Tripp Lite B126-1A1-PLHD User manual

1
Owner’s Manual
HDMI over Powerline
Active Extender Kit
Model: B126-1A1-PLHD
Español 8 • Français 15
Do not plug this unit into an extension cord, power strip,
surge protector, or outlet with a Ground Fault Circuit
Interrupter (GFCI) or Arc Fault Circuit Interrupter (AFCI)
circuit.
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
Copyright © 2018 Tripp Lite. All rights reserved.
18-02-433-933756.indb 1 4/11/2018 8:06:22 AM

2
Package Contents
Optional Accessories
System Requirements
Product Features
• Transmitter Unit
• Receiver Unit
• IR-IN Cable
• IR-OUT Cable
• (2) C7 to NEMA 1-15P Power Cords, 4 ft.
• Mounting Hardware
• Owner’s Manual
• P568-Series High-Speed HDMI Cables
• P569-XXX-LOCK* High-Speed HDMI Cables with Ethernet and Locking Connectors
*XXX refers to the length. Cables are available in 6 ft. (006), 10 ft. (010) and 15 ft. (015)
lengths.
• Source device with an HDMI port (Blu-ray player, computer, laptop)
• Display device with an HDMI port (HDTV, projector, monitor)
• 100–120V AC power input
• Extends HDMI audio/video and IR control signals up to 300 m (984 ft.) from the
source
• Uses existing power outlets to extend a 1080p signal up to 300 m @ 60 Hz
• IR control functionality for controlling the HDMI source device remotely
• HDMI output port on transmitter for connecting an additional display
• Supports high-definition video and stereo audio
• Supports 24-bit Deep Color (8 bits per channel)
• Compatible with HDMI 1.3 and HDCP 1.2 standards
• Supports 300 MHz/3.4 Gbps per channel bandwidth (10.2 Gbps total)
• Plug-and-play operation with no software or drivers required
18-02-433-933756.indb 2 4/11/2018 8:06:22 AM

3
Product Overview
Transmitter and Receiver Front Panel
Transmitter Back Panel
Receiver Back Panel
APower LED (Blue)—Illuminates to indicate the unit is receiving power.
BData Transmission LED (Yellow)—Blinks slowly while connection is building.
Blinks quickly when unit is successfully connected and transmitting data.
CConnection LED (Green)—Blinks when signal is connected.
DReset Button—Press to restart the unit.
EC8 AC Power Input—Connects to included 4 ft. C7 to NEMA 1-15P power cord.
FIR-OUT Connector (Female)—Connects to included IR-OUT cable. IR blaster
cable should be placed close to source device for best results.
GHDMI Output Connector (Female)—Connects to local HDMI display with HDMI
cable (sold separately).
HHDMI Input Connector (Female)—Connects to HDMI source with HDMI cable
(sold separately).
IC8 AC Power Input—Connects to included 4 ft. C7 to NEMA 1-15P power cord.
JIR-IN Connector (Female)—Connects to included IR-IN cable. Source remote
control must be within the required range of the IR receiver.
KHDMI Output Connector (Female)—Connects to local HDMI display with HDMI
cable (sold separately).
A
E
I
CB
F
J
D
G
K
H
18-02-433-933756.indb 3 4/11/2018 8:06:22 AM

4
Installation
Notes:
• Make sure all equipment being connected is powered off prior to installation.
This product requires that the transmitter and receiver be plugged into power
outlets that are on the same power circuit, and should not be connected
through an extension cord, power strip or surge protector. For optimal
performance, plug directly into a wall socket.
Connection issues may arise if the transmitter and receiver are connected to
an electrical circuit with a Ground Fault Circuit Interrupter (GFCI) or Arc Fault
Circuit Interrupter (AFCI), and if the power outlet is located near an appliance
with high power consumption, such as a washer or dryer. It is recommended to
avoid this if possible.
1. Optional: Attach the included mounting hardware to the transmitter and receiver
units, and mount them to a desired location.
2. Connect the HDMI source device to the HDMI Input port on the transmitter using
an HDMI cable, such as Tripp Lite’s P568-Series High-Speed HDMI Cables.
3. Connect an HDMI display to the HDMI output port on the transmitter using an
HDMI cable, such as Tripp Lite’s P568-Series High-Speed HDMI Cables.
4. Connect the IR-OUT (Tx) cable to the IR-OUT port on the transmitter.
Note: IR-OUT cable has IR-OUT marked on the bottom of the IR bulb. Place the bulb of the
IR-OUT cable in an area with a direct line of sight to the HDMI source device (e.g. Blu-Ray
player).
5. Connect an included AC power cord to the transmitter, and plug it directly into a
wall outlet.
6. Connect the HDMI display to the HDMI Output port on the receiver using a P568-
Series High-Speed HDMI Cable.
7. Connect the IR-IN (Rx) extension cable to the IR-IN port on the receiver unit.
Note: IR Receiver cable has IR-IN marked on the bottom of the IR bulb. Place the bulb of the
IR receiver cable in the general area you will be using the source device’s remote control.
8. Connect the other included AC power cord to the receiver, and plug it directly into
an electrical wall outlet.
9. Turn on power to the connected equipment.
DVD
IR
OUT
IR
IN
TVTV
Transmitter
HDMI Cable
Powerline
Receiver
18-02-433-933756.indb 4 4/11/2018 8:06:23 AM

5
Troubleshooting
If you are unable to get an acceptable image after following the installation
instructions, try the troubleshooting tips below.
1. Are the AC power cords that came with the product connected and
plugged into a working power source? For the product to function properly,
the transmitter and receiver must be connected to and receiving power from an
external power source.
2. Are the transmitter and receiver units plugged into power outlets that are
on the same electrical circuit? If not, they will not function properly.
3. Is the transmitter and/or receiver unit plugged into an extension cord,
power strip, or surge protector? If so, disconnect and plug the units directly
into a wall socket.
4. Are the transmitter and receiver connected to an electrical circuit with
a GFCI or AFCI, or connected to an outlet located near a high power
consumption device (e.g. washer, dryer, etc)? This may cause poor
performance, and you should try plugging into an outlet that avoids these things.
5. Was the power to the HDMI source turned off prior to installation? If not,
restart.
6. What resolution are you trying to reach? See the Product Features and
Installation sections in this manual for details on maximum distance and
resolution. If you are not able to get an acceptable image, try lowering your
computer’s video resolution or adjusting the refresh rate.
7. Does your HDMI display have a message saying “Waiting for Connection”
in the bottom right corner? If so, please check to make sure the AC power
cords are properly connected and the power indicator LEDs are solid.
8. Does your HDMI display have a message saying “Please Check the TX
Input Signal?” Please check that the HDMI signal connection on the transmitter
is solid. If the signal is not solid, connect the source device directly to the display
device to see if the issue is with the source, display or HDMI cable you are using.
9. Is the HDMI display transmitting a choppy picture? If so, make sure the
position of the transmitter and receiver are in the required range, and then press
the reset button on the receiver panel to reconnect. If this does not work, check
for other signal disturbances between the transmitter and receiver.
10. Test your cables to ensure they are working properly.
11. Are the transmitter and/or receiver located in an area that exposes them
to elevated temperatures? If the product is overheating, it will not function
properly.
18-02-433-933756.indb 5 4/11/2018 8:06:23 AM

6
Specifications
Warranty and Product Registration
Specification Value
Input Port HDMI (F); 3.5 mm (F)
Output Port (x2) HDMI (F); 3.5 mm (F)
IR Frequency 20–60 Hz Wide Range
Transmission Distance 300 m (984.3 ft.)
Voltage AC 100–120V
Power Consumption Tx: 7.5W; Rx: 7W
HDMI Version 1.3
HDCP Version 1.2
Max Video Resolutions 1920 x 1080/1080p @ 60 Hz
MTBF >30,000 hours
Operating Temperature 32° to 140° F (0° to 60° C)
Storage Temperature -4° to 158° F (-20° to 70° C)
Humidity 0 to 95% RH, Non-Condensing
Unit Dimension (H x W x D, in.) 6.2 x 3.5 x 1.1
Unit Dimension (H x W x D, mm) 158 x 89 x 28
Unit Weight (lb.) Tx: 0.96; Rx: 0.98
Unit Weight (g) Tx: 435; Rx: 445
1-Year Limited Warranty
Tripp Lite warrants its products to be free from defects in materials and workmanship for a period of one
(1) year from the date of initial purchase. Tripp Lite’s obligation under this warranty is limited to repairing or
replacing (at its sole option) any such defective products. To obtain service under this warranty, you must
obtain a Returned Material Authorization (RMA) number from Tripp Lite or an authorized Tripp Lite service
center. Products must be returned to Tripp Lite or an authorized Tripp Lite service center with transportation
charges prepaid and must be accompanied by a brief description of the problem encountered and proof of
date and place of purchase. This warranty does not apply to equipment, which has been damaged by accident,
negligence or misapplication or has been altered or modified in any way.
EXCEPT AS PROVIDED HEREIN, Tripp Lite MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Some states do not permit
limitation or exclusion of implied warranties; therefore, the aforesaid limitation(s) or exclusion(s) may not apply
to the purchaser.
EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL Tripp Lite BE LIABLE FOR DIRECT, INDIRECT, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT, EVEN IF ADVISED
OF THE POSSIBILITY OF SUCH DAMAGE. Specifically, Tripp Lite is not liable for any costs, such as lost profits
or revenue, loss of equipment, loss of use of equipment, loss of software, loss of data, costs of substitutes,
claims by third parties, or otherwise.
PRODUCT REGISTRATION
Visit www.tripplite.com/warranty today to register your new Tripp Lite product. You’ll be automatically entered
into a drawing for a chance to win a FREE Tripp Lite product!*
* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.
18-02-433-933756.indb 6 4/11/2018 8:06:23 AM

7
Warranty and Product Registration
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
FCC Notice, Class B
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications to this equipment not expressly approved by Tripp Lite could void the user’s
authority to operate this equipment.
WEEE Compliance Information for Tripp Lite Customers and Recyclers (European Union)
Under the Waste Electrical and Electronic Equipment (WEEE) Directive and implementing regulations,
when customers buy new electrical and electronic equipment from Tripp Lite they are entitled to:
•Send old equipment for recycling on a one-for-one, like-for-like basis
(this varies depending on the country)
•Send the new equipment back for recycling when this ultimately becomes waste
Use of this equipment in life support applications where failure of this equipment can reasonably be expected
to cause the failure of the life support equipment or to significantly affect its safety or effectiveness is not
recommended. Do not use this equipment in the presence of a flammable anesthetic mixture with air, oxygen
or nitrous oxide.
Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice.
18-02-433-933756.indb 7 4/11/2018 8:06:23 AM

8
Manual del
Propietario
Juego Extensor Activo
HDMI sobre la Línea de
Alimentación
Modelo: B126-1A1-PLHD
English 1 • Français 15
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
Copyright © 2018 Tripp Lite. Todos los derechos reservados.
No enchufe esta unidad en un cable extensión, barra de
contactos, supresor de sobretensiones o tomacorrientes
con un breaker por Falla a Tierra (GFCI) o breaker de Falla
por Arco (AFCI).
18-02-433-933756.indb 8 4/11/2018 8:06:23 AM

9
Contenido del Empaque
Accesorios Opcionales
Requisitos del Sistema
Características del Producto
• Unidad Transmisora
• Unidad Receptora
• Cable IR-IN [Cable Infrarrojo de Entrada]
• Cable IR-OUT [Cable Infrarrojo de Salida]
• (2) Cables de Alimentación C7 a NEMA 1-15P, 1.2 m [4 pies]
• Accesorios de Instalación
• Manual del Propietario
• Cables HDMI de Alta Velocidad Serie P568
• Cables HDMI de Alta Velocidad con Ethernet y Conectores Asegurables
P569-XXX-LOCK*
*XXX se refiera a la longitud. Los cables están disponibles en longitudes de 1.83 m [6 pies]
(006), 3.05 m [10 pies] (010) y 4.57 m [15 pies] (015).
• Dispositivo fuente con un puerto HDMI (reproductor Blu-ray, computadora, laptop)
• Dispositivo de visualización con un puerto HDMI (HDTV, proyector, monitor)
• Alimentación de 100V ~ 120V CA
• Extiende señales de audio y video HDMI y de control IR hasta a 300 m de la fuente
• Usa tomacorrientes existentes para extender una señal de 1080p hasta a
300 m @ 60 Hz
• Conveniente control IR para controlar en forma remota la fuente de HDMI
• Puerto de salida HDMI en el transmisor para conectar una pantalla adicional
• Soporta video de alta definición y audio estéreo
• Soporta Color Verdadero de 24 bits (8 bits por canal)
• Compatible con estándares HDMI 1.3 y HDCP 1.2
• Soporta 300 MHz / 3.4 Gbps por ancho de banda de canal (10.2 Gbps en total)
• Operación para conectar y usar sin necesidad de software ni controladores
18-02-433-933756.indb 9 4/11/2018 8:06:23 AM

10
Vista General del Producto
Panel Frontal de Transmisor y Receptor
Panel Posterior del Transmisor
Panel Posterior del Receptor
ALED de Encendido (Azul)—Se enciende para indicar que la unidad está recibien-
do energía.
BLED de Transmisión de Datos (Amarillo)—Destella lentamente mientras se
establece la conexión. Destella rápidamente cuando la unidad se conecta con
éxito y se transmiten datos.
CLED de Conexiones (Verde)—Destella cuando la señal está conectada.
DBotón de Restaurar—Oprima para restaurar la unidad.
EAlimentación de CA C8—Conecta el cable de alimentación C7 a NEMA 1-15P
incluido, 1.2 m [4 pies].
FConector IR-OUT (Hembra)—Se conecta al cable IR-OUT incluido. Para obtener
mejores resultados, el cable IR blaster [Emisor de rayos Infrarrojos] debe colo-
carse cerca del dispositivo fuente.
GConector de Salida HDMI (Hembra)—Se conecta a la pantalla HDMI local con
un cable HDMI (Vendido por separado).
HConector de Entrada HDMI (Hembra)—Se conecta a la fuente HDMI con un
cable HDMI (Vendido por separado).
IAlimentación de CA C8—Conecta el cable de alimentación C7 a NEMA 1-15P
incluido, 1.2 m [4 pies].
JConector IR-IN (Hembra)—Se conecta al cable IR-IN incluido. El control remoto
de la fuente debe estar dentro del rango requerido del receptor IR.
KConector de Salida HDMI (Hembra)—Se conecta a la pantalla HDMI local con
un cable HDMI (Vendido por separado).
A CB D
E F G H
I J K
18-02-433-933756.indb 10 4/11/2018 8:06:23 AM