TRENDnet TEW-733GR User manual

© Copyright 2013 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide Table of Contents
i

© Copyright 2013 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide Table of Contents
ii
Contents
Product Overview ...........................................................................4
Package Contents .......................................................................................................... 4
Features ......................................................................................................................... 4
Product Hardware Features........................................................................................... 5
Application Diagram ...................................................................................................... 7
Basic Router Setup ..........................................................................7
Creating a Home Network ............................................................................................. 7
Router Installation ......................................................................................................... 8
Connect additional wired devices to your network..................................................... 10
Wireless Networking and Security .................................................11
How to choose the type of security for your wireless network .................................. 11
Secure your wireless network ..................................................................................... 12
Connect wireless devices to your router ..................................................................... 14
Connect wireless devices using WPS ........................................................................... 15
Basic wireless settings ................................................................................................. 16
Guest Zone................................................................................................................... 18
Steps to improve wireless connectivity ....................................................................... 19
Advanced wireless settings.......................................................................................... 19
Access Control Filters ....................................................................20
Access control basics ................................................................................................... 20
MAC address filters ................................................................................................. 20
Parental Controls/URL Filters .................................................................................. 20
Protocol/IP filters .................................................................................................... 21
Advanced Router Setup.................................................................22
Access your router management page........................................................................ 22
Change your router login password ............................................................................ 22
Change your device name ........................................................................................... 22
Manually configure your Internet connection ............................................................ 23
Clone a MAC address................................................................................................... 23
IPv6 Internet Connection Settings............................................................................... 23
Auto Detection ........................................................................................................ 24
Static IPv6................................................................................................................ 24
Auto-configuration.................................................................................................. 25
PPPoE ...................................................................................................................... 25
IPv6 in IPv4 Tunnel.................................................................................................. 26
6to4 ......................................................................................................................... 27
6rd........................................................................................................................... 27
Link-local Only ......................................................................................................... 27
LAN IPv6 Address Settings....................................................................................... 27
Change your router IP address.................................................................................... 28
Set up the DHCP server on your router....................................................................... 28
Set up DHCP reservation ............................................................................................. 29
Enable/disable UPnP on your router........................................................................... 30
Allow/deny VPN connections through your router..................................................... 30
Allow/deny multicast streaming.................................................................................. 30
Enable SPI .................................................................................................................... 31
Identify your network on the Internet ........................................................................ 31
Set your router date and time..................................................................................... 32
Create schedules ......................................................................................................... 32
Open a device on your network to the Internet.......................................................... 33
DMZ......................................................................................................................... 33
Virtual Server .......................................................................................................... 34

© Copyright 2013 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide Table of Contents
iii
Port Forwarding ...................................................................................................... 35
Application Rules..................................................................................................... 36
Allow remote access to your router management page ............................................. 36
Internet Bandwidth Control......................................................................................... 37
Add static routes to your router.................................................................................. 37
Router Maintenance & Monitoring................................................38
Reset your router to factory defaults .......................................................................... 38
Router Default Settings ............................................................................................... 38
Backup and restore your router configuration settings .............................................. 39
Upgrade your router firmware .................................................................................... 39
Restart your router ...................................................................................................... 40
Check connectivity using the router management page............................................. 40
Check the router system information.......................................................................... 41
View your router log .................................................................................................... 43
Send router logs to your email .................................................................................... 44
Setup a syslog server from router ............................................................................... 45
View your router packet statistics ............................................................................... 45
View your router active sessions ................................................................................. 46
View your routing table ............................................................................................... 46
View devices connected to your router....................................................................... 47
View wireless devices connected to your router......................................................... 47
View your router’s IPv6 network information............................................................. 47
Router Management Page Structure .............................................48
Technical Specifications.................................................................49
Troubleshooting............................................................................50
Appendix ......................................................................................51

© Copyright 2012 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide TEW-733GR
4
Product Overview
TEW-733GR
Package Contents
In addition to your router, the package includes:
•Multi-Language Quick Installation Guide
•CD-ROM (User’s Guide)
•Network cable (1.5 m / 5 ft.)
•Power adapter (12V DC, 1A)
If any package contents are missing or damaged, please contact the retail store, online
retailer, or reseller/distributor from which the product was purchased.
Features
TRENDnet’s N300 Wireless Gigabit Router, model TEW-733GR, offers
proven high performance 300 Mbps wireless n networking and gigabit
wired Ethernet ports. Embedded GREENnet technology reduces power
consumption by up to 50%. For your security this router comes pre-
encrypted and features a guest network. Seamlessly stream HD video
with this powerful router.
Ease of Use
Easy Setup
Get up and running in minutes with the intuitive guided setup
One Touch Connection
Securely connect to the router at the touch of the Wi-Fi Protected Setup
(WPS) button
Security
Pre-Encrypted
For your security the router is pre-encrypted with a unique password
Guest Network
Create a secure isolated network for guest internet access only
Parental Controls
Control access to specific websites

© Copyright 2012 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide TEW-733GR
5
Performance
N300 Wireless
Proven 300 Mbps Wireless N
Gigabit Ports
Gigabit ports extend high performance wired connections
Wireless Coverage
Extensive wireless coverage with MIMO antenna technology
Quality of Service (QoS)
Advanced QoS prioritizes video and audio transmissions
Compatibility
Compatible with older Wireless G devices
Energy Savings
Embedded GREENnet technology reduces power consumption by up to
50%
IPv6
IPv6 network support
*Maximum wireless signal rates are referenced from IEEE 802.11 theoretical specifications. Actual
data throughput and coverage will vary depending on interference, network traffic, building
materials and other conditions.
Product Hardware Features
Rear View
•Reset Button: Use an item such as a paperclip to push and hold this button for
10 seconds and release to reset your router to its factory defaults.
•WPS Button: Wi-Fi Protected Setup Button (WPS), press for 3 seconds to
activate feature.
•LAN Ports”Connect Ethernet cables (also called network cables) from your
router LAN ports to your wired network devices.
•WAN Port: Connect an Ethernet cable from your router WAN port to your
modem.
•Power Port:Connect the included power adapter from your router power port
and to an available power outlet.
•On/Off Power Switch:Push the router On/Off power switch to turn your router
“On” (Inner position) or “Off” (Outer position).
Reset Button
LAN Ports
WAN Port
Power Port
On/Off
Power switch
WPS button

© Copyright 2012 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide TEW-733GR
6
Front View
•WPS LED: This LED indicator blinks when WPS is active and searching for WPS
clients.
•Wireless (Link/Activity) LED: This LED indicator is blinking green when the
wireless is “On” and functioning properly on your router. This LED indicator will
be blinking green rapidly while data is transmitted or received by your wireless
clients or wireless network devices connected to your router.
•LAN 1-4 (Link/Activity) LEDs: These LED indicators are solid green when the
LAN ports are successfully connected to your wired network devices (which are
turned on). These LED indicators will blink green while data is transmitted or
received through your router’s LAN ports.
•Internet (Link/Activity) LED: This LED indicator is solid green when your router
WAN port is physically connected to the modem Network port (also called
network port) successfully with a Network cable. The LED indicator will be
blinking green while data is transmitted or received through the WAN port of
your router.
•Power LED: This LED indicator is solid green when your router is powered on.
Otherwise if this LED indicator is off, there is no power to your router.
Wireless LED
WPS button
LAN 1-4 LEDs
Internet LED
Power LED

© Copyright 2012 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide TEW-733GR
7
Application Diagram
The router is installed near the modem typically supplied by your ISP “Internet Service
Provider. The router’s WAN port is physically connected to the modem’s network port
which connects to the Internet. Wireless signals from the router are broadcasted to
wireless clients such as laptops (with wireless capability) thereby providing Internet
access throughout your network.
Basic Router Setup
Creating a Home Network
What is a network?
A network is a group of computers or devices that can communicate with each other. A
home network of more than one computer or device also typically includes Internet
access, which requires a router.
A typical home network may include multiple computers, a media player/server, a
printer, a modem, and a router. A large home network may also have a switch,
additional routers, access points, and many Internet-capable media devices such as TVs,
game consoles, and Internet cameras.
•Modem:Connects a computer or router to the Internet or ISP (Internet Service
Provider).
•Router:Connects multiple devices to the Internet.
•Switch: Connect several wired network devices to your home network. Your router
has a built-in network switch (the LAN port 1-4). If you have more wired network
devices than available Ethernet ports on your router, you will need an additional
switch to add more wired connections.
How to set up a home network
1. For a network that includes Internet access, you’ll need:
•Computers/devices with an Ethernet port (also called network port) or wireless
networking capabilities.
•A modem and Internet service to your home, provided by your ISP (modem typically
supplied by your ISP).
•A router to connect multiple devices to the Internet.
2. Make sure that your modem is working properly. Your modem is often provided by
your Internet Service Provider (ISP) when you sign up for Internet service. If your
modem is not working contact your ISP to verify functionality.
3. Set up your router. See “How to setup your router” below.
4. To connect additional wired computers or wired network devices to your network,
see “Connect additional wired devices to your network” on page 10.

© Copyright 2012 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide TEW-733GR
8
5. To set up wireless networking on your router, see “Secure your wireless network” on
page 12.
How to setup your router
Refer to the Quick Installation Guide or continue to the next section “Router
Installation” on page 8 for more detailed installation instructions.
Where to find more help
In addition to this User’s Guide, you can find help below:
•http://www.trendnet.com/support
(documents, downloads, and FAQs are available from this Web page)
Router Installation
Before you Install
Many Internet Service Providers (ISPs) allow your router to connect to the Internet
without verifying the information fields listed below. Skip this section for now and if
your router cannot connect to the Internet using the standard installation process, come
back to this page and contact your ISP to verify required ISP specification fields listed
below.
1. Obtain IP Address Automatically (DHCP)
Host Name (Optional)
Clone Mac Address (Optional)
2. Fixed IP address
WAN IP Address: _____. _____._____._____
(e.g. 215.24.24.129)
WAN Subnet Mask: _____. _____._____._____
WAN Gateway IP Address: _____. _____._____._____
DNS Server Address 1: _____. _____._____._____
DNS Server Address 2: _____. _____._____._____
3. PPPoE to obtain IP automatically
User Name: _________
Password: ________________
Verify Password: ________________
4. PPPoE with a fixed IP address
User Name: _________
Password: ________________
Verify Password: ________________
IP Address: ____. _____._____._____ (e.g. 215.24.24.129)

© Copyright 2012 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide TEW-733GR
9
Hardware Installation
1. Verify that you have an Internet connection when connecting your computer directly
to your modem.
2. Turn off your modem.
3. Disconnect the Network cable from your computer to your modem.
4. Use a Network cable and connect the WAN port (yellow port) on the router to your
modem.
5. Use another Network cable and connect your computer to one of the four LAN ports
on the router.
6. Plug in the power adapter, connect it to the router’s power port, and then push the
On/Off Power Switch to the “On” position (pushed in).
7. Turn on your modem.
8. Verify that the following front panel LED indicators on your router: Power (Solid
Green), Status (Blinking Green), LAN 1, 2, 3, or 4 (Solid/Blinking Green for ports for
which devices are connected), WAN (Solid/Blinking Green), and WLAN (Blinking
Green).
Setup Wizard
1. Open your web browser and the router’s configuration screen will automatically
appear. If not type, http://tew-733gr on the address bar of your web browser.
2. Select the language to use on the bottom drop-down list to select your preferred
language. Enter the default user name and password and then click Login to continue.
Default User Name: admin
Default Password: Please refer to the device label or wireless sticker on the unit for
more information.
Note: For added security your router has a unique login password and wireless
settings.
3. Once you are logged in to the router. You will begin the router’s setup wizard. Click
Next.

© Copyright 2012 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide TEW-733GR
10
4. The setup wizard will detect your internet connection. Continue to step 6 if your
internet connection type was detected.
5. If the wizard was unable to detect your internet connection type you will be asked to
select your internet connection type. Click Next to continue. Please contact your ISP
(Internet Service Provider) for additional information of your internet connection
type.
6. Verify your wireless settings and click Exit to complete the wizard.
Note: For added security your router comes with preconfigured wireless settings,
please refer to the device label or wireless sticker on the unit for more information.
Connect additional wired devices to your network
You can connect additional computers or other network enabled devices to your
network by using Ethernet cables to connect them to one of the available LAN ports
labeled 1,2,3,4 on your router. Check the status of the LED indicators (1, 2, 3, or 4) on
the front panel of your router to ensure the physical cable connection from your
computer or device.
Note: If you encounter issues connecting to your network, there may be a problem
with your computer or device network settings. Please ensure that your computer or
device network settings (also called TCP/IP settings) are configured to obtain IP
address settings automatically (also called dynamic IP address or DHCP) and to
Obtain DNS Server address settings automatically.

© Copyright 2012 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide TEW-733GR
11
Wireless Networking and Security
How to choose the type of security for your wireless network
Setting up wireless security is very important. Leaving your wireless network open and
unsecure could expose your entire network and personal files to outsiders. TRENDnet
recommends reading through this entire section and setting up wireless security on your
new router.
There are a few different wireless security types supported in wireless networking each
having its own characteristics which may be more suitable for your wireless network
taking into consideration compatibility, performance, as well as the security strength
along with using older wireless networking hardware (also called legacy hardware).
It is strongly recommended to enable wireless security to prevent unwanted users from
accessing your network and network resources (personal documents, media, etc.).
In general, it is recommended that you choose the security type with the highest
strength and performance supported by the wireless computers and devices in your
network. Please review the security types to determine which one you should use for
your network.
Wireless Encryption Types
•WEP: Legacy encryption method supported by older 802.11b/g hardware. This is
the oldest and least secure type of wireless encryption. It is generally not
recommended to use this encryption standard, however if you have old 802.11 b or
802.11g wireless adapters or computers with old embedded wireless cards(wireless
clients), you may have to set your router to WEP to allow the old adapters to
connect to the router.
Note: This encryption standard will limit connection speeds to 54Mbps.
•WPA: This encryption is significantly more robust than the WEP technology. Much
of the older 802.11g hardware was been upgraded (with firmware/driver upgrades)
to support this encryption standard. Total wireless speeds under this encryption
type however are limited to 54Mbps.
•WPA-Auto: This setting provides the router with the ability to detect wireless
devices using either WPA or WPA2 encryption. Your wireless network will
automatically change the encryption setting based on the first wireless device
connected. For example, if the first wireless client that connects to your wireless
network uses WPA encryption your wireless network will use WPA encryption. Only
when all wireless clients disconnect to the network and a wireless client with WPA2
encryption connects your wireless network will then change to WPA2 encryption.
NOTE: WPA2 encryption supports 802.11n speeds and WPA encryption will limit
your connection speeds to 54Mbps
•WPA2: This is the most secure wireless encryption available today, similar to WPA
encryption but more robust. This encryption standard also supports the highest
connection speeds. TRENDnet recommends setting your router to this encryption
standard. If you find that one of your wireless network devices does not support
WPA2 encryption, then set your router to either WPA or WPA-Auto encryption.
Note: Check the specifications of your wireless network adapters and wireless
appliances to verify the highest level of encryption supported.
Below is brief comparison chart of the wireless security types and the
recommended configuration depending on which type you choose for your wireless
network.
Security Standard WEP WPA WPA2
Compatible
Wireless
Standards
IEEE 802.11a/b/g
(802.11n devices
will operate at
802.11g to connect
using this standard)
IEEE 802.11a/b/g
(802.11n devices
will operate at
802.11g to connect
using this
standard) IEEE 802.11a/b/g/n
Highest
Performance
Under This
Setting Up to 54Mbps Up to 54Mbps Up to 450Mbps*
Encryption
Strength Low Medium High
Additional
Options
Open System or
Shared Key,
HEX or ASCII,
Different key sizes
TKIP or AES,
Preshared Key or
RADIUS
TKIP or AES,
Preshared Key or
RADIUS
Recommended
Configuration
Open System ASCII
13 characters
TKIP
Preshared Key
8-63 characters
AES
Preshared Key
8-63 characters
*Dependent on the maximum 802.11n data rate supported by the device (150Mbps,
300Mbps, or 450Mbps)

© Copyright 2012 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide TEW-733GR
12
Secure your wireless network
Wireless > Security
After you have determined which security type to use for your wireless network (see
“How to choose the security type for your wireless network” on page 11), you can set up
wireless security.
1. Log into your router management page (see “Access your router management page”
on page 22).
2. Click on Wireless, and click on Security.
3. Click on the Authentication Type drop-down list to select your wireless security type.
Selecting WEP:
If selecting WEP (Wired Equivalent Privacy), please review the WEP settings to configure
and click Apply to save the changes.
•WEP:Choose Open System or Shared Key.
Note: It is recommended to use Open System because it is known to be more
secure than Shared Key.
•Mode:Choose HEX or ASCII.
Note: It is recommended to use ASCII because of the much larger character set
that can be used to create the key.
•WEP Key:Choose the key length 64-bit or 128-bit.
Note: It is recommended to use 128-bit because it is more secure to use a key that
consists of more characters.
WEP Key Format HEX ASCII
Character set 0-9 & A-F, a-f only Alphanumeric (a,b,C,?,*, /,1,2, etc.)
64-bit key length 10 characters 5 characters
128-bit key length 26 characters 13 characters

© Copyright 2012 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide TEW-733GR
13
•Key 1-4
oThis is where you enter the password or key needed for a computer to
connect to the router wirelessly
oYou can define up to 4 passwords or 4 keys. Only one key can be active at a
given time. Most users simply define one key.
oChoose a key index 1, 2, 3, or 4 and enter the key.
oWhen connecting to the router, the client must match both the password
and the Key number. (e.g. if you have activated Key 2 with a password of
12345, then the client must select: Key 2 (entering Key 1, 3, or 4 will block
the ability to connect) and enter password 12345)
Selecting WPA, WPA-Auto, or WPA2 (WPA2 recommended):
First, from the Authentication Type row, select WPA, WPA-Auto, or WPA2.
Then from the PSK/EAP row, select either PSK or EAP
•PSK stands for Preshared Key
•EAP stands for Extensive Authentication Protocol, also called Remote
Authentication Dial-In User Service or RADIUS).
Note: EAP requires an external RADIUS server, PSK only requires you to create a
passphrase.
The following section outlines options when selecting PSK (Preshared Key Protocol),
oSelect a Cipher Type. When selecting WPA security, it is recommended to use
TKIP.
oWhen selecting WPA-Auto security, it is recommended to use AES.
oWhen selecting WPA2 security, it is recommended to use AES.
Create your Wireless security Passphrase (password or key):
•Passphrase – Enter the passphrase.
•This is the password or key that is used to connect your computer to this router
wirelessly
•Confirmed Passphrase – Re-enter the passphrase.
Note: 8-63 alphanumeric characters (a,b,C,?,*, /,1,2, etc.)
The following section outlines options when selecting EAP (Extensive Authentication
Protocol),
EAP (Extensible Authentication Protocol) is also called Remote Authentication Dial-In
User Service or RADIUS.
Select a Cipher Type
oWhen selecting WPA security, it is recommended to use TKIP.
oWhen selecting WPA-Auto security, it is recommended to use AES.
oWhen selecting WPA2 security, it is recommended to use AES.

© Copyright 2012 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide TEW-733GR
14
•RADIUS Server 1/2 - Configure the RADIUS server settings.
Note: RADIUS Server 2 is optional and can be configured as a backup if there are
any issues with RADIUS Server 1.
oIP – Enter the IP address of the RADIUS server. (e.g. 192.168.10.250)
oPort – Enter the port your RADIUS server is configured to use for RADIUS
authentication.
Note: It is recommended to use port 1812.
oShared Secret – Enter the shared secret used to authorize your router with
your RADIUS server.
Connect wireless devices to your router
A variety of wireless network devices can connect to your wireless network such as:
•Gaming Consoles
•Internet enabled TVs
•Network media players
•Smart Phones
•Wireless Laptop computers
•Wireless IP cameras
Each device may have its own software utility for searching and connecting to available
wireless networks, therefore, you must refer to the User’s Manual/Guide of your
wireless client device to determine how to search and connect to this router’s wireless
network.
See the “Appendix” on page 51 for general information on connecting to a wireless
network.

© Copyright 2012 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide TEW-733GR
15
Connect wireless devices using WPS
WPS (Wi-Fi Protected Setup) is a feature that makes it easy to connect devices to your
wireless network. If your wireless devices support WPS, you can use this feature to
easily add wireless devices to your network.
Note: You will not be able to use WPS if you set the SSID Broadcast setting to Disabled.
There are two methods the WPS feature can easily connect your wireless devices to
your network.
•Push Button Configuration (PBC) method
oRECOMMENDED Hardware Push Button method–with an external button
located physically on your router and on your client device
oWPS Software/Virtual Push Button - located in router management page
•PIN (Personal Identification Number) Method - located in router management
page
Note: Refer to your wireless device documentation for details on the operation of
WPS.
Recommended Hardware Push Button (PBC) Method
To add a wireless device to your network, simply push the WPS button on the wireless
device you are connecting(consult client device User’s Guide for length of time), then
push and hold the WPS button located on your router for 3 seconds and release it. A
Green LED on your router WPS button will flash indicating that the WPS setup process
has been activated on your router. (See “Product Hardware Features” on page 5)
For connecting additional WPS supported devices, repeat this process for each
additional device.
Note it is recommended that a wireless key (passphrase or password) is created
before connecting clients using the PBC method. If no wireless key is defined when
connecting via PBC, the router will automatically create an encryption key that is 64
characters long. This 64 character key will then have to be used if one has to
connect computers to the router using the traditional connection method.
PBC (Software/Virtual Push Button)
Wireless >WiFi Protected Setup
In addition to the hardware push button located physically on your router, the router
management page also has push button which is a software or virtual push button you
can click to activate WPS on your router.
1. Log into your router management page (see “Access your router management page”
on page 22).
2. Click on Wireless, and click on WPS.
3. To add a wireless device to your network, simply click Connect under Add Wireless
Station to begin WPS.
4. You will receive an option of Auto and Manual. Select Auto and click Next to continue
with WPS.
5. Select PBC option to continue using WPS PBC method and click Next .

© Copyright 2012 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide TEW-733GR
16
Note: You may need to initiate the WPS PIN on your wireless device first when using
this method. Refer to your wireless device documentation for details on the
operation of WPS.
5. You will receive a success message indicate that the wireless device successfully
connected using WPS.
PIN (Personal Identification Number)
Wireless >WiFi Protected Setup
If your wireless device has WPS PIN (typically an 8-digit code printed on the wireless
device product label or located in the wireless device wireless software utility), you can
use this method.
1. Log into your router management page (see “Access your router management page”
on page 22).
2. Click on Wireless, and click on WPS.
3. To add a wireless device to your network, simply click Connect under Add Wireless
Station to begin WPS.
4. You will receive an option of Auto and Manual. Select Auto and click Next to continue
with WPS.
5. Select PIN option and enter your wireless device’s PIN information. Click Next to
continue.
Basic wireless settings
Wireless > Basic
This section outlines available management options under the Basic Wireless sub tab.
1. Log into your router management page (see “Access your router management page”
on page 22).
2. Click on Wireless, and click on Basic.
3. To save changes to this section, click Save Settings when finished.

© Copyright 2012 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide TEW-733GR
17
•Wireless
oEnable: Check the box to enable wireless networking on your router.
oDisable: Uncheck the box to disable wireless networking
oSchedule: Select an applied schedule rule on the drop down list of when the
wireless network will be enabled. Select Always to have wireless network
always enabled.
oNew Schedule: Click this button to set a new schedule rule.
•Wireless Network Name (SSID): The acronym SSID stands for Service Set
Identifier and is the name of your wireless network. It differentiates your wireless
network from others around you. By default, the router has a predefined SSID
(refer to the wireless sticker or device label). If you choose to change the SSID,
change it to a name that you can easily remember.
•802.11 Mode:Select the appropriate mode for your network.
o2.4GHz 802.11b/g/n mixed mode:Select this mode for the best
compatibility. This mode allows older 802.11b and 802.11g wireless devices
to connect to the router in addition to newer 802.11n devices.
o2.4GHz 802.11b/g mixed mode:This mode only allows devices to connect to
the router using older and slow 802.11b or 802.11g technology and it
thereby reduces the router’s maximum speed to 54Mbps (typically not
recommended).
o2.4GHz 802.11n only mode:This mode only allows newer 802.11n devices to
connect to your router. This mode does ensure the highest speed and
security for your network, however if you have older 802.11g wireless clients,
they will no longer be able to connect to this router.
o2.4GHz 802.11g only mode:This mode only allows devices to connect to the
router using older and slow 802.11g technology (typically not
recommended).
o2.4GHz 802.11b only mode:This mode only allows devices to connect to the
router using older and slow 802.11b technology (typically not
recommended).
Note: Please check the specifications on your wireless devices for the highest
wireless capability supported first before applying these settings. If you are
unsure, it is recommended that you keep the default setting (2.4GHz
802.11b/g/n mixed mode) for the best compatibility.
When applying the 802.11 mode setting, please keep in mind the following:
•Wireless devices that support 802.11n are backwards compatible and can
connect wirelessly at 802.11g or 802.11b.
•Connecting at 802.11b or 802.11g will limit the capability of your 802.11n
supported wireless devices from obtaining higher performance and data rates.
•Allowing 802.11b or 802.11g devices to connect to an 802.11n capable wireless
network may degrade the wireless network performance below the higher
performance and data rates of 802.11n.
•Wireless devices that only support 802.11b or 802.11g will not be able to connect
to a wireless network that is set to 802.11n only mode.
•Wireless devices that only support 802.11b will not be able to connect to a
wireless network that is set to 802.11g only mode.
•Auto Channel:In North America, this router can broadcast on 1 of 11 Channels
(13 in Europe and other countries). Selecting Auto Channel enables the router to
automatically select the best Channel for wireless communication.
•Channel: To manually set the channel on which the router will broadcast,
uncheck Auto Channel, then click the drop-down list and select the desired
Channel for wireless communication. The goal is to select the Channel that is
least used by neighboring wireless networks.
•Transmission Rate: Set the transmission rate of your wireless network. Please
note that it is best that this setting remains on the default setting of Best.

© Copyright 2012 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide TEW-733GR
18
•802.11 Mode:Select the appropriate mode for your network.
•Channel Width:This setting only applies to wireless devices connecting at
802.11n. Select the appropriate channel width for your wireless network.
o20 MHz:This mode operates using a single 20MHz channel for wireless
devices connecting at 802.11n. This setting may provide more stability than
Auto 20/40 MHz for connectivity in busy wireless environments where there
are several wireless networks in the area.
oAuto 20/40 MHz:This mode can automatically switch between using a single
20MHz channel or 40MHz (two 20MHz channels). When 40MHz is active, this
mode is capable of providing higher performance only if the wireless devices
support the 40MHz channel width. Enabling 20/40MHz typically results in
substantial performance increases when connecting to an 802.11n client.
•Visibility Status
oVisible: Allows wireless devices to search and discover your wireless network
name (also called SSID) broadcasted by your router.
oInvisible: Turns off the ability for wireless devices to find your network. It is
still possible for wireless devices to be configured to connect to your wireless
network.
Note: Setting this option to Invisible, may cause issues with your wireless
adapters.
•WMM:Wi-Fi Multimedia is a Quality of Service (QoS) feature which prioritizes
audio and video data packets. This feature requires the wireless device to also
support WMM. Click Enabled (recommended) or Disabled to turn this feature on
or off on your router.
Guest Zone
Access > Guest Zone
Creating an isolated and separate wireless guest network allows wireless clients to
connect to your network for Internet access only and keep your local LAN network safe
by restricting guest access to your LAN network resources such as shared documents
and media files on your computers, network storage, and printers.
1. Log into your router management page (see “Access your router management page”
on page 22).
2. Click on Access and click on Guest Zone.
3. Review the Guest Zone settings, click Save Settings to continue.
•Enabled: Check the option to enable the Guest Network. Select Always to have
guest zone enabled always or select a schedule rule in the pull down menu.
•Wireless Network Name (SSID): This acronym stands for Service Set Identifier and
is the name of your wireless network. It differentiates your wireless network from
others around you. It is recommended to use a different name from your primary
wireless network to a name that you can easily identify and differentiate from the
primary. You can reference your guests to access this network instead of the
primary.
•Enable Routing Between Zone: Select this option to allow guests to restrict your
guest to only have access to the Internet.
•Security Mode: Select the wireless security you would like to apply to the guest
zone.

© Copyright 2012 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide TEW-733GR
19
Steps to improve wireless connectivity
There are a number of factors that can impact the range of wireless devices. Follow
these tips to help improve your wireless connectivity:
1. Keep the number of obstructions to a minimum. Each obstruction can reduce the
range of a wireless device. Position the wireless devices in a manner that will
minimize the amount of obstructions between them.
a. For the widest coverage area, install your router near the center of your
home, and near the ceiling, if possible.
b. Avoid placing the router on or near metal objects (such as file cabinets and
metal furniture), reflective surfaces (such as glass or mirrors), and masonry
walls.
c. Any obstruction can weaken the wireless signal (even non-metallic objects),
so the fewer obstructions between the router and the wireless device, the
better.
d. Place the router in a location away from other electronics, motors, and
fluorescent lighting.
e. Many environmental variables can affect the router’s performance, so if your
wireless signal is weak, place the router in several locations and test the
signal strength to determine the ideal position.
2. Building materials can have a large impact on your wireless signal. In an indoor
environment, try to position the wireless devices so that the signal passes
through less dense material such as dry wall. Dense materials like metal, solid
wood, glass or even furniture may block or degrade the signal.
3. Antenna orientation can also have a large impact on your wireless signal. Use
the wireless adapter’s site survey tool to determine the best antenna
orientation for your wireless devices.
4. Interference from devices that produce RF (radio frequency) noise can also
impact your signal. Position your wireless devices away from anything that
generates RF noise, such as microwaves, radios and baby monitors.
If possible, upgrade wireless network interfaces (such as wireless cards in computers)
from older wireless standards to 802.11n. If a wirelessly networked device uses an older
standard, the performance of the entire wireless network may be slower. If you are still
experiencing low or no signal consider repositioning the wireless devices or installing
additional access points.
Advanced wireless settings
Wireless > Advanced
These settings are advanced options that can be configured to change advanced
wireless broadcast specifications. It is recommended that these settings remain set to
their default values unless you are knowledgeable about the effects of changing these
values. Changing these settings incorrectly can degrade performance.
•Transmit Power:The transmit power of your wireless radio can be adjusted in
percentages.
Default Value:100%
•Beacon Period: A beacon is a management frame used in wireless networks that
transmitted periodically to announce the presence and provide information
about the router’s wireless network. The interval is the amount time between
each beacon transmission.
Default Value:100 milliseconds (range: 20-1000)
•Preamble Type: Select Short or Long Preamble

© Copyright 2012 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide TEW-733GR
20
Access Control Filters
Access control basics
MAC address filters
Access > Filter > MAC Filters
Every network device has a unique, 12-digit MAC (Media Access Control) address. Using
MAC filters, you can allow or deny specific computers and other devices from using this
router’s wired or wireless network.
1. Log into your router management page (see “Access your router management page”
on page 22).
2. Click on Access, click on Filter, and click on MAC Filters. Click Save Settings to apply
rule.
3. Review the MAC Filter options.
•Turn Off: Disables MAC address filter.
•Mac Filter ON and Allow computers/devices with MAC addresses listed below to
access the local network (LAN/WLAN), web management, and the Internet.
•Mac Filter ON and Deny computers/devices with MAC addresses listed below to
access the local network (LAN/WLAN), web management, and the Internet
Note: MAC filter can be configured to allow access to the listed MAC address and
deny all others unlisted or vice versa. The recommended function is to choose to
only allow access to the MAC addresses listed and deny all others unlisted because it
is easier to determine the MAC addresses of devices in your network then to
determine which MAC addresses you do not want to allow access.
Add the MAC addresses to the MAC Table first before applying the MAC filter function.
Note: Do not configure this setting until you have added the MAC addresses to the
MAC Table first. The recommended option is to only Allow access to the MAC
addresses listed and deny all others unlisted.
•Check box: Check the box to enable rule.
•MAC Address – Enter the 12-digit MAC address.(e.g. 00-11-22-AA-BB-CC)
•Schedule: Select Always to have rule always on or select a schedule rule.
Note: You can check the Dynamic DHCP List for the MAC addresses of the devices on
your network, see “Setup the DHCP server on your router” on page 28 or refer to your
computer or device documentation to find the MAC address.
Parental Controls/URL Filters
Access > Filter > Domain/URL Blocking
You may want to allow or block computers or devices on your network access to specific
websites (e.g. www.trendnet.com, etc.), also called domains or URLs (Uniform Resource
Locators). You may also enter a keyword (e.g. instead of complete URL to generally
allow or block computers or devices access to websites that may contain the keyword in
the URL or on the web page.
1. Log into your router management page (see “Access your router management page”
on page 22).