TRENDnet TE100-S810Fi - Switch User manual

1

1.
Introduction
In the modern society, communication and sharing information is
essential to our lifestyle. Computer networks have proven to be one of
the fastest methods of communication.
The 8-port Management Switch series are compact desktop size
switches which are ideal solutions for SOHO (Small Office or Home
Office) network user. It provides wire-speed, Fast Ethernet switching
function that allows high-performance, low-cost connection. The
Switches feature a store-and-forward switching and it can auto-learn
and store source address on an 8K-entry MAC address table.
Figure 1-1. The 8port Management Switch
The Switches provides 8 switched auto-sensing 10/100 Mbps RJ-45
Ethernet portsplus one 100Base-FX fiber port. The Switch will
automatically detects the speed of the device that you plug into it to
allow you to use both 10 and 100Mbps device. The 10Mbps
bandwidth will accommodate 10Mbps workgroup hubs while
simultaneously providing the 100Mbps bandwidth needed to
accommodate multimedia applications. In addition, each RJ-45 port
supports Auto-MDIX function.
TheTE100-S810Fi couples with one 100Base-FX fiber port. There are
4 types of fiber connectors available for the convenience of your
connectivity on the Switch. These fiber connectors are
SC/MT-RJ/VF-45 (multi-mode fiber) and SC (single-mode fiber).

3
However, the fiber port can be used to connect to a remote side up to
2 Kilometers (multi-mode fiber) or 15~60 kilometers (SC single- mode
fiber) away.
With their build-in Web-based Management, managing and
configuring the TE100-S810Fi becomes easier. From cabinet
management to port-level control and monitoring, you can visually
configure and manage your network via Web Browser. Just click your
mouse instead of typing command strings. However, the
TE100-S810Fi can also be managed via Telnet, Console, or SNMP
Management.
Features
Conforms to IEEE 802.3, 802.3u, and 802.3x Ethernet
Standards
8x auto-sensing 10/100Mbps Ethernet RJ-45 ports
Automatic MDI/MDIX crossover for each 10Base-T/
100Base-TX port
1 Fixed 100Mbps Fiber port (SC/SC single-mode/MT-RJ
/VF-45 connector ) [ for 8TP+1Fiber series only ]
One Console port on the rear side for port-based VLAN &
Trunking Configuration
Half-duplex mode for backpressure, and Full-duplex for flow
control
Store-and-forward switching architecture
Automatic address learning, address migration
8K-entry MAC address table
2Mbit memory buffer sharing
Performs non-blocking full wire speed
LED-indicators for Power, 100M, LK/ACT, FD/COL
10-inch Desktop size design

Intelligent Management Features
Web-based management
SNMP network management
Console and Telnet management
Port Base VLAN and IEEE 802.1q Tag VLAN, and VLAN
group up to 256 , VLAN ID up to 4095.
IEEE 802.3 ad LACP, Trunk group up to 4 and members up
to 8 port (8 10/100TX plus one uplink port model).
IEEE 802.1d Spanning Tree
MIB II (RFC1213) supported
IP Multi-cast, IGMP Snooping
IEEE802.1p for Global system, each port includes 2 queues
for high or low priority.
Port Mirror, Broadcast Filter, Static MACAddress, Port
Security and GVRP supported.

5
Package Contents
Unpack the contents of the TE100-S810Fi and verify them against the
checklist below.
TE100-S810Fi
Power Cord
Four Rubber Feet
RS-232 cable
User Guide
TE100-S810Fi Power Cord
Rubber Feet RS-232 cable
Figure 1-2. Package Contents
Compare the contents of your TE100-S810Fi package with the
standard checklist above. IF any item is missing or damaged, please
contact your local dealer for service.

Management Methods
The TE100-S810Fi series supports following management methods:
Console and Telnet Management
Web-based Management
SNMP Network Management
Console and Telnet Management
Console Management is done through the RS-232 Console Port.
Managing the TE100-S810Fi in this method requires a direct
connection between PC and the TE100-S810Fi. While Telnet
management is done over the network. Once the TE100-S810Fi is on
the network, you can use Telnet to Log in and change the
configuration.
Web-based Management
The Switch provides an embedded HTML web site residing in flash
memory. It offers advanced management features and allow users to
manage the TE100-S810Fi from anywhere on the network through a
standard browser such as Microsoft Internet Explorer.
SNMP Network Management
SNMP ( Simple Network Management Protocol ) provides a
means to monitor and control network device, and to manage
configurations, statistic collection, performance, and security.

7
2.
Hardware Description
This section mainly describes the hardware of the TE100-S810Fi
series. The Switches is a compact switch ( 10 inches ) with 8x
auto-sensing 10/100Mbps Ethernet RJ-45 ports ( 8TP Management
Switch ) plus one 100Base-FX fiber port (TE100-S810Fi ).
The physical dimensions of the TE100-S810Fi are: 250mmx
132mmx 37mm ( Lx Wx H )
Front Panel
The Front Panel of the TE100-S810Fi series consist of 8x
auto-sensing 10/100Mbps Ethernet RJ-45 ports ( automatic
MDI/MDIX ), one 100Base-FX fiber port (TE100-S810Fi ) and the
LED indicators are also located on the frond panel of the switch.
Figure 2-1. The Front Panel of the TE100-S810Fi
The Front Panel of the TE100-S810Fi is displayed as below. There
are four types of fiber connectors available for the convenience of
your connectivity. These fiber connector is SC multi-mode.

Figure 2-2. The Front Panel of the TE100-S810Fi
RJ-45 Ports (Auto MDI/MDIX ): Eight 10/100 auto- sensing
for 10Base-T or 100Base-TX connections.
[ In general, MDI means connecting to another Hub or Switch
while MDIX means connecting to a workstation or PC.
Therefore, Auto MDI/MDIX means that you can connect to
another Switch or workstation without changing
non-crossover or crossover cabling. ]
100Base-FX Fiber Port: The distance for fiber cabling can
be extended up to 2 kilometers.
LED Indicators
Figure 2-6. LED Indicators
There are three LED-Indicators (100M, LNK/ACT, FDX/COL) for each
UTP port. The following table provides descriptions of the LED
statuses and meaning. They provide a real-time indication of
systematic operation status.

9
LED
Status
Color
Description
Power
On
Green
Power On
100M
On
Green
The port is operating at the speed of
100Mbps.
Off
In 10Mbps mode or no device attached
LNK /
ACT
On
Green
The port is successfully connecting
with the device.
Blinks
Green
The port is receiving or transmitting
data.
Off
No device attached.
FDX /
COL
On
Orange
The port is operating in Full-duplex
mode.
Blinks
Orange
Collision of Packets occurs in the port.
Off
Half-duplex mode or no device
attached.
Table 2-1. The description of LED Indicator
Rear Panel
The Console port and 3-pronged power plug are located at the Rear
Panel of the TE100-S810Fi as shown in Figure 2-8. The Switches will
work with AC in the range 100-240V AC, 50-60Hz.
Figure 2-7 The Rear Panel of the TE100-S810Fi

Console Port : Console management can be done through the
Console Port. It requires a direct connection between the Switch and
an end station ( PC ) via a RS-232 cable.
Desktop Installation
Set the switch on a sufficiently large flat space with a power outlet
nearby. The surface where you put your Switch should be clean,
smooth, level, and sturdy.
Make sure there is enough clearance around the Switch to allow
attachment of cables, power cord and air circulation.
Attaching Rubber Feet
A. Make sure mounting surface on the bottom of the Switch is grease
and dust free.
B. Remove adhesive backing from your Rubber Feet.
C. Apply the Rubber Feet to each corner on the bottom of the Switch.
These footpads can prevent the Switch from shock/vibration.
Figure 2-8. Attaching Rubber Feet to each corner on the bottom of the
Switch