Tricam MH1640 User manual

OWNER'S MANUAL
Model MH1640
Wheelbarrow
9 Cubic Foot
• Important Safety Instructions
• Assembly Instructions
• Parts and Hardware Identification
Tricam International
7677 Equitable Drive
Eden Prairie, MN 55344
800-304-1316
Read, understand and follow ALL instructions before using this product
CAUTION:

STEP 1 Place tray upside-down to access the bolt
mounting slots.
STEP 2 Insert M8x150mm carraige bolts into tray
slots in the middle of the tray and
M8x100mm carraige bolts into the two tray
slots at the rear of the tray.
STEP 3 Install left and right wood spacers by
positioning the spacers with the notches
down. The thickest end of the spacer should
be positioned towards the front of the tray.
STEP 4 Install left and right handles. Make sure that
the left and right identification marks are on
the proper sides.
STEP 5 Install left and right legs. Place a flat washer
and lock washer on each bolt; retain the
installed hardware by hand tightening a nut
on each bolt.
STEP 6 Install leg brace with M8x20mm machine
screw, flat washer, lock washer and nut at
each end of the brace.
IMPORTANTANT SAFETY INSTRUCTIONS
1. Read and understand all warning and instructions prior to using the wheelbarrow.
2. Always inspect the wheelbarrow for damage or excess wear prior to each use.
3. Never transport people using this wheelbarrow.
Your Wheelbarrow requires assembly. Account for all parts and hardware before beginning assembly. If any parts are
missing, damaged or if you have questions or need additional instructions DO NOT RETURN THIS
PRODUCT TO THE RETAILER, call the manufacturer at 1-800-304-1316.
Refer to the parts list on the following pages during assembly.
Do not tighten nuts until you have completed
assembly of all parts!
2 Right
2 Left
5 Left
5 Right
front rear
1
15
16
front rear
figure 1
3 Left
3 Right
4
17
18
18
19 11
figure 2
19
Left
Side
Right
Side
ASSEMBLY INSTRUCTIONS
Your Wheelbarrow requires assembly. Account for all parts and hardware before beginning assembly. If any parts are
missing, damaged or if you have questions or need additional instructions, DO NOT RETURN THIS
PRODUCT TO THE RETAILER, call the manufacturer at 1-800-304-1316.
Refer to the parts list on the following pages during assembley.

STEP 7 Install nose guard with M8x50mm machine screws.
Insert the screws from the inside of the handles so
the washers and nuts are outside the handles.
STEP 8 Insert the axle through the axle mounts, one on
each end of the axle. Position asssembly over
mounting holes in the handles and install
M8x80mm machine screws. Slide wheel washer
over each end of the axle. Slide one wheel over
each end of the axle. Slide one wheel washer over
each end of the axle and secure with cotter pin.
STEP 9 Install tray braces with remaining M8x80mm
machine screws. Pass screws through handle,
apply washers and hand-tighten nuts.
Install M8x20mm carriage bolts into the
front T-slots of the tray. Install right and left
tray brace ends onto the tray bolts. Apply
washers and hand-tighten nuts.
STEP 10 Tighten all nuts securely
with wrench.
12
8
19
17
18
14
19
17
18
Front hole
6 Right
6 Left
14
19
17
18
7
20
21
17
18
13
19

PARTS LIST
1 Tray - (1)
2 Wood Handles - (2)
3 Legs - (2)
4 Leg Brace - (1)
5 Notched Wood Spacers - (2)
6 Axle Mounts - (2)
7 Axle - (1)
8 Tray Braces - (2)
9 Nose Guard - (1)
10 Tire - (1)
11 M8x20mm Slotted Bolts - (2)
 for leg brace
12 M8x20mm Carriage Bolts - (2)
 for tray braces
13 M8x50mm Carriage Bolts - (4)
 for nose guard
14 M8x80mm Carriage Bolts - (4)
 for axle mounts
15 M8x100mm Carriage Bolts - (2)
 for rear of tray
16 M8x150mm Carriage Bolts - (2)
 for middle of tray
17 Hex Nuts - (16)
18 Lock Washers - (16)
19 Flat Washers - (16)
20 Wheel Washers - (4)
21 Cotter Pin - (2)
PARTS & HARDWARE
IDENTIFICATION