TrickleStar 601CC-US-W User manual

601CC-US-W
www.tricklestar.com
HUMIDITY CONTROLLER
601CC-US-W
INSTRUCTIONS (ENGLISH)
Introduction
Thank you for purchasing this TrickleStarTM product. This product
provides enhanced controls to reduce wasteful energy
consumption of dehumidifying, humidifying and heating
appliances, which do not include humidity controls. This product is
suitable for the control of devices such as dehumidifiers,
humidifiers and electrical heaters.
LCD Display
Factory Default Setting
The factory default settings are:
Dehumidify Mode and a humidity “SET POINT” of 40%.
Status Indication
Off
Product is OFF
Green
Product is ON and Control Socket is ON
Red
Product is ON and Control Socket is OFF
Application / Installation
Plug the product into a wall outlet and plug an appliance to be
controlled into the Control Socket.
Select Dehumidify / Humidify Mode
To switch between Dehumidify and Humidify Modes, switch the
product OFF using the Button.
Press the button and button simultaneously for 3 seconds to
switch between Dehumidify and Humidify Mode.
Dehumidifying Mode Setup
1. Select Dehumidify Mode.
2. Press button to switch product ON.
3. Press or button to adjust to the required humidity Set-
point.
Dehumidifying Mode Operation
When room humidity is higher than the Target Set-point
, the Status Indicator will illuminate GREEN and the Control
Socket will switch ON within 3 min.
When room humidity is lower than the Target Set-point ,
the Status Indicator will illuminate RED and the Control Socket will
switch OFF within 3 minutes.
Humidifying Mode Setup
1. Select Humidify Mode.
2. Press button to switch product ON.
3. Press or button to adjust the humidity Set-point.
Humidifying Mode Operation
When room humidity is lower than the Set-point , the
Status Indicator will illuminate GREEN and the Control Socket will
switch ON within 3 min.
When room humidity is higher than the Set-point the
Status Indicator will illuminate RED and the Control Socket will
switch OFF within 3 minutes.
Down Button
On / Off Button
Status Indicator
Reset Button
LCD Display
Control Socket
Up Button
Humidity Sensor
RM SET
80
Room Humidity De-Humidify Mode
Humidify Mode
Target Humidity
Set-point
Set Humidity
Set-point
Percentage
%
88 8
.%
SET
De-Humidify
Humidify
SET
SET
SET
SET

601CC-US-W
www.tricklestar.com
Restore Factory Defaults
Press the Reset Button for 2 seconds to restore factory defaults.
Battery
The product contains a rechargeable battery to store settings if
power is removed.
If the battery level is low, a “LO” icon will flash in the display.
Connect the product to a power outlet for 1 hour to recharge the
battery. If the battery is fully discharged, the factory defaults will be
restored.
Electrical and Environmental Specifications
Voltage
125 VAC / 60Hz
Power Rating:
16A / 3680W – Resistive
Load
2A / 460W – Inductive Load
Humidity Control Range
10% - 90% N/C
Humidity Measuring Range
10% - 90% N/C
Measurement interval
10 sec.
Switching hysteresis
Up to 3 minutes
Operating Temperature
-10° to 40°C
Storage Temperature
-10ºC to 70ºC
Storage Humidity
5 to 95% N/C
IMPORTANT SAFETY NOTICES
•Fans or other appliances with exposed elements should not
be left unattended.
•FOR INDOOR USE ONLY
•SUITABLE FOR NON-CONDENSING ENVIRONMENTS
ONLY.
Approvals
US ELECTRICAL & SAFETY
OTHER
ETL
2002/95/EG (RoHs)
2002/96/EC (WEEE)
1999/5/EC (RTTE)
Warranty
www.tricklestar.com/warranty
Copyright & Disclaimer
© TrickleStar Ltd. All rights reserved.
TrickleStarTM is a registered trademark of TrickleStar Ltd.
Disclaimer: TrickleStar reserves the right to change specifications
or designs described in this manual without notice and without
obligation. Any typographical, clerical or other error or omission in
this document or other documents or information issued by
TrickleStar shall be subject to correction without any liability on the
part of TrickleStar without notice.
Conserving Energy. Improving Life.
www.tricklestar.com