TRENDnet TEG-424WS User manual

24-Port 10/100Mbps Web Smart Switch
w/4 Gigabit Ports and 2 Mini-GBIC Slots
TEG-424WS
1.03
ŸQuick Installation Guide (1)
ŸTroubleshooting (3)

1
Minimum Requirements
Package Contents
If any of the above contents are missing, please contact your reseller.
1. Before You Start
ŸWeb Browser: Internet Explorer (6.0 or above)
ŸComputer with network adapter installed
ŸCat. 5, Cat. 5e or Cat.6 RJ-45 network cable
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
TEG-424WS
Multi-Language Quick Installation Guide
CD-ROM (Utility and User Guide)
Power Cord
Rack Mount Kit
Optional Equipment
ŸStandard 19” Rack
ŸMini-GBIC Modules (e.g. TEG-MGBSX, TEG-MGBS10, TEG-MGBS40,
TEG-MGBS80, TEG-MGBS10D35, TEG-MGBS40D35)
2. Hardware Installation
Note:
1. After hardware installation is complete, use the Web Smart Switch
Management Utility to configure the TEG-424WS. To access the Web Smart
Switch Management Utility, open your web browser, and enter the default IP
Address http://192.168.0.1 and default password "admin". Make sure your
computer and the TEG-424WS are configured to the same network segment.
2. The Mini-GBIC slots are shared with Gigabit Ethernet ports 25 and 26. When
the Mini-GBIC slots are in use, Gigabit Ethernet ports 25 and 26 are disabled.
3. If you would like to easily discover all the Web Management Switches on the
network, assign IP Address, change the password, and upgrade new
firmware, then install the Web Smart Switch Management Utility. Follow the
steps provided on the user's guide.

2
2. Connect a RJ-45 network cable from the computer to an available Ethernet
port of the TEG-424WS.
1. Connect the Power Cord to the TEG-424WS and then to a power outlet.
For more information regarding the Web Smart Switch Management Utility
configuration and advanced settings, please refer to the User's Guide included
on the provided CD-ROM or TRENDnet's website at www.trendnet.com

Troubleshooting
1. After connecting the TEG-424WS to a power outlet, the LEDs do not turn
on.
1. Check the connection of the power cord to the TEG-424WS and the power
outlet.
2. Check that the power outlet is receiving power.
2. When I access the TEG-424WS using a web browser, I get a screen that
tells me “only one user can login”. What should I do?
Another computer is configuring the TEG-424WS. Please wait until the user
logs off. If the other user has already logged off and you still get the same
screen, then disconnect the power cord from the TEG-424WS, wait for 5
seconds, reconnect the power cord to the TEG-424WS, allow 5 seconds for
the switch to power on, and then attempt to access the web configuration
page again.
3. I forgot the administration password. How do I reset my TEG-424WS?
Press on the reset button using a pen or paperclip for 10 seconds. The default
password is admin. Note: The default password is case sensitive.
4. When I connect a computer to the Switch's Gigabit Ethernet port, I am
not getting Gigabit speeds. What should I do?
1. Check the LEDs on the Switch. When the 1000Mbps LED is off, the
computer's connection speed is 10 or 100Mbps.
2. Make sure that you have a Gigabit Ethernet adapter installed.
3. Make sure to use a Cat. 5e or Cat. 6 Ethernet cable. Some Cat.5 cables
are not rated to run in Gigabit.
If you still encounter problems or have any questions regarding the
TEG-424WS, please refer to the User's Guide included on the provided
CD-ROM or contact Trendnet's Technical Support Department.
3

TRENDnet
20675 Manhattan Place
Torrance, CA 90501. USA
Copyright ©2011. All Rights Reserved. TRENDnet.