Triax MOD 102T User manual

Modulator MOD 102T
User Manual
Article Article no.
MOD 102T Modulator 300127
Version A Date 02/2018 EN

Introduction
The MOD102T modulator has an HDMI input with local loop through, and a COFDM
output which is combined with the F input. The HDMI input content can be supplied by
a number of sources, Blu-ray player, Satellite Set top box, CCTV etc. The input signal is
modulated as a COFDM output and can be distributed to a number of TV’s over an
existing private coaxial network.
It has an HDMI loop through, to connect to the local TV, and can also combine existing
F with the modulated output channel on F Out 1 and F Out 2. The modulator has
adjustable level control to balance the COFDM channel with the incoming F channels.
The source Set top box can be controlled from another TV location, via the I remote
control over the coaxial cable, using an I transmitter and a digital link. The coaxial
network must be connected to the F Out 2, with the 9vdc able to pass through the
network, to remotely power the digital link.
The MOD102T Modulator can be set up, either via the front panel and LCD screen, or
through the Web user interface ( J45 connector). Please see below for full instructions.

Equipment Detail
 MOD102T Basic Installation:
1. Connect HDMI In (4) and eceiver (STB)
2. Connect HDMI Output (3) and local TV
3. Connect F Out 1 (B) and local TV
4. Connect F In (1) with Terrestrial input (Aerial)
5. Plug power adapter into DC9V/2A (8)
 Connect MOD102T with I Transmitter and Triax Digital Link:
1. Connect the I Transmitter to I sensor (2) at the rear of the Modulator and ensure it points to
the receiver (STB)
2. Connect Triax Digital Link (not included in accessories) at the other TV location, ensure the coax
network is connected to F Out 2 DC9V (C).
 For WebUI adjustment and Upgrade
1. Connect Ethernet (6) and PC/Laptop via J45 to adjust setting and apply software upgrades.
Interface:
1. F In
2. I Sensor
3. HDMI Out
4. HDMI In
5. USB
6. Ethernet
7. On/Off
8. DC 9V/2A
A. Buttons: ▲▼◄ ► Menu, OK
B. F Out 1
C. F Out 2 DC 9V

SET UP
Instruction o
n
how to
set up the modulator using the front panel LCD display
Press OK and to make any adjustments or changes, confirm changes by pressing OK again.

Instruction of how to use
WebUI
1.
Connecting to modulator
Step 1: Set the PC’s static IP address to 169.254.0.100
Step 2: Connect MOD102T to computer via an Ethernet cable.
Step 3: Open your browser and enter 169.254.0.3
(The Web UI only supports Windows 7 browsers or above.)
2.
Login Page:
Enter user name and password, and click login button.
Username: user
Password: 12345
<<After login, you can see main page as below

3.
Modulator Setting:
F Status:
1. F On/Off: Users can either turn the F on or off in this this menu.
Encoder Setting:
1. Audio Type: Users can choose either AAC or MPEG.
Service Setting:
1. Service Name: Users can edit the service name (TV Program Name).
2. Service ID: Users are able to define a device ID from 1 to 65534.
Channel Setting:
1. Channel: Users can select the F output channel number from the pre-set UK channel plan.
2. LCN: Users can define the Logical Channel Number from 1 to 1023.

Stream Setting:
1. OrgNetwork ID: Users Users can edit OrgNetwork ID from 1 to 65534.
2. Network ID: Users can edit Network ID from 1 to 65534.
3. TS ID: Users can edit TS ID from 1 to 65534.
4. Network Name: Users can define the Network name.
Parameter Setting:
1. Constellation: The MOD102T contains the following constellation modes: QPSK, 16QAM and
64QAM.
2. Code ate: efers to the FEC (Forward Error Correction) rate. Which can be set as 5/6, or 7/8
3. Guard Interval: Users can select either 1/8, 1/16, 1/32.
4. Transmission Mode: Transmission mode can be set as either 2K and 8K FFT

4.
Utility:
Tftp Upgrade:
Select and upload bin file & apply firmware upgrade (details below).
Change Password Setting:
Old Password: Enter old password.
New Password: Enter pew password.
Confirm Password: Enter new password again.
System Information:
This shows the Device Version and Module Version.
Other Settings:
The user can also change the language setting to English, French, German, or Danish.

Tftp Upgrade instruction
5.
Tftp Upgrade instruction
I.
Set the PC’s static IP address to 169.254.0.100
II.
Launch Tftp tool and enter the below information under DHCP server tab.
III.
Open the internet browser and enter: 169.254.0.3
Username: user
Password: 12345
User can assign any
location, but the update file
must be in the assigned
folder.

IV.
Select Utility tab and click Tftp Upgrade button
V.
The web page and Tftp will begin the upgrade process.

6. Modulator default settings and options
Modulator Setting Description Default value Option
F Settings F On/off On On/Off
Output power 65 85,78,72,65
Encoder Settings Audio Type AAC AAC/MPEG
Service Settings Service name CH 62 Edit Service Name
Service ID
(1~65534)
256 Enter value : 1~65534
Channel Settings Channel CH36 CH 21 ~ 69
LCN (1~1023) 900 Enter value : 1~1023
Stream Settings Orgnetwork ID
(1~65534)
9018 Enter value : 1~65534
Network ID
(1~65534)
8350 Enter value : 1~65534
TS ID (1~65534) 8350 Enter value : 1~65534
Network Name T IAX Edit Network Name
Parameter Settings Constellation 64QAM QPSK/16QAM/64QAM
Code ate 5/6 5/6, 7/8
Guard Interval 1/8 1/8,1/16,1/32
Transmission
Mode
8K 2K, 8K
Bandwidth 8 7/8

Default Settings
Country Factory Setting UK France Denmark Germany Italy
F Output F Enable
On On On On On
F Power (dBuV) 65 65 65 65 65
Encoder Audio type
AAC AAC AAC AAC AAC
Service
Service Name
CH62 CH21 CH62 CH62 CH62
Service ID 256 256 256 256 256
Channels
Set CH
CH36 CH21 CH62 CH62 CH62
Set LCN 900 39 62 No loop No loop
Private Data Specifier
Descriptor
0x0000233A
0x0000002
8
0x0000002
9
No loop No loop
Stream
ON ID 9018 8442 8400 8468 8572
N ID 8350 8442 12801 12289 12289
TS ID 8350 301 8350 8350 8350
Network Name
T IAX T IAX T IAX T IAX T IAX
NIT Version
1 30 1 1 1
Parameter
Constellation
64QAM 64QAM 64QAM 64QAM
64QAM
Trans. Mode
8K 8K 8K 8K 8K
Guard Interval
1/8 1/8 1/8 1/8 1/8
Code ate
5/6 5/6 5/6 5/6 5/6
System
Info
Default
Password Old, New, Confirm 12345 12345 12345 12345 12345
Other Language
English French Danish German
Copyright © 2018 T IAX. All rights reserved.
The T IAX Logo and T IAX, T IAX Multimedia are registered trademarks or
trademarks
of the T IAX Company or its affiliates.
All specifications in this guide are subject to change without further notice.