaptorul ca fiind hardware nou si va incepe instalarea
driverului. Urmatii instructiunile din sectiunea Software Installation pentru a
instala driverul .
Pentru computerele ce dispun de Netware Server/Client si Linux, va rugam
accesati directorul HELP de pe disketa driver si selectati sistemul de
operare dorit , pentru a vizualiza procedurile de instalare ale driverelor.
Instalarea Adaptorului Gigabit PCI in PCul dvs
Inslarea hardware este acum completa. Urmatorul pas este incarcarea
driverului Adaptorului si configurarea sistemului de operare de pe PC
pentru a lucra cu Adaptorul Gigabit.

14 Românǎ
3. Instalarea Software
Instalarea Driverului pt Windows 98
1. Porniti PCul.
2. Windows 98 va dectecta automat prezenta adaptorului Gigabit.
3. Introduceti Disketa Driver in unitatea floppy cand apare fereastra Add
New Hardware iar apoi dati click pe Next.
4. Selectati Search for the best driver for your device (Recommended).Dati
Click pe Next.
5. Selectati Specify a location, tastati A:\win98 in casuta iar apoi dati click
pe Next (presupunand ca unitatea A: este cea destinata disketei de tip
floppy).
6. Windows este acum gata pentru insalarea driverului.Dati click pe Next
pentru a continua.
7. Windows va incepe sa copieze fisierele driverului pe PC.
In acest moment, instalarea poate necesita fisiere de pe CDul Windows 98.
Cand acest lucru se iveste, introduceti CDul Windows 98, alegeti unitatea
CD-ROM (de pe ecran) pentru a incarca fisierele.
8. Dupa ce Windows a terminat de copierea fisierelor, va va cere sa restartati
PCul. Scoateti disketa si CDul si alegeti YES pentru a restarta PCul.

15 Românǎ
1. Porniti PCul.
2. Windows ME va dectecta automat prezenta adaptorului Gigabit.
3. Introduceti Disketa Driver in unitatea floppy cand apare fereastra Add
New Hardware iar apoi dati click pe Next.
4. Selectati Specify the location of the driver (Advanced). Dati Click pe
Next.
5. Selectati Search for the best driver for your device (Recommended) si
alegeti e Specify a location, tastati A:\winme (presupunand ca unitatea A:
este cea destinata disketei de tip floppy) si dati click pe Next.
6. Windows este acum gata pentru instalarea driveruluir. Dati Click ep Next
pentru a continua.
7. Windows va incepe sa copieze fisierele driverului pe PC.
In acest moment, instalarea poate necesita fisiere de pe CDul Windows 98.
Cand acest lucru se iveste, introduceti CDul Windows 98, alegeti unitatea
CD-ROM (de pe ecran) pentru a incarca fisierele.
8. Dupa ce Windows a terminat de copierea fisierelor, va va cere sa restartati
PCul. Scoateti disketa si CDul si alegeti YES pentru a restarta PCul.
Instalarea Driverului Windows ME
1. Porniti PCul. Trebuie sa aveti drapturi administrative pentru a efectua
aceasta instalare.
2. Va aparea fereastra Found New Hardware.
3. Introduceti Disketa Driver in uniatea floppy.
4. Selectati Search for a suitable driver for my device (Recommended) si
dati pe Next.
5. Din casuta” Locate Driver Files”, selectati Specify a location, dati click pe
Next,si tastati A:\win2k si dati click pe OK. Va aparea casuta cu rezultatele
cautarii fisierelor Driver. DatiClick pe Next pentru a continua.
6. In fereastra Microsoft's digital Signature (semnatura digitale) dati click pe
YES pentru a continua instalarea.
7. Dati Click pe Finish pentru a completa instalarea driverului.
Instalarea Driverului pentru Windows 2000

16 Românǎ
1. Porniti PCul. Trebuie sa aveti drapturi administrative pentru a efectua
aceasta instalare.
2. The Found New Hardware window appears
3. Introduceti Disketa Driver in uniatea floppy
4. Selectati Search for a suitable driver for my device (Recommended) si
dati pe Next.
5. Selectati Search for the best driver in these locations si selectati
optiunea Include these location si tastati A:\winxp si dati click pe OK. Va
aparea casutia cu rzultatele cautarii fisierelor Driver. Dati Click pe Next
pentru a continua.
6. In fereastra Microsoft's digital Signature (semnatura digitale) dati click pe
Continue Anyway pentru a continua instalarea.
7. Dati Click pe Finish pentru a completa instalarea driverului.
Dupa incarcarea fisierelor driver, adaptorul Gigabit de retea este gata pentru a
fi utilizat. Daca reteaua dvs necesita configurarea “TCP/IP protocol”, va rugam
configurati “ TCP/IP protocol” pentru asigurarea comunicarii cu reteaua
existenta.
Instalarea Driverului pentru Windows XP

17 Românǎ
4. Configurarea TCP/IP Protocol
1. Dati click-dreapta pe My Network Places din Desktop > selectati
Properties > click-dreapta pe Local Area Connection > selectati
Properties, va aparea fereastra “Network Connection Properties”.
2. Din tab-ul General , selectati Internet Protocol (TCP/IP) > dati click pe
butonul Properties ,va aparea fereastra Internet Protocol (TCP/IP)
Properties.
Configurati setarile TCP/IP protocol pentru a se potrivi cu reteaua dvs.
1. Selectati optiunea Obtain an IP address automatically.
2. Selectati optiunea Obtain DNS server address automatically .
3. Dati Click pe OK pentru a termina.
Windows 2000/XP
i.Pentru setarea adresei DHCP IP (Ar trebui sa
mearga in cazul majoritatii mediilor de retea)

18 Românǎ
1. Selectati optiunea Use the following IP address si tastati adresa IP, si
adresele Subnet Mask si Default gateway .
2. Selectati optiunea Use the following DNS server address si tastati
adresele DNS.
1. In Desktop, dati click-dreapta pe Network Neighborhood > selectati
Properties > dati click-dreapta pe Local Area Connection > selectati
Properties, va aparea fereastra “ Network Connection Properties”.
2. Din tab-ul Configuration , selectati Realtek RTL 8169/8110 Gigabit
Ethernet NIC (TCP/IP protocol) > dati click pe butonul Properties ,va
aparea fereastra TCP/IP Protocol Properties.
ii. Pentru setarea adresei Static IP
Pentru utilizatorii Windows 98/ME
3. Dati Click pe OK pentru a termina.