Tricam MH1650 User manual

OWNER'S MANUAL
Model MH1650
Wheelbarrow
10 Cubic Foot
• Important Safety Instructions
• Assembly Instructions
• Parts and Hardware Identification
Tricam International
7677 Equitable Drive
Eden Prairie, MN 55344
800-304-1316
Read, understand and follow ALL instructions before using this product
CAUTION:

IMPORTANTANT SAFETY INSTRUCTIONS
1. Read and understand all warning and instructions prior to using the wheelbarrow.
2. Always inspect the wheelbarrow for damage or excess wear prior to each use.
3. Never transport people using this wheelbarrow.
Do not tighten nuts until you have completed
assembly of all parts!
ASSEMBLY INSTRUCTIONS
Your Wheelbarrow requires assembly. Account for all parts and hardware before beginning assembly. If any parts are
missing, damaged or if you have questions or need additional instructions, DO NOT RETURN THIS
PRODUCT TO THE RETAILER, call the manufacturer at 1-800-304-1316.
Refer to the parts list on the following pages during assembley.
STEP 1 Place both handles on sawhorses or similar
stand to firmly support the wheelbarrow
during assembly.
STEP 2 Align the long and short cross braces over
the handle machine screw holes.
STEP 3 Insert M8x85mm machine screws thru each
hole in the bottom of the tray. Position the
tray machine screws so the screws align to
go thru the long and short braces and the
handles.
STEP 4 Attach the right and left legs onto each set
of machine screws using washers, lock
washers and nuts. Finger-tighten only.
STEP 5 Install leg brace with M8x20mm machine
screw, flat washer, lock washer and nut at
each end of the brace.
15 & 16
3
23
22
3
19
18
17
2
17
18
19
3
11
3
22
4
1

STEP 7 Install tray braces to front holes in tray with
M8x20mm machine screws, washer, lock washer
and nut. Finger-tighten only.
STEP 8 Insert four M8x80mm machine screws through
the holes in the top front of the handles.
Note: Two of the screws go through the bottom
holes of the tray support braces first. Install both
axle mounts. Finger-tighten assembly with
washers, lock washers and nuts.
STEP 11 Tighten all nuts securely
with wrench.
STEP 9 Pre-assemble tubular tray brace. Place
U-shaped tray tube under the front lip of
the tray. Align the bottom holes of the tubular
braces with the front holes of the nose guard.
Install screw, washer, lock washer and nut.
Tighten all nose guard screws with wrench
and screwdriver.
STEP 10 Slide axle through both axle mounts, centering
axle to handles.Slide wheel washer over each
end of the axle. Slide one wheel over each end
of the axle. Slide one wheel washer over each
end of the axle and secure with cotter pin.
STEP 6 Install nose guard with M8x50mm machine
screws. Using only the front screw holes in
the handles first, install the screws thru the
nose guard into the handles. Place washer,
lock washer and nut on each bolt and only
finger-tighten.
12
8
19
17
18
14
19
17
18
Front hole
17
18
13
19
19
18
17
24
25
13
7
20
20
21

PARTS LIST
1 Tray - (1)
2 Wood Handles - (2)
3 Legs - (2)
4 Leg Brace - (1)
5 Notched Wood Spacers - (2)
6 Axle Mounts - (2)
7 Axle - (1)
8 Tray Braces - (2)
9 Nose Guard - (1)
10 Tires - (2)
11 M8x20mm Slotted Bolts - (2)
 for leg brace
12 M8x20mm Carriage Bolts - (2)
 for tray braces
13 M8x50mm Carriage Bolts - (4)
 for nose guard
14 M8x80mm Carriage Bolts - (4)
 for axle mounts
15 M8x85mm Carriage Bolts - (2)
 for rear of tray
16 M8x85mm Carriage Bolts - (2)
 for middle of tray
17 Hex Nuts - (16)
18 Lock Washers - (16)
19 Flat Washers - (16)
20 Wheel Washers - (4)
21 Cotter Pins - (2)
22 Cross Brace (short) - (1)
23 Cross Brace (long) - (1)
24 Tray Support Tubes - (2)
25 Tray Tube - (1)
PARTS & HARDWARE
IDENTIFICATION