TRENDnet TW100-S4W1CA User manual

Copyright ©2005. TRENDware International, Inc.All Rights Reserved.
TRENDnet
TRENDware, USA
What's Next in Networking
Version 06.18.05
TW100-S4W1CA
DSL/Cable Broadband Router with 4-Port Switch
Quick Installation Guide
DSL/Cablu Broadband Router cu 4-Port Switch
Ghid rapid de instalare

Table of Contents
English ...........................................................................................
Româna .........................................................................................
Troubleshooting................................................................................
1
1
18
18
20
21
28
36
1. Prepare for Installation ............................................................
2. Install Hardware ......................................................................
3. Configure the computer’s TCP/IP Settings .............................
4. Configure the Router ..............................................................
1.
2. Instalarea Hardware ...............................................................
3. Setarea TCP/IP ......................................................................
4. Configurarea Routerului .........................................................
Pregatiti-va pentru instalare ....................................................
3
4
10

1. Prepare for Installation
Thank you for purchasing the TW100-S4W1CA. This router will allow you to
share your Internet connection with multiple users while its firewall protects
your network from hackers.
This guide will help you set up and configure your router. Following the
installation instructions should be quick and easy. If you run into problems,
please refer to the Troubleshooting section or the more detailed installation
procedures on the User's Guide. If you need further technical support, please
visit www.trendnet.com or call by phone.
Verify Equipment
Before installing the router you should have:
1. A Cable/DSL Modem with an Ethernet Port Set-up
2. A working Internet account
3. A Web Browser such as Internet Explorer (5.0 or higher) or Netscape
Navigator (4.7 or higher)
4. An RJ-45 Network Cable for each computer connected to the router.
5. TCP/IP protocol installed on computer(s)
6. Computers with "Client for Microsoft Networks" installed
Verify Package Contents
Please make sure you have everything in the box:
1
TW100-S4W1CA
Quick Installation Guide User Guide
AC Power Adapter RJ-45 Network Cable
English
English QIG
Copyright ©2004. TRENDware International, Inc.All Rights Reserved.
TRENDnet
TRENDware, USA
What's Next in Networking
TW100-S4W1CA
User's Guide
Cable/DSL
4-Port Broadband Router
Copyright ©2005. TRENDware International, Inc.All Rights Reserved.
TRENDnet
TRENDware, USA
What's Next in Networking
Version 06.18.05
TW100-S4W1CA
DSL/Cable Broadband Router with 4-Port Switch
Quick Installation Guide
DSL/Cablu Broadband Router cu 4-Port Switch
Ghid rapid de instalare

2
Collect Internet Service Provider (ISP) Information
During the installation of your router the Set-Up Wizard will ask you for specific
Internet Service Provider ISP information you should have been provided from
your ISP to set up your Cable or DSL connection. The information is different
based on your type of Internet Connection. Please verify your Internet
Connection type and ensure you have the following information:
Dynamic IP Cable Connection
Nothing required. IP address will automatically be assigned by the ISP.
Static or Fixed IP Cable Connection
Internet IP Address:____.____.____.____
Subnet Mask: ____. ____. ____. _____
Gateway IP Address:____.____.____._____
Primary DNS:____.____._____.______
Secondary DNS:_____._____._____.____
PPPoE DSL Connection
Login Name:______________
Password:________________
PPTP DSL Connection
Login Name:_______________
Password:_________________
(eg. 215.24.24.129)
English

3
2. Install Hardware
3
25
TW100-S4W1CA
POWER
1. Turn off your Cable/DSL Modem, Router, and PC.
2. Connect one RJ-45 network cable from the Modem's Ethernet port to the
Router's WAN port.
3. Connect a different RJ-45 network cable from one of the Router's LAN ports
to your computer's network port.
4. Turn on your Cable/DSL modem.
5. Turn on your router.
6. Turn on your computer.
POWER
WAN
LAN
Verify Hardware Installation
Verify that the following router front panel lights are on: Power, WAN, and one
LAN port. (for each computer connected to your router)
English

4
3. Configure the computer's TCP/IP Settings
Windows 95/98/98SE/ME
This next section will ensure that your computer can communicate with your
router. To do this, you will need to configure the TCP/IP settings in your
Operating System (OS). Configuration instructions for Windows OS-based
computers are shown below. For computers running other operating systems,
see your system documentation for configuration instructions.
1. Find Start Button located on Desktop.
2. Click Start;Click Settings and then click on Control Panel.
3. Double-Click the Network Icon and the Network Properties box will appear.
4. Under the General Configuration Tab, locate and select TCP/IP with the
corresponding network card (such as TRENDnet TE100-PCIWN
10/100Mbps Network Adapter), and then click on the Properties button and
the TCP/IP window will appear.
NOTE: If you have a Static IP address connection, write down the IP
addresses from the following sections before you change the settings.
English

5
6. Now go to the Gateway tab and make sure no Gateways are listed in the
Installed Gateway's section. If there is Gateway installed, click Remove to
remove it.
5. Under the IP Address Tab, select Obtain an IP address automatically.
English

6
7. Go to the DNS Configuration tab and click Disable DNS. Then click OK.
8. Click OK on the TCP/IP Properties box.
9. Click OK on the Network Box.
10. At this point, the installation may require files from your Windows CD-ROM.
If this happens, insert Windows 98 CD-ROM into your CD-ROM drive and
select CD-ROM drive to load the files.
11. After the files load, the System Settings Change message appears, click
Yes to reboot your system. Your computer will now load your new TCP/IP
settings.
NOTE: If the message does not appear, you will need to manually
restart your computer.
English

7
13. The IP configuration box will appear. Choose your Network adapter from
the dropdown box (such as TRENDnet TE100-PCIWN 10/100Mbps network
adapter)and the current IP address information of your computer will show
in the box, including the following: IP Address, Subnet Mask and Default
Gateway.
14. If your IP Address shows the following information, your computer is now
successfully connected to the router:
IP Address: 192.168.1.x
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.1.1
NOTE: If the information shown is incorrect, please reboot and retry the
steps above.
12. After your system reboots, click Start; click on Run. Then type winipcfg in
the field and click OK.
English

8
1. Click Start; click Settings, and click on Control Panel.
2. Double-click the Network Connections Icon.
3. Right-click on the Local Area Connection Icon, and then click on
Properties. The Local Area Connection Properties box will appear.
4. Under the "General Configuration" Tab, locate and select TCP/IP and then
click Properties. The Internet Protocol (TCP/IP) Properties box will appear.
NOTE: If you have a Static IP address connection, write down the IP
addresses from the following sections before you remove them from the
settings.
Windows 2000/XP
5. Click on Obtain an IP address automatically and Obtain DNS Server
address automatically.
English