Tridium VYKON NPB-LON Assembly instructions

3951 Westerre Parkway, Suite 350
Richmond, Virginia 23233 USA
NPB-LON Option
INSTALLATION SHEET
NPB-LON Option Installation Sheet
Part Number 10620 Rev. 2 Updated:May29, 2009 1
Information and specifications published here are current as of the date of publication of this document. Tridium, Inc. reserves the right to change or modify
specifications without prior notice. The latest product specifications can be found by contacting our corporate headquarters, Richmond, Virginia. Products or
features contained herein may be covered by one or more U.S. or foreign patents. © 2009 Tridium, Inc.
Thisdocumentcoversthemountingandwiringofthe
NPB‐LON1optioncardinaVykon®JACEcontroller
(JACE‐200/600,SEC‐J‐x01,orJ‐202‐XPRseries).
RefertotheappropriateJACE®mountingandwiring
documentforfurtherJACEinstallationdetails.
Included in this Package
Includedinthispackageyoushouldfindthe
followingitems:
•NPB‐LONoptioncard,connectorendplate.
•one2‐positionterminalplug,forwiringtoan
FTT‐10LonWorks®network
•ThisNPB‐LONOptionInstallationSheet,Part
Number10620Rev.2
Material and Tools Required
Thefollowingtoolsandsuppliesmayberequiredfor
installation:
•#2phillipsscrewdriver:toinstalltheNPB‐LON.
•Smallflat‐bladescrewdriver:tomakewiring
connectionstotheFTT‐10Lonworksnetwork.
•#1phillipsscrewdriver:toremoveandrefasten
J‐202‐XPRcovers(ifapplicable).
Figure 1 NPB-LON option.
Mounting
Warning PowertotheJACEmustbeOFFwhen
installingorremovingoptioncards,or
damagewilloccur!Also,youmustbevery
carefultopluganyoptioncardintoits
connectorproperly(pinsaligned).
MounttheNPB‐LONoptioncardineitherofthe
optioncardslotsoftheJACE,asneeded.Notethe
J‐202‐XPRserieshasonlyoneoptioncardslot.
Procedure 1 Mounting NPB-LON option card on a JACE.
1. Remove powerfromtheJACE—seetheprevious
Warning.WaitforallLEDsontheunittobeOff.
2. RemovetheJACEcoverorcovers(J‐202‐XPR).
ForallbuttheJ‐202‐XPR,pressinthefourtabson
bothendsoftheunit,andliftthecoveroff.
Note Ifaccessorymodulesarepluggedintothe
JACE,youmayneedtoslidethemawayfrom
theunittogettothecovertabs.
FortheJ‐202‐XPR,firstremovetherightcover,
thentheleftcover,retainingthetwoscrewsthat
secureeachcover.
1. LON and LonWorks are registered trademarks of the Echelon
Corporation.
Table 1 NPB-LON option description.
Description Notes / LON Port Assignments
FTT-10A LON
(LonWorks)
adapter with a
2-position
removable
screw-terminal
connector
plug.
Up to 2 LON®option cards may be installed
(note that the J-202-XPR series controller
accepts only one option card).
•If one LON option, it operates as LON1,
regardless of Option slot.
•If two LON options, LON1 is Option slot 1,
LON2 is Option slot 2.
See Figure 2 on page 2 for location of
Option Slots 1 and 2 on a JACE-200/600.
NOL
XTXR

NPB-LON Option Installation Sheet
Updated: May 29, 2009 Part Number 10620 Rev. 2
Wiring
Material and Tools Required
2
3. ForallbuttheJ‐202‐XPR,removethebatteryand
bracketassemblybytakingoutthescrews
holdingitinplace,settingthescrewsasidefor
later.Unplugthebatteryfromtheconnectoron
theJACE.SeeFigure 2foranexplodedview.
Figure 2 Remove battery assembly.
4. Removetheblankingendplatefortheslotyouare
installingtheoptioncardinto.
(Retaintheblankingendplateincasetheoption
cardmustberemovedatalaterdate.)
5. CarefullyinsertthepinsoftheNPB‐LONintothe
socketoftheappropriateoptioncardslot.The
mountingholesontheoptionboardshouldline
upwiththestandoffsonthebaseboard.Iftheydo
not,theconnectorisnotproperlyaligned.Press
untiltheoptioncardiscompletelyseated.
6. Placethecustomendplatethatcamewiththe
NPB‐LONoveritsconnector(seeFigure 3).
Figure 3 NPB-LON inserted, end plate on top.
7. Plugthebatterycableintothebatteryconnector
ontheJACE(Figure 3showsthelocationofthe
batteryconnectorontheJACE‐200/600).
8. ForallbuttheJ‐202‐XPR,setthebatteryand
bracketassemblybackovertheoptioncardslots,
withmountingholesalignedwiththestandoffs.
Screwsenterholesinthebatterybracketfirst.
Figure 4 Re-fasten screws.
9. Placethescrewsthroughtheendplate(s),andinto
thestandoffsonthebaseboard.Usinga
screwdriver,handtightenscrews.
10. ReplacetheJACEcoverorcovers(J‐202‐XPR).
Ifaccessorymoduleswereunpluggedfromthe
JACE,plugthembackasbefore,andsecure.
Wiring
ConnectLonWorksFTT‐10communicationswiringto
the2positionconnectoroftheNPB‐LON.Notethat
polarityisnotafactorinFTT‐10wiring.
RefertotheLonWorksFTT‐10AFreeTopology
TransceiverUser’sGuide(078‐0156‐01F)fortechnical
guidelinesassociatedwithfreetopologyrestrictions,
andtheJunctionBoxandWiringGuidelinesforTwisted
PairLonWorksNetworks(005‐0023‐01)formore
detailedinformationonwiringspecifications.These
documentsareavailableonEchelon’swebsite
(www.echelon.com).
LEDs
TwoLEDsarevisibleonthetopoftheNPB‐LON
optioncard(covermustberemovedfromJACE):
•RX(green)—Receive,indicatesthatanother
LonWorksdeviceistransmittingamessage.
•TX(yellow)—Transmit,indicatesthattheJACE
istransmittingamessageontheLONtrunk.
TheseLEDsareincludedonthetoplabelofthethe
NPB‐LON,seeFigure 1.
Screws (4)
Option Slot 2
Area
Blanking
End
Plate
Battery
Assembly
(includes
cable and
bracket)
Unplug battery here
Option Slot 1
Area
JACE-200/600
JACE
Battery
Connector
Place NPB-LON custom
end plate over end.
Insert NPB-LON into
option card slot carefully,
with pins aligned.
Fully seat card. JACE-200/600
For JACE models
with battery
assembly over the
Option Slots,
reinsert the
4 screws through
thebatterybracket,
endplates,andinto
the standoffs. JACE-200/600