Tripp Lite B062-002-PS2 User manual

Owner’s Manual
KVM Console Module
Models: B062-002-PS2 & B062-002-USB
This Quick Start Guide briefly describes how to install and operate the B062-002-USB and
B062-002-PS2 Console Module with the B060-032 NetDirector KVM Switch
Package Contents
The complete package consists of:
• B062-002-USB or B062-002-PS2 Console Module
• Custom KVM Cable
• AC Power Adapter
• Quick Start Guide
If anything is missing or damaged, please contact your dealer immediately.
Front View
1. Link LED. Indicates good connection
2. Local LED. Indicates Local PC operation
3. Remote LED. Indicates Remote
Console operation
4. Local / Remote. Toggle Pushbutton
Note: Local PC / KVM Switch operation may also be toggled using the keyboard hotkey combination of [NumLock] + [-][-]
1.Press and hold [NumLock] key
2.Press and release [-] key twice
3.Releass [NumLock] key
Rear View
1 2 3 4 5 1 2 3 4 5
1. Power Jack
2. Local PC Connection
3. KVM Switch Connection
4. Firmware Recovery Switch
5. Console Port Section
B062-002-PS2 B062-002-USB
WARRANTY
REGISTRATION
Register online today for a
chance to win a FREE Tripp Lite
product! www.tripplite.com/warranty
Copyright © 2006 Tripp Lite. All rights reserved. All trademarks are the property of their respective owners.
The policy of Tripp Lite is one of continuous improvement. Specifications are subject to change without notice.
200607033 93-2577 B062 OM.qxd 7/7/2006 2:53 PM Page 1

Hardware Requirements
Console Computer
• A VGA, SVGA or Multisync monitor capable of the highest resolution that you will be using
on any computer in the installation.
• A PS/2 style keyboard (B062-002-PS2) or a USB Keyboard (B062-002-USB)
• A PS/2 style mouse (B062-002-PS2) or a USB mouse (B062-002-USB)
Cables
For optimal signal integrity and to simplify layout, a high-quality Console Module to Local PC
cable (with custom SPHD-15 connector) is included with the Console Module. No additional
cable purchase is necessary.
Hardware Installation
Before you begin, make sure that power to all the devices you will be connecting have been
turned off. You must unplug the power cords of any computer that has a Keyboard Power On
function.
Follow the 4 steps listed below to properly install your Console Module:
1. Plug your keyboard, mouse and monitor into the appropriate console ports of the Console
Module. Each Port is labeled with the appropriate icon.
2. Plug the RJ45 connector into its appropriate port on the rear panel of the Console Module. At
the other end, plug the RJ45
connector into one of the console
ports on the rear panel of the
Matrix KVM Switch
3. For the Local PC connection, use
the cable provided to connect to the
keyboard, mouse and monitor ports
of your local PC. At the other end,
plug the SPHD15 connector into its
appropriate port.
4. Plug in the power adapter, then turn
on the connected computer.
B062-002-PS2 B062-002-USB
B060-032
Warranty Registration
Visit www.tripplite.com/warranty today to register the warranty for your new Tripp Lite product.
You'll be automatically entered into a drawing for a chance to win a FREE Tripp Lite product!*
* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.
Note: Follow these instructions and operating procedures to ensure correct performance and to prevent damage to this unit or to its connected devices.
Tripp Lite World Headquarters
1111 W. 35th Street, Chicago, IL 60609 USA
[phone] • www.tripplite.com 200607033 93-2577
200607033 93-2577 B062 OM.qxd 7/7/2006 2:53 PM Page 2