TRENDnet TFM-CF56 User manual

TFM-CF56
CompactFlash 56K Modem Card
Quick Installation Guide
For Pocket PC

—2—
The Federal Communications Commission Statement
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

—3—
You are cautioned that changes or modifications not expressly
approved by the party responsible for compliance could void your
authority to operate the equipment.
COPYRIGHTS & TRADEMARKS
Microsoft, Windows and the Windows logo are registered
trademarks of the Microsoft Corporation. All other trademarks
and brand names are the property of their respective proprietors.

—4—
Contents
?? Package Contents ……………………………… 5
?? Hardware Installation ……………………………. 6
?? Configuring a Modem Connection on Your Pocket
PC …………………………………………………… 7
?? Setting up your Pocket PC for POP3 Email…… 11
?? Connecting to ActiveSync using a Modem…… 14

—5—
Package Contents
Please ensure that the following items are included in your package. If
any items are missing contact your dealer.
?? CompactFlash 56K Modem Card
?? Analog Phone Cable
?? Quick Installation Guide

—6—
Hardware Installation
1. Firmly insert the CF Modem card
into the CompactFlash slot on
top
of your pocket PC with the 50-
pin
connector facing the
CompactFlash slot. You will hear
a click when firmly connected.
2. Please Press YES to skip the
warning message.
3. Connect the analog phone
cable to RJ-11 of the CF
modem. And insert the other
end of the analog phone cable
into a standard telephone
outlet.

—7—
Configuring a Modem Connection on Your Pocket PC
1. On your Pocket PC, tap the Start button
and choose Settings.
2. Tap the Connections tab and choose
Modem icon. Note: Consult with your
network administrator for specific
settings.
3. Tap New Connection…

—8—
4. Type in a name in the Enter a name
for the connection text box.
5. Choose CompactFlash56K
Modem from the Select a modem
list.
6. Choose Baud Rate for your CF
modem. For example: 115200. Tap
the Advanced button.
7. Tap the Name Servers tab.
8. According to your ISP account,
input appropriate address if
necessary.
9. Tap OK at top left to continue.

—9—
10. Tap the Next button.
11. Type in your local ISP access number.
12. Tap Next to continue.

—10 —
13. Tap Finish to finish.

—11 —
Setting up your Pocket PC for POP3 Email
1. Launch the Inbox from your Pocket
PC. TapServices, followed byNew
Service from the menu. TapNext
2. In the Server Field, enter the
incoming mail server (usually a POP3)
and your User ID and Password. If you
are having problems, please contact
your ISP. Tap Next.

—12 —
3. Leave the Domainname blank unless
you are connecting to a Microsoft NT
server. The SMTP server will usually be
the same as your POP3 server but check
with your ISP to make sure. The return
address is your email address. TapNext.
4. These are email options. Choose those
options that you wish to use. TapNext.

—13 —
5. The last screen has options for email
retrieval. You can select the options on
how you view mail. If you choose Get
Full Copy of Messages, you download the
entire email. If you choose Get Message
Headers Only, you download only the
summary of the email. Choose the amount
of lines you wish to download. If you use
Microsoft Outlook, check Get Message
Requests if you want to retrieve and
respond to meeting requests. Check Get
File Attachments if you wish to download
file attachments. This may slowdown your
download time.

—14 —
Connecting to ActiveSync using a Modem
Before you begin:
?? Setup a partnership between your device and the desktop
computer using serial cable, cradle, or infrared connection.
See Microsoft ActiveSync Help if you have more questions.
?? If your computer is running Windows NT 4.0, you need to
install Remote Access Service (RAS). RAS is included with
Windows 2000.
?? If you are running Windows 95, you need to install Dial-Up
Networking Upgrade (DUN) 1.3 or later.
?? Install an internal or external modem
Configuring RAS, DUN, and modem equipment to work with
ActiveSync

—15 —
If your computer is running Windows NT 4.0 or Windows 2000, you
will need to configure RAS to work with ActiveSync. If your
computer is running Windows 95/98, you will need to configure DUN
to work with ActiveSync.
Configure RAS and modem equipment on Windows NT 4.0
There are three steps:
1. Install network components.
2. Configure RAS.
3. Configure the user account.
Install network components
1. Click Start, Settings, and thenControl Panel.
2. Double-click the Network icon. If you see a Network
Configuration Wizard, then continue below. Otherwise, skip to the
next section because networking is already installed.
3. In the Network Configuration box, click Yes.

—16 —
4. Select Wired to the network, clear Remote access to the
network, and then click Next.
5. Click Select from list.
6.In the Network Adapters box, selectMS Loopback Adapter and
click Next.
7. In the Network Protocols box, selectTCP/IP Protocol and clear
all other options.
8. Click Next three times to start installing the selected components.
9. In the Windows NT Setupbox, enter the directory where your
Windows NT source files are located and then click Continue.
10. In the MS Loopback Adapter Card Setupdialog box, click
Continue. The default frame type will be selected.
11. In the TCP/IP Setupdialog box, click No when asked to use
DHCP.
12. In the Microsoft TCP/IP Properties box, click the IP Address
tab.

—17 —
13. Make sure MS Loopback Adapter is selected.
14. Click Specify an IP Address and in the IP Address box, enter
1.1.1.1.
15. In the Subnet Mask box, enter 0.255.255.255.
16. Make sure the Default Gateway box is cleared.
17. Click Next on the next three dialog boxes, and then click Finish to
complete the Networking Wizard.
18. Restart your desktop computer.
Configuring Remote Access Server (RAS)
1. Click Start, Settings, and thenControl Panel.
2. Double-click the Network icon. Then click the Services tab.
3. From the Network Services list, selectRemote Access Service,
and then click Properties. If Remote Access Service is not listed,
perform the following steps; otherwise, proceed to step 9:

—18 —
4. Click the Services tab, and then click Add.
5. Select Remote Access Service from the list, and then click OK.
6. Provide your Windows NT Setup disks if instructed to.
7. In the Add RAS Device, select your modem.
8. Click OK, then leave the Remote Access Setup dialog box open.
9. In the Remote Access Setup, select your modem.
10. Click Configure, select Receive calls only, and then click OK.
11. In the Remote Access Setupdialog box, click Network.
12. In the Network Configuration dialog box, clear Require data
encryption.
13. Under Server Settings, select TCP/IP, and then click Configure.
14. Select This computer onlyand selectUse static address pool.

—19 —
15. In the Beginbox, enter 192.168.55.100. In the Endbox, enter
192.168.55.112.
16. Clear Allow remote clients to request a predetermined IP
address.
17. Accept the default (recommended) responses for any messages that
appear.
18. Click Continue, and then click Close.
19. Restart your desktop computer when prompted and reinstall any
Windows NT 4.0 Service Packs.
Configure your user account
1. Click Start, Programs, Administrative Tools, and thenUser
Manager.
2. In the top list box, double-click your user account.
3. Clear Account Disabled, and then clear User Must Change
Password at Next Logon.

—20 —
4. Select Password Never Expires.
5. Delete any passwords in the Password and Confirm Password
boxes.
6. Click Dialing.
7. Select Grant dialing permission to user and No Call Back.
Configuring RAS on Windows 2000
Configure the desktop computer for incoming connections
1. Click Start, Settings, and thenControl Panel.
2. Double-click the Network and Dial-up Connections icon.
3. Click Make New Connection.
4. Select Accept incoming connectionsand click Next.
5. Select the modem from the list of devices, and click Next.