Triax C-HD207CG User manual

Model Item no.
Triax C-HD207CG 305207/305208
Version 01- 2011 EN triax.com
Triax C-HD207CG
Digital Cable-TV Receiver

Content
2
Content
Content ...........................................................................................................................................2
General instructions .......................................................................................................................3
Safety Instructions .........................................................................................................................4
Cleaning and care ..........................................................................................................................4
Control elements, front and rear panel..........................................................................................5
Connecting the receiver.................................................................................................................6
Remote control ...............................................................................................................................7
Initial installation.............................................................................................................................8
Operating the receiver .................................................................................................................10
EPG –Electronic Programme Guide ..........................................................................................12
Settings.........................................................................................................................................12
Settings –Receiver setup ......................................................................................................13
Settings –Picture ...................................................................................................................14
Settings –Sound ....................................................................................................................15
Settings –Subtitle ..................................................................................................................15
Settings –OSD Configuration (Option) .................................................................................15
Settings –Parental lock .........................................................................................................17
Parental lock –device lock ....................................................................................................17
Parental Lock –changing the PIN .........................................................................................17
Installation ....................................................................................................................................18
Installation –channel search .................................................................................................18
Manual channel search ..........................................................................................................19
Installation –Factory reset .....................................................................................................19
Installation –Smartcard Reader ............................................................................................20
Channel list...................................................................................................................................21
Channel list –Edit main list ....................................................................................................21
Channel list –Edit favourites list ............................................................................................21
Channel list –Delete Antenna ...............................................................................................21
Timer ............................................................................................................................................22
Timer –record timer ...............................................................................................................22
Information ...................................................................................................................................23
Teletext.........................................................................................................................................23
Connection of external mass storage device ..............................................................................24
List of recordings..........................................................................................................................25
Operating the external mass storage device ..............................................................................26

3
Recording ...............................................................................................................................26
Timeshift function ...................................................................................................................26
Playback .......................................................................................................................................27
Choosing the audio channel for recordings ...........................................................................27
Fast forward and rewind.........................................................................................................27
Operating the hard disk –setting and managing markers ....................................................28
Using serial interface ...................................................................................................................29
Make a contribution to environmental protection ........................................................................29
Trouble-shooting ..........................................................................................................................30
Technical data ..............................................................................................................................31
General instructions
Warranty
The period of warranty starts when buying the device. Please verify the exact date by sales
check, delivery note, invoice, etc. Keep the documents carefully. Our warranty service refers
to our warranty terms valid at the time of buying the apparatus.
In case you require technical service please take or send the device to your specialised
dealer.
The unit is labelled with the CE-sign and therefore conforms with the general
requirements of the European guidelines. A Declaration of Conformity is in
the later section of this manual.
Dumping hint for packaging
Any packaging material is recyclable and should principally be supplied to the recycling
process.
Packaging and wrapping materials as plastic foils, etc. should never be available for children.

Safety Instructions
4
Safety Instructions
Before installing your digital receiver, all security and operating instructions should be read
carefully. The User’s Manual should be retained for future reference.
All operating and using instructions should be followed.
Never allow children to operate this electrical device without supervisor.
ENVIRONMENTAL CONDITIONS
Protect the receiver against humidity, heat and cold. Allow 10cm space around the receiver for
sufficient ventilation. Do not cover the receiver’s ventilation openings with items like
newspapers, tablecloths, curtains, etc. .
Do not place any objects filled with liquids, such as vases, on the digital receiver.
Take care that no foreign bodies or liquids are getting into the device.
Do not expose the digital receiver to dripping or splashing liquids.
CONNECTING TO MAINS SUPPLY (SAFETY FEATURE!)
Only connect the original mains adapter to a well reachable mains supply socket 230V~ 50Hz
only. Do not tilt, do not use disproportionate power and do not damage the receiver’s power
socket and its electrical connections when connecting the power cord. If the mains adapter
should fail to fit, contact your supplier.
FAILURE
If the mains adapter or the power socket or its electrical connection is damaged, immediately
unplug the mains adapter from the mains supply socket. Do not try to open or repair the mains
adapter or the receiver on your own! Service must be carried out only by experts at a proper
service centre.
If replacement parts are required, only original components are allowed to use. The use of
unauthorised components may result in risk of fire and electric shock.
Cleaning and care
Before cleaning, unplug the device from the mains adapter.
For cleaning the casing, please use a soft, damp cloth. Do not use any washing-up liquids that
aff ect the casing. Do not spray a cleaner towards the receiver
PLACEMENT
In touch with certain furniture surfaces it may happen that the receiver’s feet may rub off. You
should place the device on a proper underground that is stable and not easily inflammatory.
Otherwise the receiver may fall and cause serious injury to people and serious damages to the
device.
Do not use this product near water (e.g. bath tube, wash bowl, …).

Control elements, front and rear panel
5
Control elements, front and rear panel
1 4-digit display shows channel number
Display
-
Receiver in standby mode.
Channel number
Receiver is ON
rEC.
Timer activated
10 Smartcard reader
2 Connector for mains adapter 12VDC
3 TV-Scart port for connecting the TV
4 HDMI-Output (digital Audio- and Videosignal) for connecting the TV
5 USB-socket for external mass storage device (Option)
6 RF Input Digital –Socket for cable signal
7 RF loop through Output
Left side
8 Optical S/PDIF interface for DOLBY DIGITAL-Signal.
9 RJ-11-Socket: Connection for an External IR Receiver and Interf ace for
softwareupdate

Connecting the receiver
6
Connecting the receiver
RF (HF) connection
Connect the RF Input Digital socket (6) of the receiver to your cablesignal wall socket.
Connecting a television
Use a scart cable to connect the TV socket (3) on the receiver to the corresponding scart
socket on the television set.
HDMI output (4)
If your receiver is connected to the TV by a HDMI-cable, audio- and videosignal are digital.
Connecting a digital multi-channel amplifier
The receiver is optionally available with an AUDIO OUT socket (8) for a DOLBY DIGITAL signal.
Use a suitable cable to connect this socket to your multi-channel amplifier.
Connecting an External IR Receiver
If you want to set up the receiver where it can’t be seen, you can connect a so-called IR
mouse to the RJ-11 socket (9). This must be positioned in such a way that it can receive the
signals from the remote control. When installing the receiver, always be sure to follow the
safety and installation instructions.
Connecting an external mass storage device
For recording of TV programmes, an external mass storage device can be connected to the
optional USB-socket.
Connecting the mains adaptor
Connect the DC plug of the mains adaptor supplied with the unit to the socket DC-INPUT
+12V (2) on the receiver.
How to insert batteries into the remote control
Open the cover at the rear side of the remote control.
Insert two AAA type batteries (1.5V).
Attention: Take care of appropriate +/- polarity!
Note:
If the operational range of the remote control is getting smaller, it indicates that the batteries
are almost consumed. Always replace both batteries.
Caution:
Do not heat, disassemble or recharge the batteries.
Consumed batteries are not allowed to be disposed in domestic refuse. They must be supplied
to a facility, collecting and disposing exhausted batteries according to the EU environmental
protection rules.

Remote control
7
Remote control

Initial installation
8
Initial installation
After reading the safety instructions (see chapter “safety instructions)” and finishing the actions
explained in chapter “connecting the receiver” please use the supplied power cord for
connecting the apparatus to the power supply. When running the receiver for the first time the
“welcome menu” of the installation guide is displayed at the TV screen.
It helps you installing the most important settings.
Language of the menu
In the first step of the installation guide please select your
language
by using ▲or . Confirm your choice by OK.
Country
In the second step please select your country.
Therefore press ▲▼and then OK. If you want to get back to the
language selection, you have to use the EXIT button.
NOTE: The choice of the country affects the the channel list
sorting.
In the next step please select the parameters of your local
network ( use or ).
If you are not sure which type of modulation you have to use,
please select QAM-ALL for an automatic channel search.
Only the symbolrate (6.111MS, 6.875MS or 6.900MS) must be
selected.
Confirm with OK.
Language [1/8]
Welcome
Menu language [2/14]
Deutsch
English
Italiano
Suomi
Francais
Čeština
Türkçe
Welcome
Country [1/12]
Germany
Austria
Switzerland
Italy
Greece
Portugal
Hungary
Welcome
Network
6.900MS –QAM256
6.900MS –QAM64
6.900MS –QAM128
6.875MS –QAM256
6.875MS –QAM64
6.875MS –QAM128
6.111MS –QAM256
6.111MS –QAM64
6.111MS –QAM128
6.900 MS –QAM-ALL
6.875 MS –QAM-ALL
6.111 MS –QAM-ALL

9
Sort channels
In the last step of the initial installation you are asked, if the
channels which are found during the channel search, should be
sorted automatically.
Note: This function is only effective, if accordant channel
list informations are sent by the broadcast-station.
Use the buttons or to select NO or YES and confirm with OK.
The menu for automatic channel search and the search process will be started. During the
search the window shows Status: “scanning”. The newly found TV and radio programmes will
be listed. Once the search is complete, the message Status: “complete” is shown.
Use EXIT to leave the search menu.
Welcome
Sort channels?
No
Yes

Operating the receiver
10
Operating the receiver
Switching receiver ON/OFF
1.) This receiver is equipped with a low power standby circuit.
If this function is activated, the standby power consumption of the receiver is less
than 1W.
The function is switched ON or OFF in the menu SETTINGS/RECEIVER SETUP.
Low-Power Standby ON –Switching on the receiver takes about 10 seconds
(Display: “boot”).
Low-Power Standby OFF –Receiver switches ON immediately.
2.) The receiver is also equipped with the function „Auto-Standby“.
This function can be activated or deactivated in the menu SETTINGS/RECEIVER
SETUP.
If “Auto-Standby“ is activated, the receiver switches to Standby-Mode after 3 hours
running. Precondition:No timer is activated and no operations with the remote control
during this time.
You can switch on the receiver by pressing , OK,▼or by using one of the numeric
buttons 1…0. The last activated channel will be displayed (e.g. 0015).
The digital receiver is switched into standby mode by pressing .
ATTENTION: Only by pulling the mains adapter the receiver is disconnected from the
power supply completely.
TV & Radio mode
You can choose between the operation mode TV (viewing TV channels) and RADIO (listening
to radio channels) by pressing TV/R.
Volume control & Muting
The volume level can be adjusted by pressing ◄ ► or VOL . The corresponding scale is
displayed on the screen.
Hint:
- It is not possible to change the volume level while the menu is active.
- The volume control only affects the audio output at the TV, VCR and AUDIO
ANALOG OUT ports of the receiver.
By pressing the button you can totally switch off the audio output (muting). For switching on
again, simply use the same button.

Operating the receiver
11
Selecting a channel
1. Using the directional up/down keys
To change the channels stepwise press the buttons . In order to switch the
channels quicker hold these buttons pressed longer.
2. Using the numeric keys (direct input)
One or more digit channel numbers can be input by using the numeric buttons 0…9
and pressing OK. Not available channel numbers are ignored.
3. Using the channel list
By pressing the LIST button the last activated channel list or favourite list is
displayed. Browse the channel list by pressing ◄ ► or and activate the
desired channel by pressing OK.
When pressing key LIST twice the following menu appears:
Favourites List: Your personal list of favourite channels
Radio List: List of stored Radio channels
TV List: List of stored TV channels
Alphabetic List: List of stored TV or RADIO channels in alphabetical order.
Choose the favoured list by pressing and activate it by pressing OK.
In alphabetic list mode the channels are sorted alphabetically. It helps you searching a
certain channel. Therefore press LIST for displaying the alphabetic channel list and its char
locator. Then enter the char locator menu by pressing . Use and ◄ ► for selecting
the first letter of the searched channel and confirm by OK. If available the channel list
shows the wished channel now.
For re-entering the channel list press , for activating the channel use OK.
4. Swap from current channel to the previous one:
Your receiver remembers the previous activated channel:
- By pressing you can switch from the current to the previous channel
- By pressing again switch back to the current channel
Every time you perform a channel change, the title and start/stop time of the current and the
following programme are displayed in the channel change OSD (on screen display).
Thereby the scale of progression below the programme number signals the temporal
progress of the current programme.
If faded out you can display this information again by pressing OK.
Favourites list
Radio list
TV list
Alphabetic list
Select list

EPG –Electronic Programme Guide
12
EPG –Electronic Programme Guide
Almost all TV and radio broadcasters provide further information on their programme. Your
receiver stores and decodes these data and displays them in the so called Electronic
Programme Guide (EPG).
This programme preview is activated by using the EPG button. The appearing list contains all
programmes of the current channel.
In the headline of the menu channel name, date and time are shown.
By using the buttons the channel can be changed without leaving the EPG-menu.
With or ◄ ► you can select the broadcast you want to be informed about. You can get
more detailed information by pressing OK.
Also you can use the EPG list to program a record timer very easily: Just press the Record
button and activate the record timer in the corresponding menu.
Please use EXIT to leave this on screen dialog.
Settings
The basic functionality of the receiver is defined in the Settings menu.
The derivation of your local time against the GMT (Greenwich Mean time) time needs to be
corrected, otherwise the displayed times may be wrong.
Hint:
At each on screen display the possible user inputs are explained in the help bar at the lower
screen brink.
By pressing ◄ and ► you can change the corresponding settings. When leaving a menu
(EXIT button) you will be asked to store the performed modifications (Yes) or to keep the
previous settings (No). Please choose one of these possibilities by pressing ◄ and ► and
confirm your choice by OK.
Turn on the receiver by pressing .
For entering the main menu, please press the MENU button.
The main menu is displayed:
Note: “Mass Storage Device” is only displayed, when an external
mass storage device is connected at the USB-Socket of the
receiver.
Das Erste HD
20:07
Monday 19 .12.2011
Main menu
Settings
Installation
Channel list
Timer
Information
Mass Storage Device

Settings
13
Press the OK button.
The following menu is displayed:
Choose the menu item Receiver Setup by pressing and
confirm by OK.
Settings –Receiver setup
The following menu is displayed:
1) Time difference
When operating the receiver for the first time you should set the derivation between your
local time and the received GMT time (Greenwich Mean Time) by pressing ◄ or ►.
For Central Europe the following settings are recommended:
Winter time: +1.00 hour
Summer time: +2.00 hours
Note: This setting has to be updated at each summertime shift.
2) Menu language
Choose your language by pressing ◄ or ►.
3) Initial volume
The initial volume after a power reset of the receiver is adjusted here by pressing ◄ or ►.
4) HDMI Audio Bitstream
HDMI Audio Bitstream can be switched ON or OFF by pressing ◄ or ►.
5) Auto Standby
Auto-Standby function can be switched ON or OFF by pressing ◄ or ►.
6) Low-Power Standby
Low-Power Standby function can be switched ON or OFF by pressing ◄ or ►.
Settings
Receiver setup
Picture
Sound
Subtitle
OSD configuration
Parental lock
Receiver setup
Time difference
Menu language
Initial volume
HDMI Audio Bitstream
Auto Standby
Low-Power-Standby
+2.00 Std.
English
90%
Off
On
On

Settings
- 14 - - 14 -14
Settings –Picture
For entering the Picture menu, select menu item Picture in the Settings menu and press OK.
The following menu appears:
1) Analog Video
The analog video output at the SCART socket
can be adjusted by pressing ◄ or ►. You can
select among following options: FBAS, RGB, or
YUV.
2) Digital Video
The digital video output at the HDMI socket can
be adjusted by pressing ◄ or ►. You can
select among following options: YcbCr or RGB.
3) Display format
Use ◄ or ► for selecting the screen format of your TV set (4:3, 16:9).
4) Display adjustment
Use ◄ or ► for adjusting the video signal: pan & scan, letterbox or pillar box.
5) Videosystem
Use ◄ or ► for adjusting the video system: AUTO, PAL, NTSC.
6) Picture scaling
Here you can choose the picture resolution.
720 x 576
1280 x 720
1920 x 1080
a.) Television connected to Scart-Socket:
If your TV is only connected to the scart-socket of the receiver, you get the best picture quality,
if you choose in the menu item „Picture scaling“ 720x576 for all output signals.
b.) Television connected to HDMI-Socket
If your TV is only connected to the HDMI-socket of the receiver, you get the best picture
quality, if you choose in the menu item „Picture scaling“ Input signal = Output signal.
If you prefer fast channel switching, all output signals must be the same.
Press EXIT to leave this menu. For storing your modifications select Yes (◄ or ►), for
keeping the previous settings select No.
Confirm your choice by pressing the OK button.
Analog Video
Digital Video
Display format
Display adjustment
Videosystem
Picture scaling:
>Input 720x576
>Input 1280x720
>Input 1920x1080
RGB
YCbCr
16:9
Letterbox
Auto
Output 1280x720
Output 1280x720
Output 1280x720
Picture

Settings
- 14 - - 14 -14
Settings –Picture
For entering the Picture menu, select menu item Picture in the Settings menu and press OK.
The following menu appears:
1) Analog Video
The analog video output at the SCART socket
can be adjusted by pressing ◄ or ►. You can
select among following options: FBAS, RGB, or
YUV.
2) Digital Video
The digital video output at the HDMI socket can
be adjusted by pressing ◄ or ►. You can
select among following options: YcbCr or RGB.
3) Display format
Use ◄ or ► for selecting the screen format of your TV set (4:3, 16:9).
4) Display adjustment
Use ◄ or ► for adjusting the video signal: pan & scan, letterbox or pillar box.
5) Videosystem
Use ◄ or ► for adjusting the video system: AUTO, PAL, NTSC.
6) Picture scaling
Here you can choose the picture resolution.
720 x 576
1280 x 720
1920 x 1080
a.) Television connected to Scart-Socket:
If your TV is only connected to the scart-socket of the receiver, you get the best picture quality,
if you choose in the menu item „Picture scaling“ 720x576 for all output signals.
b.) Television connected to HDMI-Socket
If your TV is only connected to the HDMI-socket of the receiver, you get the best picture
quality, if you choose in the menu item „Picture scaling“ Input signal = Output signal.
If you prefer fast channel switching, all output signals must be the same.
Press EXIT to leave this menu. For storing your modifications select Yes (◄ or ►), for
keeping the previous settings select No.
Confirm your choice by pressing the OK button.
Analog Video
Digital Video
Display format
Display adjustment
Videosystem
Picture scaling:
>Input 720x576
>Input 1280x720
>Input 1920x1080
RGB
YCbCr
16:9
Letterbox
Auto
Output 1280x720
Output 1280x720
Output 1280x720
Picture
Settings
- 15 - - 15 -15
Settings –Sound
1) Sound setting
Using ◄ or ► you can activate following audio modes: Stereo, Mono left or Mono right.
2) Sound channel TV
If the broadcasted programme offers different audio options you can select the desired
audio output at the TV Scart by keys ◄/►.
3) Sound channel digital
If the broadcasted programme offers a digital audio channel, you can use ◄/► for selecting
the audio signal that is to be output at the digital audio port.
Press EXIT to leave the menu. If you want to save your modifications choose Yes, for
restoring the previous parameters choose No (keys ◄/►).
Confirm your choice by pressing the OK button.
Settings –Subtitle
1) Subtitle
By using ◄/► you can activate/deactivate the display of DVB subtitles (if transmitted).
2) Language of the subtitle
To select the language of the subtitle you must use ◄ or ►. If there is no subtitle available
this is indicated by “-“.
By default the subtitle is in accordance with the menulanguage.
Use EXIT to leave the menu. If you want to save the modifications choose Yes, for restoring
the previous parameters choose No (keys ◄/►).
Confirm your choice by pressing the OK button.
Settings –OSD Configuration (Option)
Sound
Sound settings
Sound channel TV
Sound channel Dig.
Stereo
Stereo
Uncompressed (PCM)
Subtitle
Subtitle
Subtitle language
Off
-

Settings
- 16 -
- 16 -16
For entering the OSD configuration menu, please select menu item OSD configuration in the
Settings menu and press OK. The following menu appears:
1) Display time:
By using ◄ or ► you can modify the display duration of the channel change graphics (1-10
seconds).
2) OSD colour:
You can choose the colour of the OSD display by pressing ◄ or ► .
Press EXIT to leave this menu. If you want to store your modifications select Yes by
pressing ◄ or ►. For the restoring the previous settings you have to choose No.
Confirm your choice by using OK.
OSD Configuration
Display time
OSD colour
5 s
blue

Settings
- 17 - - 17 -17
Settings –Parental lock
Your receiver is equipped with a parental lock. This secures the receiver against unauthorised
use. When the parental lock is activated, the receiver can only be switched on after entering a
4-digit PIN code.
In the Main menu, use the ▲▼ buttons to move the cursor to the
line Parental lock and press the OK button.
Parental lock –device lock
To activate or deactivate the device lock, move the cursor to
the line Device lock and press OK. The following menu will
appear:
Use the ◄► buttons to switch the device lock on or of. When the lock is activated, the PIN
code must be entered when switching on the receiver.
Press EXIT to leave the menu. Use the ◄► buttons to choose whether you want to store the
changes made (Yes) or keep the previous settings (No). Confirm your choice with the OK
button.
Parental Lock –changing the PIN
To change the PIN code, move the cursor to the line
Change Pin and press OK. The following menu will appear:
The PIN code is set at the factory to 0000. Using the code 9976, the receiver can always be
switched on, regardless of what PIN code has been set.
Use the ▲▼ buttons to move the cursor to the line New PIN and press the OK button. Use
the 0-9 buttons to enter a 4 digit PIN code, the press OK. Use the ▼ button to move the
cursor to the line Confirm PIN and press the OK button. Now confirm your entry by entering
your chosen PIN code one more time, then press OK.
Press Exit to leave the menu. Use the ◄► buttons to choose whether you want to store the
changes made (Yes) or keep the previous settings (No). Confirm your choice with the OK
button.
WARNING
You must not forget the PIN code. Should this happen, please contact your specialist dealer!
Parental Lock
Device Lock
Change PIN
Device Lock
Lock Device
No
Change PIN
New PIN
Confirm PIN
* * * *
* * * *

Installation
- 18 - - 18 -18
Installation
In the main menu, select the line Installation using
▲ ▼ and confirm with OK. The Installation menu
will appear:
Use the buttons to make your selection and
confirm with OK.
Installation –channel search
You can choose between automatic (antenna) and manual (transponder) channel search.
The automatic channel search checks the whole VHF and UHF range for programmes you
can receive.
Automatic channel search
In the Installation menu, move the cursor using the buttons onto the line Channel search
and press the OK button. The following menu will appear:
Performing an automatic channel search
Select the line Antenna using and Terrestrial using the ◄ or ► buttons.
Select the line Search mode using and Antenna using the ◄ or ► buttons.
In the line Encrypted, select whether the channel search should also include encrypted
channels, using the ◄ or ► buttons.
No = encrypted channels will be ignored.
Yes = encrypted channels will be included in the search.
Move the cursor onto the line Start scan using the buttons and start the search process
by pressing the OK button.
Now two windows are shown, listing the newly found TV and radio programmes. The “Status”
window shows how far the search has progressed.
- Display: Scanning => Search is active
- Display: Complete => Search is finished.
You can leave this menu by pressing EXIT. If not finished, the channel search algorithm is
aborted. If new channels are found, you are asked to store them (Yes). Select your choice by
◄/► and confirm with OK. If selected YES the new channels are stored at the end of the
channel list now.
Installation
Channel search
Factory reset
Channel search
Antenna
Search mode
Encrypted
Modulation
Symbolrate
Cable
automatically
No
QAM 64
6.900MS
Start scan

Installation
- 19 -
- 19 -19
Manual channel search
In manual channel search, you can enter the channels to be searched directly.
In the Installation menu, move the cursor using the buttons onto the line Channel search
and press the OK button. The following menu will appear:
This is how to perform a manual channel search:
Select the line Antenna using and Terrestrial using the ◄ or ► buttons.
Select the line Search mode using and Transponder using the ◄ or ► buttons.
In the line Encrypted, select whether the channel search should also include encrypted
channels, using the ◄ or ► buttons.
No = encrypted channels will be ignored.
Yes = encrypted channels will be included in the search.
In the line Frequency, use the ◄ ► buttons to select the channel that should be searched.
Move the cursor onto the line Start channel search using the buttons and start the search
process by pressing the OK button.
Now two windows are shown, listing the newly found TV and radio programmes. The “Status”
window shows how far the search has progressed.
- Display: Scanning => Search is active
- Display: Complete => Search is finished.
You can leave this menu by pressing EXIT. If not finished, the channel search algorithm is
aborted. If new channels are found, you are asked to store them (Yes). Select your choice by
◄/► and confirm with OK. If selected YES the new channels are stored at the end of the
channel list now.
Installation –Factory reset
This menu item allows you to reset the receiver to its default factory status. Afterwards the
receiver starts up with the Welcome Screen (initial installation) again.
Channel search
Antenna
Search mode
Encrypted
Modulation
Symbolrate
Channel
Cable
manually
No
QAM 64
6.900MS
7 (191.5MHz)
Start scan

- 20 - - 20 -20
Installation –Smartcard Reader
The Digital-Receiver is optionally equipped with a smartcard reader.
With an equal smartcard it is possible to unscramble encoded channels.
The smartcard can be inserted also while the receiver is switched on.
Insert the smartcard (golden chip on lower side towards the receiver) carefully into the slot at
the front panel of the receiver.
To open the menu of the smartcard, first select “Installation” in the main menu and press OK
to confirm.
A submenu generated by the smartcard appears
on the screen. Conax or CryptoGuard.
Select the submenu of the smartcard with or and
press OK to confirm.
For more information on using the smartcard, see the menus
shown or it´s instruction manual.
After the smartcard is inserted, the encoded
programmes will be unscrambled.
Installation
Channel search
Factory reset
Software download
Conax